R
Thank you for purchasing the Futaba 3PJ SUPER. Prior to operating your 3PJ SUPER, please read this manual thoroughly and use your system in a safe manner. After reading this manual store it in a safe place. See the glossary on page (P108-109) for the definition’s of the special terms used in this manual. Application, Export and Reconstruction 1. Use this product in surface models only.
THE RBRCTM SEAL (FOR U.S.A.) The RBRCTM SEAL on the (easily removable) nickel-cadmium battery contained in Futaba products indicates that Futaba Corporation of America is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States. The RBRCTM program provides a convenient alternative to placing used nickel-cadmium batteries into the trash or municipal waste which is illegal in some areas.
Table Of Contents For Your Safety As Well As That Of Others........... 6 Explanation of Symbols ................................................................................ 6 Operation Precautions .................................................................................. 7 Nicad Battery Handling Precautions ........................................................... 9 Storage and Disposal Precautions ............................................................ 10 Other Precautions ..............
Steering Speed .................................................................................. 49 A.B.S. Function .................................................................................. 51 Idle-Up ................................................................................................ 55 Throttle Acceleration ........................................................................ 56 Start Function ....................................................................................
For Your Safety As Well As That Of Others Usethisproductinasafemanner.Pleaseobservethefollowingsafetyprecautionsat alltimes. Explanation of Symbols For Your Safety As Well As That Of Others 6 Thepartsofthismanualindicatedbythefollowingsymbolsareextremelyimportant andmustbeobserved. Symbols Explanation Danger Indicates a procedure which could lead to a dangerous situation and may cause death or serious injury if ignored and not performed properly.
Operation Precautions Warning Do not operate two or more models on the same frequency at the same time. Operating two or more models at same time on the same frequency will cause interference and loss of control of both models. AM, FM (PPM) and PCM are different methods of modulation. Nonetheless the same frequency can not be used at the same point in time, regardless of the signal format. Do not operate outdoors on rainy days , run through puddles of water or when visibility is limited.
Caution Prohibited Procedures Do not touch the engine, motor, speed control or any part of the model that will generate heat while the model is operating or immediately after its use. These parts may be very hot and can cause serious burns. For Your Safety As Well As That Of Others Mandatory Procedures Turning on the power switches. Always check the throttle trigger on the transmitter to be sure it is at the neutral position.
Nicad Battery Handling Precautions (OnlywhenNicadbatteriesareused) Warning Always check to be sure your batteries have been charged prior to operating the model. To recharge the transmitter Nicad , use the special charger made for this purpose. Should the battery go dead while the model is operating loss of control will occur and create a very dangerous situation. Overcharging could cause the Nicad battery to overheat, leak or explode.
Storage and Disposal Precautions Warning Prohibited Procedures Mandatory Procedures For Your Safety As Well As That Of Others Do not leave the radio system or models within the reach of small children. A small child may accidentally operate the system, this could cause a dangerous situation and injuries. Nicad batteries can be very dangerous when mishandled and cause chemical damage. Do not throw Nicad batteries into a fire. Do not expose Nicad batteries to extreme heat.
Other Precautions Prohibited Procedures Do not expose plastic parts to fuel, motor spray, waste oil or exhaust. The fuel, motor spray, waste oil and exhaust will penetrate and damage the plastic. Mandatory Procedures Always use only genuine Futaba transmitters, receivers, servos, FET amps (electronic speed controls),Nicad batteries and other optional accessories. Futaba will not be responsible for problems caused by the use of other than Futaba genuine parts.
Before Using Features - Eight Model Memories/Eight More Models Can Be Added By Using the Data Pac EnglishandJapaneseKatakanacharactersmaybeusedtoassigneachmodelaname. Modelmemorieswithslightlydifferentsettingscanbeeasilycreatedbyusingthe modelcopyfunction.Also,eightmoremodelscanbeaddedbyusingtheoptional DataPac(DP-16K). - Large LCD display Before Using Constantlydisplaysalltheinformationneededformonitoring.Thelargecharacters canbeeasilyreadwhenmakingadjustments.
- Advanced Timer (TIMER) Theracingtimer(laptimer)canrecordthetotaltimeandupto99laps.Thetimercan beautomaticallyactivatedbytriggeroperation.Analarmcanbesetfrom30second beforetimeisup. ANavigationtimerthatiseffectiveinpracticerunscanalertyoutothetargetlap. - Digital Trim w/Reset Function ThetrimpositionisconstantlydisplayedontheLCDscreen.One-stepservotravel canalsobeadjusted. Steeringandthrottletrimadjustmentshavenoeffectonthemaximumservotravel.
Set Contents Afteropeningthebox,firstcheckifthecontentsconformtothefollowing.Thecontentsdependonthesetasshownbelow. Before Using Transmitter T3PJ SUPER RF module *Installed in transmitter. Receiver R113F(FM) or R113iP(PCM) Servo S9402, S9304 or (none) Miscellaneous TJ-FM Transmitter Ni-cad battery pack NT8F700B or Battery box *Installed in transmitter. Receiver switch Instruction manual -Ifanyofthesetcontentsaremissing,oryouhaveanyquestions,pleasecontactyou dealer.
Nomenclature Transmitter T3PJ SUPER (Front) (See page 16 for the operating instructions.) Steering trim (DT1) Antenna Steering wheel Throttle trim (DT2) Pilot lamp LCD screen Edit keys PILOT Power switch DIRECT ST.EXP UP SETUP SELECT DOWN - TH.EXP ATV CUSTOM M.SEL + RESET Before Using Traction control switch (SLD) CH3 knob (KNOB) (See page 16 for the operating instructions.) (See page 17 for the adjustment instructions.
