Operator's Manual

ManualsBrandsFuruno ManualsGPS receiverFuruno GP170

GPS NAVIGATOR

GP-170

OPERATOR'S MANUAL

www.furuno.com

Model

Summary of content (117 pages)

PAGE 1
OPERATOR'S MANUAL GPS NAVIGATOR Model GP-170 www.furuno.
PAGE 2
The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN All rights reserved. Printed in Japan A : JUN . 2014 Pub. No.
PAGE 3
IMPORTANT NOTICE General • This manual has been authored with simplified grammar, to meet the needs of international users. • The operator of this equipment must read and follow the descriptions in this manual. Wrong operation or maintenance can cancel the warranty or cause injury. • Do not copy any part of this manual without written permission from FURUNO. • If this manual is lost or worn, contact your dealer about replacement.
PAGE 4
SAFETY INSTRUCTIONS WARNING Indicates a condition that can cause death or serious injury if not avoided. CAUTION Indicates a condition that can cause minor or moderate injury if not avoided. Warning, Caution Prohibitive Action Mandatory Action CAUTION WARNING Do not disassemble or modify the equipment. The glass of an LCD panel breaks easily. Handle the LCD carefully. Fire, electrical shock or serious injury can occur. Injury can result if the glass breaks.
PAGE 5
TABLE OF CONTENTS FOREWORD................................................................................................................... vi SYSTEM CONFIGURATIONS....................................................................................... vii 1. OPERATIONAL OVERVIEW .................................................................................1-1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 2. Controls ......................................................................................................
PAGE 6
TABLE OF CONTENTS 4.1.1 How to preset the settings for routes ............................................................. 4-1 4.1.2 How to create a new route with the cursor and the ROUTE key.................... 4-3 4.1.3 How to create a new route from the route list ................................................ 4-4 4.2 How to Edit a Route ................................................................................................... 4-6 4.2.1 How to change the route name or color ................
PAGE 7
TABLE OF CONTENTS 9.4 9.5 9.6 9.7 9.8 9.9 9.10 9.3.3 How to set the positioning condition ...............................................................9-5 9.3.4 How to select the RAIM function ....................................................................9-6 9.3.5 How to select the datum .................................................................................9-7 9.3.6 How to set the initial position ..........................................................................9-7 9.3.
PAGE 8
FOREWORD A Word to the Owner of the GP-170 Congratulations on your choice of the FURUNO GP-170 GPS Navigator. We are confident you will see why the FURUNO name has become synonymous with quality and reliability. Since 1948, FURUNO Electric Company has enjoyed an enviable reputation for innovative and dependable marine electronics equipment. This dedication to excellence is furthered by our extensive global network of agents and dealers.
PAGE 9
SYSTEM CONFIGURATIONS Basic configuration is shown with solid line.
PAGE 10
SYSTEM CONFIGURATIONS Dual configuration Antenna Unit GPA-021S* Antenna Unit GPA-020S** Antenna Unit GPA-017S** Antenna Unit GPA-021S* Antenna Unit GPA-020S** Antenna Unit GPA-017S** *: w/internal beacon receiver **: w/o internal beacon receiver Switching Hub HUB-100 DISPLAY ROUTE GO TO MOB MARK EVENT 5 ON/OFF 6 1 4 2 ZOOM IN 7 CENTER 8 ZOOM OUT 9 ACK DELETE CURSOR BRILL ON/OFF 0 ROUTE GO TO MOB MARK EVENT 5 ON/OFF 6 1 4 2 3 PLOT ZOOM IN 7 CENTER 8 ZOOM OUT 9 ACK DELETE
PAGE 11
1. OPERATIONAL OVERVIEW 1.1 Controls 4 Operation keys 6 2 1 NU/CU ENT MENU ESC NU/CU ENT MENU ESC 3 LIST 5 LIST DISPLAY ROUTE GO TO MOB MARK EVENT 5 ON/OFF 6 ZOOM IN 7 CENTER 8 ZOOM OUT 9 ACK DELETE CURSOR BRILL 1 4 2 ON/OFF 0 3 7 DISPLAY ROUTE GO TO 8 MOB MARK EVENT 5 ON/OFF 6 PLOT 11 ZOOM IN 7 CENTER 8 ZOOM OUT 9 14 ACK DELETE CURSOR BRILL 17 1 PLOT 2 4 ON/OFF 0 3 10 13 18 Function keys 9 16 12 15 19 The keys are arranged according to the function.
