User Manual

126
Helicopter
Function
Method
① Call the menu screen from the
home screen by pressing the +
key for 1 second.
＋
② Select
from the menu with the
Jog key.
③ Open the setting screen by
pressing the Jog key.
（1 second）
Calling the setting screen
If this trim offset function is used, independent
trim adjustments can be made during hovering and
in the air. This function can offset the ailerons,
elevators, and rudder neutral position by linking
to the set switch or condition. A habit that tends
to appear from the standpoint of helicopter
characteristics when flying at high speed is
possible. This function can correct this habit.
ŏ)RUDFORFNZLVHURWDWLRQURWRUVLQFHWKHKHOLFRSWHU
WLOWVWRWKHULJKWGXULQJÁLJKWXVHWKHRIIVHWIXQFWLRQ
WRVHWWKHVZDVKSODWHVRWKDWWKHKHOLFRSWHUWLOWV
WRWKHOHIW6LQFHWKHGLUHFWLRQRIWKHHOHYDWRUVLV
GLIIHUHQWGHSHQGLQJRQDGMXVWPHQWRIWKHDLUFUDIW
GHFLGHWKHVHWWLQJGLUHFWLRQDIWHUÁLJKW:KHQWKH
J\URLVXVHGLQWKH$9&6PRGHDWWKHUXGGHUHWF
WKHRIIVHWUDWHLVPDGHLQLWLDOVHWWLQJWRPDNH
FRUUHFWLRQVDWWKHJ\URVLGH
ŏ:KHQWKHVZLWFKZDVVHOHFWHGRIIVHWV\VWHPFDQ
EHVHWIRU D SRVLWLRQVZLWFK DQG RIIVHWV\VWHPV
FDQEHVHWIRUDSRVLWLRQVZLWFK/LQNLQJWR
FRQGLWLRQV,'/
,

,
+2/'LVDOVRSRVVLEOH
ŏ:KHQWKHRIIVHWIXQFWLRQLVRQGDWDDGMXVWPHQWLV
SRVVLEOHHYHQE\GLJLWDOWULP7KHWULPDGMXVWHGUDWH
LVLQSXWLQWKHDLU:KHQWKHRIIVHWIXQFWLRQLV21
WKHLQLWLDOVFUHHQWULPGLVSOD\LVOLQNHG
"OFFSET"
OFFSET
Trim offset
(HELICOPTER)
■ Activating the function
＋ −
or
① Select the "MIX" item
and then select the
"ON" or "OFF" by
pressing the + key or ‒
key.
● When you do not use a function, set to the
"INH" side.
■ Switch selection
＋ −
or
② Select the "SW" item
and then select the
switch by pressing the
+ key or ‒ key.
Range：Cond, SwA-SwD
■ Switch direction and condition
selection
③ Select the switch direction and
condition you want to set at the switch
direction and
condition items.
■ Offset rate
④ Select the "RATE" item and then adjust the offset rate
by pressing the + key or ‒ key.
Range：-120 to +120%
Default：0%
● When you want to return the set value to the initial
value, press the + key and ‒ key simultaneously.
Trim offset
● Select the setting item with
the Jog key.
Activating the function
Switch direction,
Selection of condition
Offset rate
Switch selection
● When not using this Function
select INH. The display of On/Off is
shown when active and assigned
to a switch.
（Present condition ）
●When "Cond" is chosen,
if Jog key is pushed for
1 second, it will change
to each condition
setting screen.
＋ −
or