Digital Trim Operation (Initial settings: DT1: Steering trim, DT2: Throttle trim, DT3: -------) Operatingbythelever:Pushthelevertotheleftorright(upordown). Operatingbypushbuttonswitch:Pressthepushbuttonswitchinthedesireddirection. ThecurrentpositionisdisplayedontheLCDscreen. ON SLD Steering trim display DT2 Before Using DT.1 Throttle trim display DT3 DT1 Lever Push button switch - Each step is indicated by a tone.
Wheel Tension Adjustment Makethisadjustmentwhenyouwanttochangethesteeringwheelspringtension. Adjustment Turn the screw inside the adjusting hole using a 1.5mm hex wrench. DIRECT - Turning the adjusting screw clockwise, increases the spring tension. SELECT Tension adjusting screw Caution Ifturnedtoofarcounterclockwise,theadjustingscrewmayfallout. Before Using TH.EXP Mechanical ATL Adjustment Makethisadjustmentwhenyouwanttomakethethrottletriggerbrake(back)side strokenarrower.
Transmitter T3PJ SUPER (Rear) (See page 20 for the handling instructions.) (See page 20 for the handling instructions.) RF module DP-16K Data Pac Charging jack DSC jack (See page 103 for the handling instructions.) (The DSC cord sold separately is necessary.) CHG Before Using DSC Dry cell Battery Replacement (For dry cell battery system) 1. Slide the transmitter battery cover in the arrow direction while pressing the part shown in the figure.
Charging the Ni-cad Battery AC outlet Charging Charger 1. Plug the transmitter cord of the special charger into the charging jack on the rear of the transmitter. Transmitter charging LED 2. Plug the charger into an AC outlet. Cord to transmitter charging jack Before Using 3. Check that the charging LED lights. WhenchargingtheNT8F700BNi-cadbatterywiththespecialcharger,allowabout 15hoursforcharging.Ifthetransmitterhasnotbeenusedforsometime,cyclethe batterybycharginganddischargingittwoorthreetimes.
RF Module Removal 1. Pull the RF module forward while pressing the tabs at the left and right inward. Insertion RF module 1. Insert the RF module while being careful not to bend the transmitter side connector pins. Before Using 2. Insert the RF module until the tabs at the left and right snap in place with a “click”. Tabs RF Module Temperature Rise ThetemperatureoftheRFmodulewillriseslightlyduringoperation.
3PJ SUPER and 3VC transmitter data pack compabilitily - Note that the digital trim 3 (DT3) and slide switch (SLD) initialization values are different. -The3VCtransmitterdoesnothaveadigitaltrimfunctionreversefunction.Therefore,whenthe3PJSUPERtransmittercopieddatatoa3VCtransmitter,the3VC ignoresthecopieddata.However,sincethedataisstoredasis,whenthedataisrecopiedtothe3PJSUPERtransmitter,the3PJSUPERwilloperateusingtheoriginal settings.
Transmitter T3PJ SUPER (Side View) Display switch OFF ON POWER DISPLAY SW ON DT.2 Cover Before Using Power switch Sound port - Use a commercial earphone. (Use a radio earphone with a 3.5mm diameter plug.) - When the surroundings are noisy during races, etc., you can listen to the alarm tone using an earphone. The alarm tone can also be heard from the transmitter.
LCD Screen and Edit Keys Whenthetransmitterpowerswitchisturnedon,themodelmemoryNo.andmodel namecurrentlycalledaretemporarilydisplayedforconfirmation. Turn on the power switch Before Using A tone will sound to show that the power is on. After the model No. is displayedforaboutone second, the LCD will switch to the model namedisplay. Afterthemodelnameis displayed for several seconds, the LCD will switch to the timer and voltagedisplay. Model No.
SET-UP Mode Function SelectionSELECT Mode Function Selection To call the function set-up screen in the SET-UP mode, press the UP and DOWN keys simultaneously. After that, select the function with the UP or DOWN key. To end the SET-UP mode, press the UP and DOWN keys simultaneously again, or press the DIRECT key twice. DIRECT Edit keys SELECT TH.EXP To call the function set-up screen in the SELECT mode, press the UP or DOWN key at the initial screen.
LCD Screen Contrast TheLCDscreencontrastcanbeadjusted.(Formoreinformation,seepage94.) Caution DonotadjustthecontrastsothattheLCDistoobrightortoodark. Whenthedisplaycannotbereadduetoatemperaturechange,datacannotbeset. - On hot summer days and cold winter days, the LCD may be easy to read indoors, but difficult to read outdoors. - If the contrast is too bright or too dark, temperature changes and lighting conditions may cause the screen to become difficult to read.
Receiver R113F/R113iP Crystal When changing the frequency, use the specified Futaba crystal set. Antenna FP-R113F FM Connectors 1 2 3 B/C Before Using R113F/R113iP receiver 1: Steering servo (CH1) 2: Throttle servo (CH2) 3: CH3 servo (CH3) B/C: Power connector/DSC connector Forthereceiver,servos,andotherconnections,seepage27.FortheDSCcord(option)connections,seepage103.
Installation Receiver and Servo Connections When connecting and installing the receiver and servos, read the “Installation Safety Precautions”onthenextpage.
Installation Safety Precautions Warning Connector Connections Be sure the receiver, servo, crystal and connectors are fully and firmly connected. If vibration from the model cause a connector to work loose while the model is in operation. You may lose control . Electronic speed control Install the heat sinks where they will not come in contact with aluminum, carbon fiber or other parts that conduct electricity.
Initial Set-Up Preparations (Transmitter) Before setting the transmitter functions, check and set items 1 to 3 below. (Display when power switch turned on) When the power switch is turned on, the currently selected model number is displayed. Check if this number is the model number you want to set-up. To change the model number, use the Model Select function (page 44). Turn on the transmitter power. The model number is displayed for about one second. The model name is displayed for about two seconds.