PAGE 12
1. OPERATIONAL OVERVIEW No. Control 6 7 DISPLAY/1 ROUTE/2 8 GO TO/3 9 MOB/4 10 MARK EVENT/5 11 PLOT ON/OFF/ 6 ZOOM IN/7 CENTER/8 12 13 14 15 16 ZOOM OUT/9 CURSOR ON/OFF/ 0 ACK/DELETE 17 BRILL 18 19 (Power) USB port Function Menu screen • Selects and confirms the selected menu item. • Enters a numeric character. Display mode Selects the display mode. Starts/stops the registration of a route on the plotter display.
PAGE 13
1. OPERATIONAL OVERVIEW 1.2 How to Turn the Power On/Off Press the key to turn the power on. The start-up screen appears for 30 seconds then the last-used screen appears. Self test results Appears when internal beacon receiver is installed. Start-up screen XX: Program version numbers Last-used screen (example: plotter display) DGPS beacon receiver The GP-170 is available in two specifications, with DGPS beacon receiver and no DGPS beacon receiver.
PAGE 14
1.
PAGE 15
1. OPERATIONAL OVERVIEW Note 1: The default settings for night mode is 6 for [Display] and 7 for [Panel]. If the display is difficult to see when switching to the night mode, use the cursorpad (X) to increase the display brilliance. Note 2: Whenever the brilliance mode is changed, the last-used brilliance for the selected mode is set. Note 3: When the brilliance is preset, the background color is also preset (see paragraph 2.1.1).
PAGE 16
1. OPERATIONAL OVERVIEW Plotter Display Distance for RAIM reliability Spinner rotates when This icon appears the equipment is during the HDOP: 2D functioning normally. synchronization Status PDOP: 3D with ECDIS. Time and date of indication RAIM reliability Datum Position FIX This icon appears when the number of satellites used for positioning is more than four and the high precision speed computing is available.
PAGE 17
1.
PAGE 18
1. OPERATIONAL OVERVIEW Data Display Note: When invalid data is input, “- - - -” is displayed. 1.5 Main Menu Overview 1. Press the MENU/ESC key to open the main menu. These marks indicate additional menus. Basic operation or alert information 2. Use the cursorpad (S or T) to select a menu item then press the NU/CU ENT key. You can also select a menu item by pressing the numeric keys. This manual states this operating procedure as “Select [No. menu name].
PAGE 19
1. OPERATIONAL OVERVIEW 3. Select an option. 4. Press the MENU/ESC key to close the main menu. 1.6 List Overview The LIST key displays the mark list, route list and station list, in the sequence shown below. Any display Mark List Station List (Requires internal beacon receiver.) Route List : Short-press the LIST key : Long-press the LIST key How to save position in a list 1. Press the MENU/ESC key to open the main menu. 2. Select [8 System Setting] then [2 Plotter]. 3. Select [7 List Number]. 4.
PAGE 20
1. OPERATIONAL OVERVIEW How to change the data to display on the mark list 1. Press the MENU/ESC key to open the main menu. 2. Select [8 System Setting] then [2 Plotter]. 3. Select [8 List Information]. 4. Select [1 L/L] or [2 Range/Bearing]. [L/L]: Displays latitude and longitude. [Range/Bearing]: Displays the bearing and distance from own ship to a mark or a waypoint. 5. Press the MENU/ESC key to close the main menu. L/L 1.
