PRINTER PP-505 (For FE-700)
SAFETY INSTRUCTIONS Safety Information for Operator Safety Information for Installer WARNING WARNING ELECTRICAL SHOCK HAZARD Do not open the cover of the equipment. Only qualified personnel should work inside the equipment. This equipment uses high voltage electricity which can shock or burn. Only qualified personnel should work inside the equipment. This equipment uses high voltage electricity which can shock or burn.
WARNING LABEL A warning label is attached to the printer. Do not remove the label. If the label is missing or damaged, contact your dealer about replacement. WARNING To avoid electrical shock, do not remove cover. No user-serviceable parts inside. Name: Warning Label (1) Type: 86-003-1011 Code No.
FOREWORD A Word to the Owner of the PP-505 Congratulations on your choice of the FURUNO PP-505 Printer. For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for innovative and dependable marine electronics equipment. This dedication to excellence is furthered by our extensive global network of agents and dealers. Your printer is designed and constructed to meet the rigorous demands of the marine environment.
TABLE OF CONTENTS 1. OPERATION.................................................................................................. 1 1.1 1.2 1.3 General..............................................................................................................................1 Panel .................................................................................................................................1 Turning on the Power..........................................................................
1. OPERATION 1.1 General 1.2 Operation of the PP-505 is simple; just turn on the power. The depth graph or the log, whichever is selected for printing, is printed out at the interval set. Panel Power Switch PRINTER PP-505 GRAPH LOG PAPER Below are example printouts. MODE INTERVAL POWER ON RANGE FEED/MARK Thermal Paper Cover 2003/12/01 13:05:00 038.6m/01.0m 35 20.02’N/135 45.15’E 15.1kt 008.
OPERATION Changing the mode Feeding the paper/Printing the marker Press the [MODE] key to change the printing mode from depth graph to log printing alternately. To feed the paper, press and hold down the [FEED/MARK] key. Press the [FEED/MARK] key momentarily to print the marker. The printing interval setting is printed whenever the [MODE] key is pressed. 1.3 Changing the printing interval Turning on the Power Flip down the thermal paper cover and turn on the [POWER] switch.
2. REPLACEMENT OF THERMAL PAPER When the thermal paper runs out, the PAPER LED blinks, printing stops automatically and the audible alarm sounds for five seconds. With 1 m of paper remaining, a red paper end mark appears on the paper. When the red mark appears, replace the thermal paper as shown in the procedure below. Adhesive may remain on the paper after tape is removed. This may cause a paper jam, so cut paper to remove adhesive.
3. INSTALLATION 3.1 Complete Set Name Type Mass Qty 3.1 kg (with hanger) 1 Main Unit PP-505 Spare Parts SP08-01600 1 Installation Materials CP16-00800 1 Accessories FP08-00500 1 Flush Mount Kit OP08-4 1 3.2 Remark Option (004-511-330) Heat accumulation General Mounting Considerations The PP-505 consumes very little power, so there is no need for forced air ventilation. However, it is recommended to provide at least some space around the unit to allow for circulation of cooling air.
3. INSTALLATION 3.3 Tabletop/Bulkhead Mount 3.4 Flush mount panel kit is optionally supplied. The main unit can be mounted on a desktop, bulkhead, or in a panel. Make sure the selected location is strong enough to support the main unit against possible vibration and shock. If necessary, appropriate reinforcement measures should be made on the mounting area. Flush mount kit OP08-4 (Code No.: 004-511-330) Name Flush mount panel Tapping screw Nylon washer Pan head screw Hex.
3. INSTALLATION 3.5 1. Referring to the illustration below, prepare a cutout in the mounting area and drill four pilot holes for the flush mount angles. Refer to the interconnection diagram at end of manual for connection. Refer to the outline drawing at end of manual. 2. Fix the liner and the flush mount angles to the main unit. 3. Connect the cables at the rear of main unit. 4. Fix the main unit to the panel cutout with four tapping screws. 5.
4. MAINTENANCE Checking the power connector Fuse Replacement Check for loosened or disconnected power connector. To protect the equipment from serious damage, a 3A fuse is provided on the rear cabinet of the main unit. The fuse protects against overvoltage/reverse polarity of the ship’s mains or internal fault of the equipment. If the fuse has blown, first find out the cause of the trouble before replacing it.
APPENDIX REPLACEMENT OF PRINTER ASSEMBLY/TERMAL HEAD 1. Loosen the four M4 × 15 screws fixing the rear cabinet to the main unit assembly. 2. Disconnect the connectors connected to the rear cabinet to detach the rear cabinet. 4. Move the carriage to position A by rotating the carriage shaft by fingers, as shown below, where the thermal head assembly can be replaced easily. Carriage Shaft Carriage Rear Cabinet P1 NH 4P A P5 NH 6P M4 × 15 screw (4 pcs.) Main Unit Assembly 3.
6. Pull out the connector end of the flexible cable from the connector. Take care not to damage the flexible cable. End of Flexible Cable (Connector) 9. Hold the flexible cable end with a tweezers and pull it out until it is positioned as shown below. 180° Head Holder 90° Thermal Head 7. Remove the thermal head from the head holder with a screwdriver as shown below, and then take the thermal head assembly out of the printer assembly. Thermal Head 10.
11. Fix the flexible cable to the carriage with the flexible cable support, inserting the projection on the carriage into the hole of the cable. 12. Fold back the end of the cable and insert it into the connector.
FURUNO SPECIFICATIONS OF PRINTER PP-505 1 DATA FORMAT 1.1 Receiving System RS-232C 1.2 Speed 9600 bps 1.3 Data Length 8 bits 1.4 Parity Non 1.5 Stop Bit 1 bit 2 PRINTER SECTION 2.1 Printing System 9 dots serial thermal head printing system 2.2 Character Alphanumeric 2.3 Dot Pitch 0.28 mm/ dot 2.4 Number of Dot in Line 300 dots 2.5 Number of Characters Max. 80 characters/ line 2.6 Print Speed 31 characters/second 2.
Takahashi T. Takahashi T.
Takahashi T. Takahashi T.
C B A 08S0157 *3 FM14-2P NOTE 1. LOCAL SUPPLY. 2. MAX 15m. 3. FITTED AT FACTORY. 4. GROUNDING WITH CONNECTOR HOUSING. 注記 1) 現地手配。 2）最大15m。 3）工場にて取付済み。 4) コネクタケースでアース。 船内電源 SHIP'S MAINS 12-32 VDC 1 1 2 PP-505 PRINTER プリンタ 2 08S0087 RXD (H) 1 TXD (H) 2 0V 3 TXD (C) 4 RXD (C) 5 +12V 6 N.C. 7 *4 P C2366-C03-A Takahashi T. APPROVED DWG.No. *2 H. Maki Takahashi T. P 16-006-3022-0 FE-700 CO-SPEVV-SD-C0.2x2P, φ13.