2. Modulation Mode Check The T3PJ SUPER transmitter output signal format can be changed to match the type of receiver. Check if the modulation mode is set to match the receiver used. When using an FM receiver (e.g., R113F), the modulation mode must be set to PPM. When using a PCM receiver (e.g., R113iP), the modulation mode must be set to PCM. If this setting is incorrect, change it with the Mode Select (page 93) function. 3.
(Set-Up Procedure When Installed In a Car) When installing the servos in a car, performing function set-up in the following order isrecommended. 1. Perform step 3. Trims Initial Set-Up of Preparations on the preceding page. 2. Set the servo direction of operation using the Reverse function. (Page 87) Theservoinstallationmethodandlinkagedirectiondepends on the kit. Therefore, the servo operation direction may have to be reversed relative to transmitter operation.
Direct Mode Functions TheDIRECTmodeallowsinstantaccesstothefivefunctionsmostfrequentlyused. Thefunctionset-upscreencanbedirectlyandquicklycalledwiththespecialkeyfor eachfunction.Ofthefivefunctions,onecanbefreelyselectedastheUserCustom function. Function Map Key layout ST.EXP UP DIRECT M.SEL ?????? (Arbitrary screen) DIRECT SELECT TH.EXP SELECT TH.EXP ST.EXP UP SETUP DOWN ATV "DIRECT" M.SEL + RESET - CUSTOM DOWN ATV CUSTOM DIRECT "TH.EXP" Direct Mode Functions EXPF Throttle EXP "UP" "ST.
Steering ATV TheATVfunctionisusedtosetthesteeringservotravel in both directions using the linkage. Make this setting whentheleftandrightturninganglesandtheturningradiusdifferwiththecharacteristicsofthemodel. e th ! hat vo . n io t er ut ure g s hum Ca e s rin ot B tee s n s oe d Warning When steering, be sure that the servo does not strike the knuckle stopper and unreasonable force is not applied to the servo horn.
5. At the end of adjustment, press the DIRECT key twice. (Returns to the initial screen.) DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM - 2 times Maximum Servo Throw ThesteeringATVfunctiondeterminesthesteeringservomaximumtravel.However, whenthefunctionsbelowareadjusted,themaximumtravelmayexceedthetravel range set by the ATV function. Any time adjustments are made to the following functions,checkyoulinkageinstallation.
Throttle ATV Usethisfunctionwhenadjustingthethrottlehighandlowsidelinkages. Warning Be sure that throttle operation does not apply unreasonable force to the servo horn. Unreasonable force applied to the servo horn may result in damage to the servo and loss of control. First, set ATL dial (initial setting: GD2) for to the maximum servo throw position (100%). DIRECT SELECT TH.EXP 2. Call the ATV function set-up screen by pressing the ATV key. 3.
5. To adjust the brake side (back side), push the throttle trigger all the way to the brake side and adjust the percentage with the + and - keys. However, when using an FET amp, set the percentage to 100%. DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM 点滅 Blink Setting range; 0~120% - Return to the initial value (100%) by pressing the + and - keys simultaneously for about one second. 6. At the end of adjustment, press the DIRECT key twice. (Returns to the initial screen.
Channel 3 ATV UsethisfunctiontoadjusttheCH3servoupanddowntravel. Warning Do not apply unreasonable force to the servo horn during operation. Applying unreasonable force to the servo horn may result in servo damage or loss of control. DIRECT SELECT TH.EXP 2. Call the ATV function set-up screen by pressing the ATV key. 3. Call the Channel 3 ATV function set-up screen by pressing the SELECT key twice. DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV CUSTOM M.SEL ST.
5. To adjust the CH3 up side, set the CH3 dial to full up (100%) and adjust the rate with the + and - keys. DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM 点滅 Blink Setting range; 0~100% - Return to the initial value (100%) by pressing the + and - keys simultaneously for about one second. 100% 6. At the end of adjustment, press the DIRECT key twice. (Returns to the initial screen.) DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.
Steering EXP Thisfunctionisusedtochangethesensitivityofthesteeringservoaroundtheneutral position.Ithasnoeffectonthemaximumservotravel. Racers Tip Whenthesettingisnotdetermined,orthecharacteristicsof themodelareunknown,startwith0%.(WhenEXPissetto 0%,servomovementislinear.) 1. Access the DIRECT mode by pressing the DIRECT key. DIRECT SELECT TH.EXP 2. Call the Steering EXP function set-up screen by pressing the STEXP key. ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM M.
Throttle EXP/EXP2/CRV Thisfunctionchangesthesensitivityofthethrottleservointhethrottletriggerforwardsideandbrakesidedirections.Ithasnoeffectontheservomaximumtravel. Fortheforwardside,theset-upscreenforthecurveselectedwiththethrottlecurve selectionfunction(page98)appearsontheLCD.Thethrottlecurvecanbeselected fromamongthreecurves(EXP/EXP2/CRV). Racers Tip Whenthetrackconditionsaregoodandthereisnosenseoftorqueatthepowerunit, seteachcurvetothe+(quick)side.
(EXP2 curve) TheEXP2curvecanalsobesetfortheforwardside.ThebrakesideistheEXPcurve. 1) When you want to increase the servo sensitivity, pull the throttle trigger to the forward side and adjust with the + key. When you want to decrease the servo sensitivity, push the throttle trigger to the forward side and adjust with the - key. DIRECT SELECT TH.EXP DIRECT SELECT TH.EXP Servo movement +1%∼+100% (quick) Throttle trigger forward side - M.SEL + RESET - CUSTOM Setting range; 20~80% DIRECT SELECT TH.
(CRV curve) The CRV curve can be set for the forward side only. The brake side is set with the EXPcurve. 1) Select the point (P1~P5) of the trigger you want to set with the SELECT key. DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM - Neutral point 0% and high point 100% are fixed and cannot be changed. 2) Set the value of the selected point with the + and - keys. Setting range; 0~100% DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.