PAGE 21
2. PLOTTER DISPLAY OVERVIEW, TRACK 2.1 How to Set the Display 2.1.1 How to select the background color You can select the background color to suit lighting conditions or environment (see section 1.3). 1. Press the MENU/ESC key to open the main menu. 2. Select [1 Display] then [1 Back Ground]. 3. Select [1 White] or [2 Black]. 4. Press the MENU/ESC key to close the main menu. 2.1.2 How to zoom in or out the display You can change the range scale on the plotter display.
PAGE 22
2. PLOTTER DISPLAY OVERVIEW, TRACK Course-up When the destination is set, the destination is at the top of the display and the north mark ( ) appears at the left side of the display. When the destination is not set, own ship's course is upward on the display at the moment you select the course-up and the north mark ( display. 2.1.4 ) appears at the left side of the How to turn the cursor on/off, change cursor size Press the CURSOR ON/OFF key to turn the cursor on or off.
PAGE 23
2. PLOTTER DISPLAY OVERVIEW, TRACK 2.1.7 How to center the cursor position or ship's position Cursor position 1. Press the CURSOR ON/OFF key to turn the cursor on. 2. Press the CENTER key. Ship's position 1. Press the CURSOR ON/OFF key to turn the cursor off. 2. Press the CENTER key. Note: When own ship reaches an edge of the display, own ship’s mark is automatically centered. 2.1.
PAGE 24
2. PLOTTER DISPLAY OVERVIEW, TRACK 3. Select [1 XTL Line]. 4. Select the XTL line color. To turn the XTL line off, select [8 Off]. 5. Press the MENU/ESC key to close the main menu. 2.1.10 How to show or hide the heading line and change its color You can show or hide the heading line and change its color. 1. Press the MENU/ESC key to open the main menu. 2. Select [1 Display] then [3 Lines Color]. 3. Select [2 Heading Line]. 4. Select the heading line color. To turn the heading line off, select [8 Off]. 5.
PAGE 25
2. PLOTTER DISPLAY OVERVIEW, TRACK 2.1.12 How to display the time mark You can display the time mark on the track every hour on the hour. Track T T T T 1. Press the MENU/ESC key to open the main menu. 2. Select [1 Display] then [4 Time Mark]. 3. Select the color for the time mark. To turn the time mark off, select [8 Off]. 4. Press the MENU/ESC key to close the main menu. 2.1.13 How to display the names for marks and waypoints You can display the names for marks and waypoints. 1.
PAGE 26
2. PLOTTER DISPLAY OVERVIEW, TRACK 2.2 Bearing Reference Ship’s course and bearing to a waypoint are displayed in true or magnetic bearing. Magnetic bearing is true bearing plus (or minus) earth’s magnetic variation. 2.2.1 How to select bearing reference The default setting displays true bearing. 1. Press the MENU/ESC key to open the main menu. 2. Select [8 System Setting] then [2 Plotter]. 3. Select [1 Bearing Reference]. 4. Select [1 True] or [2 Magnetic].
PAGE 27
2. PLOTTER DISPLAY OVERVIEW, TRACK 2.3 About Tracks The GP-170 stores 1,000 points of track. 2.3.1 How to start or stop plotting and recording of the track Press the PLOT ON/OFF key to start or stop plotting and recording of the track. The pop-up message "Resuming Track Plot" or "Stopping Track Plot" appears at the left side of the display for two seconds. When track plotting is stopped, the pears at the bottom left corner of the display. 2.3.
PAGE 28
2. PLOTTER DISPLAY OVERVIEW, TRACK 2.3.3 How to set the track color You can select the track color as follows: 1. Press the MENU/ESC key to open the main menu. 2. Select [2 Track/Mark] then [2 Track Color]. 3. Select the track color. 4. Press the MENU/ESC key to close the main menu. How to change the color of selected track 1. Put the cursor on the track. 2. Press the key to open the context menu. 3. Select [1 Change Color]. 4. Select the color to change. 5.
PAGE 29
3. MARKS You can put marks on the plotter display to indicate good fishing spot, location of traps, etc. Marks have 16 shapes and seven colors. Also, marks can be connected with lines. 3.1 How to Enter a Mark on the Plotter Display 3.1.1 How to preset mark appearance Set the default mark shape, color, line type to use when entering a mark. Mark shape You can select a mark shape from 16 types. 1. Press the MENU/ESC key to open the main menu. 2. Select [2 Track/Mark] then [3 Mark Shape]. 3.
