FACSIMILE PFX-50 (Incl.
C Yo u r L o c a l A g e n t / D e a l e r 9-52, Ashihara-cho, Nishinomiya, Japan Te l e p h o n e : Te l e f a x : 0 7 9 8 - 6 5 - 2 111 0798-65-4200 All rights reserved. Printed in Japan PUB. No. OME-55896 (TENI) P F X - 5 0 ( FA X ) FIRST EDITION D : : DEC. 1994 O C T.
Dialing Subscribers (Example) Direct dialing Ship (FELCOM) - Land ............. LES No. Service Country Code Code # START Fax No. Normally enter 00 for automatic connection. Ship (FELCOM) - Ship (Inmarsat-B) ............. LES No. Service Code Sea area No. # START Vessel ID No. Ship (FELCOM) → Ship (Inmarsat-A) 81 LES No. Service Code Sea area (At any time) No. ............. # START Vessel ID (Inmarsat-A) No. Land - Ship (FELCOM) Example of Japan .............
Chapter 2 Loading a Recording Paper Prior to loading a Recording Paper, verify that the power is ON. DO NOT switch OFF during the loading. Procedure 1. Remove the Document Stacker. Recording Paper Type Code No. Qty K52 257 X 50M25TRU (For B4) 000-806-564 12 (1 set) K52 216 X 50M25TRU (For A4) 000-806-565 12 (1 set) 2. Open the Recording Paper Cover by pulling up the Recording Paper Cover Release Lever. Note: 1.
2. Connection Connect a modular plug to the "LINE" jack on the rear side of the PFX-50. See the figure below. Another modular plug should be connected to either the Junction Box via a modular jack box or the Communication Unit directly, depending on number of facsimile. For further details, refer to the Installation Manual of the FELCOM. 3. Changing dialing format Change dialing format from "pulse (dial)" to "pushbutton".
After connection is completed, attach the English language seal (supplied) to the front panel of the facsimile. Further, both the compass safe distance seal and Inmarsat "B" seal (supplied) should be attached to the facsimile. 4. Clearing contents of RAM To clear all contents of RAM, turn the power on while pressing and holding down the [1], [3] and [*] keys together. 5. Initial setting After clearing contents of RAM, display should look something like the figure shown below.
TABLE OF THE CHARACTER CODE FOR ENGLISH ALPHABET, SYMBOL LETTER 0 1 2 3 4 5 6 7 8 9 CODE 00 01 02 03 04 05 06 07 08 09 ° " -- , / : ( ) LETTER SPACE CODE 65 66 67 68 69 70 71 72 73 LETTER A B C D E F G H I J CODE 74 75 76 77 78 79 80 81 82 83 LETTER K L M N O P Q R S T CODE 84 85 86 87 88 89 90 91 92 93 LETTER U V W X Y Z CODE 94 95 96 97 98 99 6.
7. Setting Modem Speed, Turning Line Monitor On/Off Default settings Modem speed: Line monitor: 9600 bps Off 1. Turn the power on while pressing [1] and [3] keys to get into the test mode. Release the keys when the date appears. (Now you are in test mode.) 2. Press [FUNCTION/NO], [8], [FUNCTION/NO] (three times) and [AUTO RCV/YES] in that order. FUNCTION 0 = 00010010 3. Press 0, 0, 0, 1, 0, 0, 0, 0 in that order to change modem speed from 9600 bps to 2400 bps, 10: 9600 bps, 00: 2400 bps.