4) At the end of adjustment, press the DIRECT key twice. (Returns to the initial screen.) DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM Setting range: -100~0~+100% To return to the initial value (0%), press the + and - keys simultaneously for about one second. DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.
Model Select Usethisfunctiontocallanewmodelnumber,ortochangeasetmodelnumber,toset newmodeldata. TheT3PJSUPERtransmittercanstorethemodeldataforeightR/Ccars.TheDP16KDataPac(Option)canstoremodeldataforeightmoremodels. Themodelnumbersare01to08atthetransmitterand09to16attheDataPac.When theDataPacisnotinstalled,modelnumbers09to16arenotdisplayed. 1. Access the DIRECT mode by pressing the DIRECT key. DIRECT SELECT TH.EXP 2. Call the Model Select function set-up screen by pressing the MSEL key. 3.
Custom Key FunctionscanbefreelyassignedtotheCUSTOMkey.Theassignedfunctioncanbe calledthesameasotherdirectmodefunctions. See“Set-UpModeFunctionSelectSwitch”(page89)foradescriptionofhowto assignafunctiontotheCUSTOMkey. Duringinitialization,thesubtrimfunction(SUBT)isallocatedtothiskey. 1. Access the DIRECT mode by pressing the DIRECT key. DIRECT SELECT TH.EXP 2. Call the set-up screen of the assigned function by pressing the CUSTOM key. DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV CUSTOM M.SEL ST.
Select Mode Functions The function set-up screen can be easily selected from the function menu displayed on the LCD screen. Function Map IDL.UP TH.ACC START TRAC A.B.S AB.P IDLE A.B.S. Idle-up ACCE.F AT.S Throttle acceleration DLY ST.T.S This mode uses the UP or DOWN key to sequentially call the set-up screens from the initial screen. The 10 functions printed around the top of the LCD screen can be called. ST.SPD TURN Steering speed Step Traction control Start TIMER 00:00.
Subtrim センターを出すため に使用する Use this function to adjust the neutral position of the steering, throttle and channel 3 servos. Subtrim shifts the entire servo travel range in the set direction. Use to adjust the neutral position 1. (Beforesettingsubtrim) 3CH 3CH Steering trim 3CH Set the steering and throttle digital trims to the neutral “N” position. Set CH3 to the center“50”position. DIRECT ST.EXP UP SETUP SELECT DOWN - TH.EXP ATV CUSTOM M.SEL + RESET "N"の位置 “N” position Throttle trim 2.
5. Adjust the throttle servo neutral position with the + or key. DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM - Return to the initial value (0%) by pressing the + and - keys simultaneously for about one second. 6. (Channel 3 setting) Press the SELECT key once. The display switches to the CH3 set-up screen. - Install the servo horn in accordance with the kit instruction manual, the same as steering and throttle. DIRECT SELECT TH.EXP 7.
Steering Speed Quicksteeringoperationwillcausemomentaryundersteering,lossofspeed,orspinning. This function is effective in such cases. Smooth cornering Spin Understeering Steering speed not set Operation - This function limits the maximum speed of the steering servo. (Delay function) -Thesteeringspeedwhenthesteeringwheel is operated (TURN direction) and returned (RETN direction) can be independently set. - If the steering wheel is turned slowerthanthesetspeed,thesteering servo is not affected.
4 Adjust the steering servo RETN direction delay with the + or - key. DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV CUSTOM M.SEL ST.EXP UP SETUP DOWN ATV CUSTOM + RESET - (The TURN direction setting is not affected.) 5 At the end of adjustment. press the DOWN key twice, or press the DIRECT key twice. (The display returns to the initial screen.) DIRECT SELECT TH.EXP - Return to the initial value (100%) by pressing the + and - keys simultaneously for about one second. M.
A.B.S. Function When the brakes are applied while cornering with a 4 Wheel Drive or other type of vehicle, understeer may occur. The generation of understeer can be eliminated and corners can be smoothly cleared by using this function. Operation - When the brakes are applied, the throttle servo will pulse intermittently. This will have the same effect as pumping the brakes in a full size car. - The brake return amount, pumping cycle, and brake duty canbeadjusted.
5. (Pumping cycle setting) CYCL 点滅 Blink DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM Press the SELECT key once. The pumping cycle set-up screen is called. Setting range: 1~30 6. Adjust the pumping cycle with the + or - key. DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM - The smaller the value, the shorter the pumping cycle. 7. (Pumping duty ratio setting) Blink Press the SELECT key once. The pumping duty ratio setup screen is called.
11. (Operating point setting) 点滅 Blink DIRECT Press the SELECT key once. The operating point set-up screen is called. SELECT TH.EXP 12. Adjust the throttle trigger operating point with the + or key. Operatingpoint: The throttle trigger position at which the A.B.S. function is activatedcanbeset. ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM Setting range: 10~100% DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.
15. At the end of adjustment. press the DOWN key three times, or press the DIRECT key twice. (The display returns to the initial screen.) DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM - 3 times Switch Setting The A.B.S. function ON/OFF switch can be set with the function select switch function. (Page 89) PSH or SLD can be selected. Dial / Trim Setting The brake return amount (AB.P) and cycle (CYCL) can be controlled with grip dial GD1, GD2 or digital trim DT3, etc.
Idle-Up Use this function to improve the starting characteristics of the engine by raising the idling speed when starting the engine of a gas powered car. Operation Offsets the throttle neutral position to the forward side or brakeside. 1. Call the idle-up function setup screen by pressing the UP key four times at the initial screen. Blink 点滅 DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM - 4 times 2. Adjust the idle-up rate with the + or - key. DIRECT SELECT TH.EXP ST.