PAGE 30
3. MARKS 2. Select [2 Track/Mark] then [5 Mark Line]. 3. Select the line type. • [None]: None • [Dash]: • [Solid]: • [Alternate Dash]: 4. Press the MENU/ESC key to close the main menu. When continuously entering marks by the method described in paragraph 3.1.2, the marks are connected with the selected line. Mark line color You can select a mark line color from seven colors. 1. Press the MENU/ESC key to open the main menu. 2. Select [2 Track/Mark] then [6 Line Color]. 3. Select the color. 4.
PAGE 31
3. MARKS 3. With the cursor on the [New] line, press the NU/CU ENT key. 4. Select [1 Cursor]. 5. Use the cursorpad to select the position for the mark. 6. Press the NU/CU ENT key. 7. Change the name (see page 4-6), position, symbol or color if necessary. 8. Select [9 Register]. The confirmation message appears. 9. Select [1 Yes] or [2 No]. [Yes]: Marks are registered with connection lines. [No]: Marks are registered without connection lines. 10. Press the MENU/ESC key to close the main menu.
PAGE 32
3. MARKS 4. Select [2 Input L/L]. 5. Enter latitude and longitude with the numeric keys. (To change the coordinate, select "N" or "E" then press one of keys from 0 to 9.) 6. Move the cursor to [Enter] then press the NU/CU ENT key. 7. Change the name (see page 4-6), position, symbol or color if necessary. 8. Select [9 Register]. The confirmation message appears. 9. Select [1 Yes] or [2 No]. [Yes]: Marks are registered with connection lines. [No]: Marks are registered without connection lines. 10.
PAGE 33
3. MARKS 3.2 How to Enter an Event Mark Event marks can be used to mark an important present position on the plotter display. 3.2.1 How to preset event mark appearance Set the default event mark shape and color to use when entering an event mark. Event mark shape You can select an event mark shape from 16 types. 1. Press the MENU/ESC key to open the main menu. 2. Select [2 Track/Mark] then [7 Event Mark]. 3. Use the cursorpad to select the shape then press the NU/CU ENT key. 4.
PAGE 34
3. MARKS 4. Select [3 OwnShip Position]. 5. Change the name (see page 4-6), position, symbol or color if necessary. 6. Select [9 Register]. The confirmation message appears. 7. Select [1 Yes] or [2 No]. [Yes]: Marks are registered with connecting lines. [No]: Marks are registered without connecting lines. 8. Press the MENU/ESC key to close the main menu. 3.3 How to Enter a MOB Mark on the Plotter Display The MOB mark denotes man overboard position. You can use it as an aid to rescue.
PAGE 35
3. MARKS 3.4 How to Edit a Mark or an Event Mark You can edit name, position, shape and color for a mark or an event mark on the plotter display or through the mark list. On the plotter display 1. Press the CURSOR ON/OFF key to turn the cursor on. 2. Use the cursorpad to select the (event) mark to edit then press the the context menu. key to open 3. Select appropriate options to edit then set them. 4. Press the MENU/ESC key to close the context menu. From the mark list 1.
PAGE 36
3. MARKS 3.5 How to Erase Marks You can erase a mark(s), an event mark(s) or a MOB mark. Note: You cannot erase the mark used as the current destination except the MOB mark. How to erase a mark from the context menu 1. Press the CURSOR ON/OFF key to turn the cursor on. 2. Use the cursorpad to select the mark to erase then press the context menu. key to open the 3. Select [2 Delete]. How to erase a mark with the ACK/DELETE key 1. Press the CURSOR ON/OFF key to turn the cursor on. 2.
PAGE 37
4. ROUTES To navigate from one place to another, several course changes are required. The point for course change is called a waypoint. The sequence of waypoints (marks for course changes) leading to the last destination is called a route. 4.1 How to Create a Route A maximum of 99 routes can be created and a route can have a maximum of 1,000 waypoints. 4.1.
