Instruction Manual

118
7HFKQLFDO6SHFL¿FDWLRQV........................................................................................................................................................ 9
7KHUPDOKXQWLQJVHWXSXVLQJVSHFL¿FSURJUDPPLQJVHWXSVWRKDYHWKHPRGHOUHVSRQGQRWLFHDEO\WRWKHOLIWRIDWKHUPDO
Not a pre-programmed mix. See Programmable mix.
THR-DELAY
: (
ACRO
) throttle delay, slows engine servo response to imitate the spool-up action of a turbine engine. May also
be used creatively to create a delayed servo on a different function (see www.futaba-rc.com\faq\faq-9c.html.) ............... 66
THR-REV
: reverses the throttle trim function to the top of the THROTTLE STICK. ........................................................... 38
THROTTLE-NEEDLE
: (
ACRO

HELI
) curve mix that adjusts a second servo, controlling the engine’s mixture, to get optimum
RPM and performance from the engine at all settings. ........................................................................................................ 65
Throttle-to-rudder mix: used to compensate with rudder when throttle is applied on take off. Not a pre-programmed mix.
See Programmable mix. This is the default setting of a mix in
ACRO
and
GLID
.
THROTTLE CURVE
: (
HELI
) adjusts how the servo responds to the THROTTLE STICK position along a 5 point curve.
Separate curves available for each idle-up and normal. For simplicity, normal curve may be edited from
BASIC
menu. All
curves may be edited together in the
ADVANCE
menu. Activating an idle-up’s throttle curve is what activates that idle-up.
.86,89
Throttle cut or throttle kill:
THR-CUT
. (
ACRO

HELI
) Offset mix which closes the throttle servo to a set position when the
assigned switch is moved to shut the engine off without having to alter trim settings. ....................................................... 40
THROTTLE HOLD
: (
HELI
) makes the throttle servo non-responsive to THROTTLE STICK position, and moves the throttle to
idle. Used to practice autorotations. NOTE: THR-HOLD must be activated, then the default pitch curve adjusted properly.
............................................................................................................................................................................................. 99
THROTTLE MIX
(
HELI
FDQ EH VHW IRU HDFKÀLJKW FRQGLWLRQ DQG LV XVHGWR FRUUHFW WKH WHQGHQF\ RIWKH PRGHO WRFKDQJH
altitude when the rotor is tilted by aileron, elevator, and rudder controls. .......................................................................... 96
Throttle trim adjustment: see
ATL
to change throttle trim from “idle only” to full trim control like all other channels. See
THR-REV
to reverse THROTTLE STICK completely, including moving trim to the top of the THROTTLE STICK. See
also Idle management for details on idle down and throttle cut functions.
TIMER
DGMXVWWKHWLPHUIXQFWLRQVXVHGWRNHHSWUDFNRIÀLJKWWLPHRQDWDQNRIIXHOHWF7KH³WULJJHU´WRWXUQWLPHUVRQRII
may be programmed. ........................................................................................................................................................... 45
TRAINER
: software that allows two radios to be connected via trainer cord, giving student control of all or some of the
FKDQQHOVRIWKHDLUFUDIWDWWKHÀLSRIDVZLWFK
FUNC
trainer mode allows student to use mixing in the master transmitter, for
H[DPSOHGXDOUDWHVH[SRQHQWLDOÀ\DFKDQQHOKHOLFRSWHUZLWKDFKDQQHOEXGG\ER[HWF........................................... 47
Trainer box: stripped-down radio system which does not have the ability to transmit, is used only as a student’s radio when
instructing while using a trainer cord and the trainer programming.
7UDLQHUFRUGFRUGXVHGWRFRQQHFWWZRFRPSDWLEOHUDGLRVWRXVHIRUÀLJKWLQVWUXFWLRQ6HHAccessories.
TRIM
menu: adjusts rate at which the trim responds to movement of the trim sliders.
Also has a reset function to reset the
model’s electronic trims to zero. .......................................................................................................................................... 48
TRIM OFFSET
: (
HELI
) sets an offset or adjustment of trim when switching between conditions. See OFFSET.
TRIM
option in mixes: ability to adjust the slave servo’s center when the master servo’s center is adjusted using the trim
VOLGHUVIRUH[DPSOHZKHQXVLQJWZRVHSDUDWHÀDSVHUYRV6HHProgrammable mix. ........................................................ 61
7ULSOHUDWHUGFRQWUROWUDYHOVHWWLQJDYDLODEOHLQÀLJKW6HH
D/R
,
EXP
.
7ZLQDLOHURQVHUYRVXVHRIWZRRUPRUHVHUYRVRQVHSDUDWHFKDQQHOVWRFRQWURODLOHURQDFWLRQ,QFOXGHVÀDSHURQDLOHURQ
differential, and elevon. ....................................................................................................................................................... 51
Twin elevator servos: use of two or more servos on separate channels to control the elevator of a model. Includes elevon,
ailevator, V-tail. .................................................................................................................................................................... 58
Tx: transmitter.