Throttle Acceleration Gas powered cars require a slight clearance in the linkage. Therefore, there is a lag time at both the forward and brake sides. The response of an electric car is obtained by reducing this time lag at the transmitter. Carburetor A slight clearance is required at the linkage, but the throttle acceleration function acts to reduce the time lag caused by this clearance. Servo horn Brake side Operation - Sharply increases the throttle response near the throttle triggerneutralposition.
5. At the end of adjustment. press the DOWN key 5 times, or press the DIRECT key twice. (The display returns to the initial screen.) DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM -5 times Select Mode Functions Setting Amount The standard value (100% point) of this setting has an affect on the travel set by the throttle ATV function.
Start Function When the throttle trigger is set to full throttle simultaneously with starting when the track is slippery, the car wheels will spin and the car will not accelerate smoothly. When the Start function is activated, merely operating the throttle trigger slowly causes the throttle servo to automatically switch from the set trigger position to a preset point so that the tires do no loose their grip and the car accelerates smoothly.
3. Set the trigger position with the + or - key. When the throttle trigger is slowly pulled to the forward side after setting, a * will be displayed on the screen at the setposition. 点滅 Blink DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM - Return to the initial value (OFF) Setting range: OFF, 5~100% by pressing the + and - keys simultaneously for about one sec- Blink 点滅 ond. Blink 4. (Presetpositionsetting) Press the SELECT key once.
8. At the end of adjustment. press the UP key 5 times, or press the DIRECT key twice. (The display returns to the initial screen.) DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM -5 times Presetting by switch (engine cut, etc.) 1. Select throttle preset (THPR) at the push-button switch (PSH) with the function select switch function. (Page 89) 2. Press the DOWN key five times at the initial screen. The start function setup screen is called. Blink DIRECT SELECT TH.EXP ST.
Traction Control Smooth, fast starting is possible Sudden trigger operation on a slippery track not only causes the wheels to spin, but also prevents smoothacceleration.Smoothandpleasantcontrol is possible and battery consumption can be minimized by setting the traction control function.
点滅 Blink 5. (Delay point setting) Press the SELECT key once. 6. Set the delay point with the + or - key. DIRECT SELECT TH.EXP 0% RNG RNG L50% L50%の場合 M.SEL + RESET - CUSTOM Setting range: OFF, L99~L1,ALL, H1~H99,OFF “H”: High side traction control “L”: Low side traction control “ALL”: Delay applied over the entire range traction control range. - Return to the initial value (L40%) by pressing the + and keys simultaneously for about one second. 50% 99% DIRECT SELECT TH.
Step This function allows you to change the increment of the trim movement. This will allow even finer adjustments to be made when the model is trimmed. Functions Whose Step Amount Can Be Adjusted The number of clicks of the steering trim, throttle trim, ATL function, D/R function, channel 3, traction control function, throttle EXP function, steering EXP function and A.B.S. function can be changed. Blink 点滅 DIRECT SELECT TH.EXP M.SEL + RESET - CUSTOM - 3 times 2.
Timer The timer function can be used as an up timer, down timer, lap navigation timer, and lap timer. The transmitter can operate the timer even outside the timer screen. However, each time the power is turned on, the timer screen is called and the timer must be set. Up Timer/Down Timer Up timer function - This function is used to measure the time from start to stop. - The timer is started and stopped each time the switch is operated and the time from start to stop is integrated and displayed.
Up Timer/Down Timer Setting 1. Call the timer screen by pressing the DOWN key twice at the initial screen. 点滅 Blink DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM - 2 times 2. Call the timer type selection screen by pressing the SELECT key once. 点滅 Blink DIRECT SELECT TH.EXP 3. Select UP or DN with the + or - key. ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM UP: Up Timer DN: Down Timer DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM 4.
Up Timer/Down Timer Operating Instructions (Start/stop) When the timer switch (initial setting: PSH) is pressed, the timer starts. When the timer switch is pressed again, the timer stops. The time can be accumulated by repeating these start and stop operations. (Reset) 1. Press the DOWN key two times at the initial screen. The timer screen is called. UP: Up timer DN: Down timer 2. Press the + and - keys simultaneously for about one second. The timer is reset. 3.
Lap Navigation Timer Lap Navigation Timer Function - Use this function when you want to generate an audible alarm at a fixed interval. Since only the audible alarm can be restarted while the timer is operating, this function can also be used as a target time during practice runs, etc. (Navigation buzzer) - The timer is started and stopped each time the switch is operated and the accumulated time from start to stop is displayed.
6. (Prealarmsetting) 点滅 Blink Call the prealarm set-up screen by pressing the SELECT key once. DIRECT SELECT TH.EXP 7. Set the prealarm time with the + or - key. DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM M.SEL + RESET - CUSTOM Setting range: OFF, 1~30s s: second - Return to the initial value (OFF) by pressing the + and - keys simultaneously for about one second. 8.
Lap Navigation Timer Operating Instructions (Start/navigation buzzer restart/stop) When the timer switch (initial setting: PSH) is pressed, the timer starts and an audible tone sounds at a preset interval. (Navigation buzzer) Thereafter, the buzzer is restarted each time the timer switch is pressed. When the SELECT key is pressed, the timerstops. (Reset) 1. Press the DOWN key two Blink times at the initial screen. The timer screen is called. DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.
Lap Timer Lap Timer Functions - The lap time can be recorded each time the switch is operated. (99 laps) -The race time (audible alarm) can be set. The timer can be automatically stopped by switch operation after the alarm. Prealarm can also be set. The elapsed time can also be indicated by sounding of a buzzer every minute after starting. Alarm: An audible alarm is heard at the set time. Prealarm: A warning tone is heard at the set time before the alarm.