PAGE 38
4. ROUTES Arrival radius You can receive an audiovisual notice when you are within the specified distance from a waypoint (see section 6.2). 1. Press the MENU/ESC key to open the main menu. 2. Select [8 System Setting] then [2 Plotter]. 3. Select [6 Initial XTL/Arrival/Stay]. 4. Select [2 Arrival Radius]. 5. Enter the arrival radius with the numeric keys (setting range: 0.001 to 9.999 NM). 6. Move the cursor to [Enter] then press the NU/CU ENT key. 7. Press the MENU/ESC key to close the main menu.
PAGE 39
4. ROUTES 2. Select [8 System Setting] then [2 Plotter]. 3. Select [6 Initial XTL/Arrival/Stay]. 4. Select [5 Departure Time]. 5. Enter the date and time departing from the starting point with the numeric keys. 6. Move the cursor to [Enter] then press the NU/CU ENT key. 7. Press the MENU/ESC key to close the main menu.
PAGE 40
4. ROUTES 4. Use the cursorpad to place the cursor on the location for the next waypoint then press the NU/CU ENT key. Repeat this step to enter all waypoints. 5. At the last waypoint, press the ROUTE key to complete the route. 4.1.3 How to create a new route from the route list With the cursorpad 1. Press the MENU/ESC key to open the main menu. 2. Select [3 Navigation] then [2 Route Registration]. 3. With the cursor on the [New] line, press the NU/CU ENT key. 4. Select [1 Cursor]. 5.
PAGE 41
4. ROUTES 7. Select [9 Add] to enter the waypoint. 8. Repeat steps 4 to 7 to enter all waypoints. 9. Press the MENU/ESC key to complete the route and close the main menu. By entering L/L 1. Press the MENU/ESC key to open the main menu. 2. Select [3 Navigation] then [2 Route Registration]. 3. With the cursor on the [New] line, press the NU/CU ENT key. 4. Select [2 Input L/L]. 5. Enter latitude and longitude for the first waypoint with the numeric keys.
PAGE 42
4. ROUTES 4.2 How to Edit a Route You can edit a route from the plotter display or through the route list. 4.2.1 How to change the route name or color From the route list 1. Press the MENU/ESC key to open the main menu. 2. Select [3 Navigation] then [2 Route Registration] to display the route list. 3. Use the cursorpad (S or T) or enter the route no. at the “Jump” position to select the route to edit then press the NU/CU ENT key. 4. To change the name, select [3 Name].
PAGE 43
4. ROUTES On the plotter display 1. Press the CURSOR ON/OFF key to turn the cursor on. 2. Put the cursor on any route line of the route to edit then press the context menu opens. key. The 3. Do steps 4 to 7 in "From the route list" on page 4-6 as appropriate. 4. Press the MENU/ESC key to close the context menu. 4.2.2 How to edit a waypoint in a route 1. Press the CURSOR ON/OFF key to turn the cursor on. 2.
PAGE 44
4. ROUTES 12. To change the staying time, select [5 STAY], then enter the staying time at the waypoint with the numeric keys. 13. Use the cursorpad to select [Enter] then press the NU/ CU ENT key. 14. To change the SOG, select [6 SOG], then enter the speed with the numeric keys. 15. Use the cursorpad to select [Enter] then press the NU/CU ENT key. 16. To change the departure time, select [7 DEP TIME], then enter the date and time departing from the waypoint with the numeric keys 17.
PAGE 45
4. ROUTES How to restore the skipped waypoint To restore the skipped waypoint if you have not passed it, do the following: 1. Press the CURSOR ON/OFF key to turn the cursor on. 2. Put the cursor on any route line of the route which contains the skipped waypoint then press the key to open the context menu. 3. Select [6 WPT List]. The ( ) icon is displayed on the skipped waypoint. Skipped waypoint 4. Use the cursorpad (S or T) to select the skipped waypoint then press the NU/CU ENT key. 5.
PAGE 46
4. ROUTES How to erase a waypoint with the ACK/DELETE key 1. Press the CURSOR ON/OFF key to turn the cursor on. 2. Use the cursorpad to select the waypoint to delete then press the ACK/DELETE key. The confirmation message appears. 3. Select [1 Yes]. How to erase a waypoint from the route list 1. Press the MENU/ESC key to open the main menu. 2. Select [3 Navigation] then [2 Route Registration]. 3. Use the cursorpad (S or T) to select the route no.
PAGE 47
4. ROUTES 4.2.6 How to change the route direction You can change the direction to travel a route. 1. Press the MENU/ESC key to open the main menu. 2. Select [3 Navigation] then [2 Route Registration] to show the route list. 3. Use the cursorpad (S or T) to select the route to change its direction then press the NU/CU ENT key to display the [Edit] window. This window can be opened as the context menu (see "On the plotter display" in paragraph 4.2.1). 4. Select [5 Forward/Reverse]. 5.
PAGE 48
4. ROUTES 4. Select [7 Route Copy]. "ROUTE1" is copied in the illustration below. [ROUTE1] is copied here. 5. Edit the route as appropriate (see section 4.2). 6. Press the MENU/ESC key to close the main menu. 4.3 How to Erase a Route How to erase a route from the context menu 1. Press the CURSOR ON/OFF key to turn the cursor on. 2. Put the cursor on any route line of the route to delete then press the open the context menu. key to 3. Select [2 Delete]. How to erase a route from the route list 1.
PAGE 49
5. DESTINATION Destination can be set five ways: by cursor, by waypoint, by mark, by route and by MOB position. The setting by MOB position is described in section 3.3. When setting a destination, a line (shortest course) appears between own ship and the destination selected.
PAGE 50
5. DESTINATION 4. Use the cursorpad to select [GoTo/Cancel] then press the NU/CU ENT key. Scroll bar (Indicates menus currently not shown in menu window. You can see the menus currently not shown by pressing the cursorpad ( or .)) 5.1.3 How to set a registered mark as a destination You can set a registered mark as a destination. From the main menu 1. Press the MENU/ESC key to open the main menu. 2. Select [3 Navigation] then [6 Goto (Mark Number)]. 3.
PAGE 51
5. DESTINATION 5.1.4 How to set a registered route as a destination You can set a registered route as a destination. From the main menu 1. Press the MENU/ESC key to open the main menu. 2. Select [3 Navigation] then [7 Goto (Route Number)]. 3. Enter the route number to set as a destination with the numeric keys. 4. Move the cursor to [Enter] then press the NU/CU ENT key. 5. Press the MENU/ESC key to close the main menu. From the context menu 1. Press the CURSOR ON/OFF key to turn the cursor on. 2.
PAGE 52
5. DESTINATION 5.2.3 How to cancel a destination from the context menu Note: This procedure is not available for the destination set with a mark (excluding the MOB mark). 1. Press the CURSOR ON/OFF key to turn the cursor on. 2. Use the cursorpad to place the cursor on a destination. 3. Press the key to open the context menu. On a route line On a waypoint On a MOB mark 4. For a route line or a waypoint, select [1 Yes] then [GoTo/Cancel]. For a MOB mark, select [1 GoTo/Cancel]. 5.
PAGE 53
5. DESTINATION 4. Move the cursor to [Enter] then press the NU/CU ENT key. [TTG (Manual)]: Time to go calculated by SOG set on page 4-2 [TTG (Estimated)]: Time to go calculated by actual SOG 5. Press the NU/CU ENT key then press the MENU/ESC key to close the main menu. 5.4 How to Display the ETA and TTG You can display the ETA and TTG to waypoints on the plotter display.