Lap Timer Setting 1. Call the timer screen by pressing the DOWN key twice at the initial screen. 点滅 Blink DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET CUSTOM - 2 times 2. Call the timer type selection screen by pressing the SELECT key once. 点滅 Blink DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM 3. Select LP with the + or - key. 点滅 Blink DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL CUSTOM ST.EXP UP SETUP DOWN ATV CUSTOM + RESET - 4.
Lap Timer Operating Instructions (Start/lap update/stop) When the timer switch (initial setting: PSH) is pressed, the timer starts. When the timer switch is pressed at each lap, the lap times are sequentially memorized. When the timer switch is pressed after the alarm (after the race time has elapsed), the timer stops. - The current lap time is displayed for three seconds simultaneously with lap switch input.
Lap Time Recall Operation 1. Call the timer screen by pressing the DOWN key twice at the initial screen. Blink DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV CUSTOM M.SEL ST.EXP UP SETUP DOWN ATV CUSTOM ST.EXP UP SETUP DOWN ATV CUSTOM ST.EXP UP SETUP DOWN ATV CUSTOM ST.EXP UP SETUP DOWN ATV CUSTOM ST.EXP UP SETUP DOWN ATV CUSTOM ST.EXP UP SETUP DOWN ATV CUSTOM + RESET - - 2 times 2. (Lap recall screen call) Blink Call the recall screen by pressing the SELECT key fourtimes.
Model Name This function allows you to assign a six character name to each model memory. JapaneseKatakanaandEnglishcharacters,symbols,andnumberscanbeused. 1. Call the model name set-up screen by pressing the DOWN key once at the initial screen. (The first column blinks.) 2. Move the cursor (blinking) to the column you want to change using the SELECT key. 3. Change the character using the + or - key. DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.
Setup Mode Functions Key layout The functions in the Set-Up mode are made up of functions that are not changed after basic setting and functions that are not changed very much after being set. To prevent accidental changing of the settings, this menu is separate from those of the othermodes. UP DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM DOWN Function Map ATL ATL "UP" 3CH TH.
Dual Rate/Second Dual Rate Dual Rate This function adjusts the + side when the servo travel is insufficient due to understeering and the - side when the servo travel is excessive due to oversteering on corners while running. This setting is linked to transmitter grip dial GD1. When GD1 is assigned to another function, set dual rate with this screen. Second Dual Rate Use this function when facing a fence due to a crash, etc.
6. At the end of adjustment, press the UP and DOWN keys simultaneously. Or press the DIRECT key twice. (The display returns to the initial screen.) DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM Setup Mode Functions Switch Setting The Second Dual Rate function must be assigned to a switch in advance using the function select switch.
ATL Function This function adjusts the - side when the braking effect is strong and the + side when the braking effect is weak. This setting is linked to transmitter grip dial GD2. When GD2 is assigned to another function, set the ATL function with this screen. Operation The throttle brake side (when the throttle trigger is pushed forward)brakeamountcanbeadjusted. 1. Call the Set-Up mode screen by pressing the UP and DOWN keys simultaneously at the initial screen. 2.
Channel 3 Position Use this function to set the servo position of the channel 3. This setting is linked to transmitter KNOB. When KNOB is assigned to another function, set the channel 3 position with this screen. 2. Call the Channel 3 Position screen by pressing the UP or DOWN keys in function map order. 3. Adjust the servo position with the + or - key. DIRECT SELECT TH.EXP DIRECT SELECT TH.EXP DIRECT SELECT TH.EXP 4. At the end of adjustment, press the UP and DOWN keys simultaneously.
Throttle Neutral The throttle servo neutral position can be switched to 5:5 or 7:3 by switching throttle neutral. 7:3 7:3の場合 5:5 5:5の場合 Forward side Forward side 5：5 7：3 Brake back side Brake back side ブレーキ ブレーキ 前進側 前進側 バック側 バック側 1. Call the Set-Up mode screen by pressing the UP and DOWN keys simultaneously at the initial screen. 2. Call the Throttle Neutral function screen by pressing the UP or DOWN keys in function map order. Setup Mode Functions 80 3.
Programmable Mixing 1/2 These functions allow you to apply mixing between the steering, throttle, and channel3channels. Two programmable mixing systems can be used. The programmable mixing 1 and programmablemixing2set-upscreensareindependent. Additional Functions -When the steering or throttle channel is the master channel (channel that applies mixing), trim data can be added. (However, they do not operate as center trim.) - The mixing mode selection.
6. (Slave channel setting) Call the SLV set-up screen by pressing the SELECT key once. 7. Select the slave channel with the + or - key. DIRECT SELECT TH.EXP DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM ST.EXP UP SETUP DOWN ATV M.SEL CUSTOM ST.EXP UP SETUP DOWN ATV CUSTOM + RESET - Setting range: ST: Steering TH: Throttle 3CH: Channel 3 8. (Mixing rate setting) Call the mixing rate set-up screen by pressing the SELECT key once.
12.(Trimsetting) Call the trim set-up screen by pressing the SELECT key once. 13.Select ON or OFF with the + or - key. DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM Setting range: ON, OFF DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL CUSTOM ST.EXP UP SETUP DOWN ATV CUSTOM + RESET - ON: Trim is added OFF: Trim is removed 14.(Offsetsetting) 15.Set the master channel offset point with the + or - key. DIRECT SELECT TH.EXP DIRECT SELECT TH.EXP M.
Mixing Rate Setting When you want the slave channel to operate the same amount (initial setting) as the master channel, make the following value the standard. When the steering or throttle channel is the master channel, set the mixing rate to 75%. When CH3 is the master channel, set the mixing rate to 90%. Slave Channel Operation The master channel controls slave channel operation or trim.