PAGE 54
5. DESTINATION 5.5 How to Calculate the Trip Distance You can calculate the trip distance as follows: 1. Press the MENU/ESC key to open the main menu. 2. Select [4 Notice Setting] then [4 Trip]. 3. Select [1 Status]. 4. Select [1 Stop], [2 Start/Restart] or [3 Clear]. [Stop]: Stops the trip distance calculation. [Start/Restart]*: Starts or restarts the trip distance calculation. [Clear]: Resets the trip distance. 5. Press the MENU/ESC key to close the main menu.
PAGE 55
6. NOTICES There are five notice conditions which generate both audio and visual notices: Arrival, Anchor, XTE, Ship Speed and Trip. When the conditions of a notice are met, the buzzer sounds according to the notice sound setting and the icon related to the notice turns from gray to blue at the top right-hand corner of the display. You can silence the buzzer by pressing the ACK/DELETE key.
PAGE 56
6. NOTICES 3. Select [1 Notice Sound]. 4. Select [1 Off], [2 On] or [3 Continuous]. [Off]: No sound, only visual notice (an icon turns blue) [On]: Three long beeps and visual notice (related icon turns blue) [Continuous]: This buzzer sounds until the ACK/DELETE key is operated to acknowledge the notice. Visual notice (related icon turns blue). 5. Press the MENU/ESC key to close the main menu. 6.2 Arrival/Anchor Notice Note: You can not set both arrival and anchor notices at the same time. 6.2.
PAGE 57
6. NOTICES 1. Press the MENU/ESC key to open the main menu. 2. Select [4 Notice Setting] then [1 Arrival/Anchor]. 3. Select [2 Anchor]. The anchor notice icon ( hand corner of the display. ) appears in gray at the top right- 4. Press the MENU/ESC key to close the main menu. To turn off the anchor notice, select [3 Off] at step 3. 6.
PAGE 58
6. NOTICES 4. Select [2 In] or [3 Out]. The ship speed notice icon ( ) appears in gray at the top right-hand corner of the display. [In]: The notice alerts you when your ship’s speed is within the range set. [Out]: The notice alerts you when your ship’s speed is lower or higher than the range set. 5. Select [2 Speed]. 6. Enter the minimum and maximum speeds with the numeric keys. 7. Move the cursor to [Enter] then press the NU/ CU ENT key. 8. Press the MENU/ESC key to close the main menu.
PAGE 59
7. DISPLAYS There are five display modes: PLOTTER, INTEGRITY, HIGHWAY, COURSE and DATA. This chapter describes the display modes except for PLOTTER. 7.1 Integrity Display The integrity display provides information about GPS satellite position, beacon station information and signal quality. There are four integrity displays: GNSS, beacon, graph for signal noise ratio and graph for satellite angle. Use the cursorpad (S or T) to change the displays, in the following sequence.
PAGE 60
7. DISPLAYS Elevation The area set on [Elevation Mask] is displayed in white. See "Satellite elevation" on page 9-5 for how to set elevation mask. Elevation mask is set to 10° Elevation mask is set to 30° Beacon The beacon display shows the beacon station information. Press the ◄ or ► key to select [Next 1]* or [Next 2]*.
PAGE 61
7. DISPLAYS Graph The graph displays show signal to noise ratio and satellite angle used for positioning for the last six hours.
PAGE 62
7. DISPLAYS 7.2 Highway Display The highway display provides a 3-D view of own ship’s progress toward destination. Use the cursorpad (W or X) to change the data at the right-hand of the display. North mark Waypoint Weather data (wind direction and speed) (See paragraph 2.1.14.) Attitude gauge (See page 9-3.) : Press the ► key. : Press the ◄ key. When weather data is received from the beacon station. When the data for roll, pitch or heave is received.
PAGE 63
7. DISPLAYS 7.3 Course Display The course display shows the course information. The information at the right-hand side of the display is different between autopilot connection and no autopilot connection.
PAGE 64
7. DISPLAYS 7.4 Data Display The data display shows the navigation data. Use the cursorpad (W or X) to change the data to display. Own ship’s position* Speed over ground Range Heading Course over ground Press the ◄ or ► key.