Tilt Mixing Use this function when you want to apply both directions mixing from steering to channel 3 and from channel 3 to steering with boats. 2. Call the Tilt Mixing screen by pressing the UP or DOWN keys in function map order. 3. Set tilt mixing to ON with the + or - key. DIRECT SELECT TH.EXP DIRECT SELECT TH.EXP DIRECT SELECT TH.EXP 4. (Steering -> channel 3 mixing ratesetting) DIRECT SELECT TH.EXP Call the set-up screen by pressing the SELECT switch once. 5.
8. At the end of adjustment, press the UP and DOWN keys simultaneously. Or press the DIRECT key twice. (The display returns to the initial screen.) DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV M.SEL + RESET - CUSTOM Affect of Set Value on Other Functions Setting of the ATV function, steering EXP function, steering speed function, or dual ratefunctionatthesteeringsidealsoaffectschannel3sideoperation.However,even if the reverse function is set at the steering side, channel 3 is not reversed.
Servo Reverse / Function Reverse This function reverses the direction of operation of the servos related to transmitter steering,throttle,andchannel3operation.Thedatavalueincrease/decreasedirection relative to GD1, GD2, KNOB, DT1, DT2 and DT3 operation can be changed. For PSH, the ON and OFF operation system is changed. However, when the position set by trim or subtrim shifts from the center, the center becomestheoppositeside. 2.
Function Select Trim A function can be assigned between grip dial 1/2, knob, and digital trim 1/2/3. Settable Functions Dual rate function, ATL function, steering trim, throttle trim, traction control function (delay), A.B.S. function AB.P (return amount), A.B.S. function CYCL (cycle), channel 3, steering EXP, throttle EXP (forward side), throttle EXP (brake side), or OFF (not used) can be assigned. 1. Call the Set-Up mode screen by pressing the UP and DOWN keys simultaneously at the initial screen. 2.
Function Select Switch This function assigns a function to push switch PSH, slide switch SLD and the custom key. Settable Functions Push switch (PSH) LAP: Timer THPR: Throttle preset TRC: Traction control ABS: A.B.S. function IDLE: Idle-up D/R2: Dual rate switching CH3: Channel 3 PMX1: Programmable mixing 1 ON/OFF PMX2: Programmable mixing 2 ON/OFF OFF: (Not used) Slide switch (SLD) TRC: Traction control ABS: A.B.S.
1. Call the Set-Up mode screen by pressing the UP and DOWN keys simultaneously at the initial screen. 2. Call the Function Select Switch function screen by pressing the UP or DOWN keys in function map order. 3. (Selection of switch you want to set) DIRECT SELECT TH.EXP DIRECT SELECT TH.EXP DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV CUSTOM M.SEL ST.EXP UP SETUP DOWN ATV CUSTOM ST.EXP UP SETUP DOWN ATV CUSTOM ST.EXP UP SETUP DOWN ATV CUSTOM ST.EXP UP SETUP DOWN ATV CUSTOM + RESET - M.
Fail Safe (PCM Mode Only) This function allows the steering, throttle, and channel 3 servos to move to a preset position when signals cannot be received from the transmitter for some reason. Fail Safe Reset When the receiver can receive signals from the transmitter once more, the fail safe function is automatically reset. 2. Call the Fail Safe function screen by pressing the UP or DOWN keys in function map order. DIRECT SELECT TH.EXP DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV CUSTOM M.SEL ST.
Battery Fail Safe (PCM Mode Only) This function will move the throttle servo to the preset Fail Safe position when the receiver battery voltage drops below a specified value. See page 91 for a description of the Fail Safe function. (This function can be used only with PCM1024 system receivers.) Battery Fail Safe Reset When the battery voltage recovers, the Battery Fail Safe function is reset. 1. Call the Set-Up mode screen by pressing the UP and DOWN keys simultaneously at the initial screen. 2.
PCM/PPM Select This function changes the format of the signals output from the transmitter. (PPM <-> PCM) Receiver When a PCM receiver is used, the transmitter must be set to PCM. When an FM receiver is used, the transmitter must be set to PPM. 2. Call the PCM/PPM Select function screen by pressing the UP or DOWN keys in function map order. DIRECT SELECT TH.EXP DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV CUSTOM M.SEL ST.EXP UP SETUP DOWN ATV CUSTOM + RESET - M.SEL + RESET - 3.
LCD Contrast Adjustment This function adjusts the LCD screen contrast in eight steps. (This is common to all themodelmemories.) 1. Call the Set-Up mode screen by pressing the UP and DOWN keys simultaneously at the initial screen. 2. Call the LCD Contrast Adjustment screen by pressing the UP or DOWN keys in function map order. DIRECT SELECT TH.EXP DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV CUSTOM M.SEL ST.EXP UP SETUP DOWN ATV CUSTOM + RESET - M.SEL + RESET - 3.
Audible Alarm Tone The tone of the key input and other confirmation tones can be changed. (This setting is common to all the model memories.) Audible Alarm Tone However, the alarm tones listed below remain at the initial value (75) regardless of this setting. - Low battery alarm LOWBATT - Idle-up warning - Memory error MEMERR - Back-up error BU.ERROR - Memory select error MSELERR - Data Pac error CAMERR 2. Call the Audible Alarm Tone function screen by pressing the UP or DOWN keys in function map order.
Model Reset This functions resets the contents of the currently called model memory to the initial value. However, it does not reset the PCM/PCM select, total timer, lap memory, timer time, contrast,andaudiblealarmtonesettings. 1. Call the Set-Up mode screen by pressing the UP and DOWN keys simultaneously at the initial screen. 2. Call the Model Reset function screen by pressing the UP or DOWN keys in function map order. DIRECT SELECT TH.EXP DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV CUSTOM M.
Model Copy This function copies the entire contents of the currently called model memory to anothermodelmemory. 2. Call the Model Copy function screen by pressing the UP or DOWN keys in function map order. DIRECT SELECT TH.EXP DIRECT SELECT TH.EXP ST.EXP UP SETUP DOWN ATV CUSTOM M.SEL ST.EXP UP SETUP DOWN ATV CUSTOM + RESET - M.SEL + RESET - 3. (Copydestinationselection) Select the copy destination model memory by pressing the SELECT key.
Throttle Curve Selection This function selects the throttle forward curve. The throttle EXP function (page 40) sets the throttle curve itself. EXP, EXP2, or CRV can be selected as the throttle curve. 1. Call the Set-Up mode screen by pressing the UP and DOWN keys simultaneously at the initial screen. 2. Call the Throttle Curve Selection screen by pressing the UP or DOWN keys in function map order. 3. Select the curve with the + or - key. DIRECT SELECT TH.EXP DIRECT SELECT TH.
Rate Display Selection The channel 3 display can be changed to another function rate display. Selectable Displays 3CH: Channel 3 STEX: Steering EXP TEXF: Throttle EXP (forward side) TEXB: Throttle EXP (brake side) AB.P: A.B.S. function AB.P (return amount) CYCL: A.B.S. function CYCL (cycle) TRCD: Traction control (delay) 2. Call the Rate Display Selection screen by pressing the UP or DOWN keys in function map order. 3. Select the function you wish to display with the + or - key. DIRECT SELECT TH.
Reference Ratings *Specifications and ratings are subject to change without prior notice. Reference 100 Transmitter T3PJ SUPER (Wheelsystem,3channels) - Transmitting frequencies 27, 29, 40, 41 or 75MHz band (TJ-FM RF module used) - Modulation FM (PCM<->PPMswitchingpossible) -Powerrequirement (Ni-cadbattery) NT8F700B Ni-cad battery (9.
Optional Parts The following parts are available as 3PJ SUPER options. Purchase them to match your application. For other optional parts, refer our catalog. Crystal Set There are crystals for FM and AM, depending on the modulation mode, and crystals for single conversion and dual conversion, depending on the receiver circuitry. The R113iP and R113F are FM receivers. Use single conversion crystal sets with them. Warning Use only genuine Futaba crystal (receiver).
Battery Holder (Transmitter) This battery holder is necessary when using the transmitter with a dry cell battery. For a description of how to install the battery holder to the transmitter, see “Ni-cad Replacement”onpage18. Part name 3PJ transmitter battery holder Caution Insert the batteries in the correct polarity. If the polarity is incorrect, the transmitter may be damaged. (Penlight cell x 8) When the transmitter is not in use, remove the batteries.
DSC cord When the TPJ SUPER transmitter and FP-R113iP or FP-R113F receiver are connected with the DSC cord, the servos can be operated without transmitting a signal. (DSC function) Part name DSC cord for 3PJ SUPER Connection 1 2 3 B/C To receiver battery To servos - When used fully up to channel 3, the Y-Adapter must be purchased separately.
Troubleshooting If your system fails to operate or you experience a short range problem or erratic control. Check the table below for reasons you may be having these problems. After you followed the suggestions listed and the problem is not corrected return the system to our service department for inspection and repair. (Item Check) Transmitter Battery (Symptom) Voltage display does not work. System operates intermittently Dead battery -> Change the batteries.
Error Displays Low Battery Alarm If the transmitter battery voltage drops to 8.5V or less, an audible alarm will sand and “LOW BATT” will be displayed on the LCD screen. LCD screen: Warning When a low battery alarm is generated, cease operation immediately and retrieve the model. 点滅 Blink Audible alarm: Continuous tone. If the battery goes dead while in operation, you will lose control.
LCD screen: Audible alarm: Tone sounds (7 times) and stops (repeated) 点滅 Blink Data Pac Error If data transfer with the Data Pac was not performed normally, an audible alarm will sound and “CAMERR” will be displayed on the LCD screen. - To stop the alarm, press the + and - keys simultaneously for about one second. - Turn the power back on. If the alarm is not generated, there is no problem.
Glossary The following defines the symbols and terms used in this instruction manual Band Throttle Frequency that receiver and transmitter operate on. Devise that controls the air mixture at the engine intake. When opened a large air mixture is sucked in and the engine speed increases. When closed the engine speed decreases. Channel Represents the number of functions the transmitter will control. Throttle Trigger Kit Devise provided on the transmitter to control the throttle.
Glossary (LCD Display) The Glossary gives the definition and number of the page that describes the related function for the symbols displayed on the LCD screen. 0:00 10.1v 01MDL-01 3->S 3CH.S Accumulated time/power supply voltage display (P23) Model number/model name (P74) Tilt mixing CH3->Steering mixing (P85) Channel 3 (step) (P63) ACCE.F ALRM. AT.S ATL. ATL.S ATV.B ATV.D ATV.U ATV.F ATV.L ATV.R A.B.S. function brake position (P51) A.B.S.
- Copy and use. 3PJ SUPER Data Sheet Model number: Model name: [SET-UP MODE] [DIRECT MODE] D/R ATV ST:R ST:L % TH:F % TH:B % 3CH:U % 3CH:D % % ST.EXP ATL: EXP: 3CH: EXPB: % D/R2: % % 3CH % TH.EXP % EXPF: % TH.N % TG.P: % PM1 TH.EXP2 % TH.N: 5:5 / 7:3 EXP2: TH.
- Copy and use. ●コピーしてお使いください。 Throttle Curve Model No.: モデルNo.： Model Name: モデルネーム： 100% Set value 設 定 値 50% 0% P2 P1 P3 P4 P5 Trigger point スティックポイント 初期値 value Initial （ノーマルカーブ） (normal value) Throttle curve initial value スロットルカーブの初期値 0% P1 P2 P3 P4 P5 16% 33% 50% 67% 83% 100% FUTABA CORPORATION Makuhari Techno Garden Bldg.