PAGE 65
7. DISPLAYS 3. Select [4 User Defined]. 4. Select [1 Custom 1]. • [TTG]: Time to go to destination • [TRIP]: Distance to go to destination • [TRIP TIME]: Time elapsed since the destination was set • [Route TTG]: Time to go to the final destination • [VTD]: Velocity to destination • [ETA/ETA(Plan)]: ETA is estimated time of arrival at destination. ETA(Plan) is planned estimated time of arrival at destination. 5. Select an option. 6. Repeat steps 4 and 5 to select options for [2 Custom 2] to [8 Custom 8].
PAGE 66
7. DISPLAYS How to zoom information 1. Press the CURSOR ON/OFF key. An information is highlighted as follows. An information highlighted 2. Use the cursorpad (S or T) to select the information to zoom in. SOG is highlighted in the following example. 3. Press the ZOOM IN key to zoom in the SOG information. To go to the original display, press the ZOOM OUT key. 4. Press the CURSOR ON/OFF key to deselect the SOG information.
PAGE 67
8. ALERTS “Alert” is a generic name for a notice to any unusual or potentially dangerous situation generated within the system. There are two types of alerts, warning and caution. Warning: Conditions or situations which require immediate attention for precautionary reasons. Caution: Awareness of a condition which continues to require attention out of the ordinary consideration of the situation. 8.
PAGE 68
8. ALERTS ID 213 Message Loss of differential signal. Type Caution 215 Abbreviated messages: Loss of DGNSS signal. Differential integrity status. Meaning More than 10 seconds have passed since the last beacon message is received. Caution The beacon station selected automatically is unhealthy. Abbreviated messages: DGNSS integrity status. Antenna short-circuited. Warning The antenna has shorted out.
PAGE 69
8. ALERTS Alert category Type Warning Circle Icon Caution Square Visual indication • Acknowledged: Yellow-orange • Not acknowledged: Yellow-orange, flashing Yellow For details, see page AP-8. 8.2 Alert List The alert list shows all currently violated alerts and state of acknowledgment. All unacknowledged alerts are shown, even those whose reason for alert has passed (except for a caution). 1. Press the MENU/ESC key to open the main menu. 2.
PAGE 70
8. ALERTS 8.3 Alert Log The alert log shows the latest 50 alerts. When the log becomes full, the oldest entry is erased to make room for current alerts. 1. Press the MENU/ESC key to open the main menu. 2. Select [5 Alert] then [4 Alert Log] to show the alert log. Priority Alert name Alert number Date and time of acknowledgement Date and time of occurrence Date and time when occurrence factor is gone Position of occurrence List no. 3. Press the MENU/ESC key to close the alert log. 8.
PAGE 71
9. OTHER FUNCTIONS This chapter describes menu items not described in other chapters. 9.1 Unit Setup Menu You can set the units of measurement for distance, depth and water temperature. 1. Press the MENU/ESC key to open the main menu. 2. Select [8 System Setting] then [3 Unit Setup]. 3. Distance: Select [1 Unit of Distance]. Depth: Select [2 Unit of Depth]. Water temperature: Select [3 Unit of Temperature]. Distance Depth Water temperature 4. Select the unit. 5.
PAGE 72
9. OTHER FUNCTIONS 3. Select [1 Position Offset]. 4. Enter the offset value with the numeric keys. Mark your ship’s position on the chart to calculate the error with latitude and longitude, and enter the values. To change the coordinate, select "N" or "E" then press one of keys from 0 to 9. 5. Move the cursor to [Enter] then press the NU/CU ENT key. 6. Press the MENU/ESC key to close the main menu. Note: When you set the position offset, the Datum indication changes to 999 (User Defined).
PAGE 73
9. OTHER FUNCTIONS Ship size and antenna position 1. Press the MENU/ESC key to open the main menu. 2. Select [8 System Setting] then [4 Correction, Offset]. 3. Select [3 Ship Size/Antenna Position]. 1 2 1 : Set the width and length of your ship. Enter the values as correct as possible because these values influence the output sentence “POS”. Note that these values are the upper limits for the values of 2 . 2 : Set the mounting location for the antenna unit.
PAGE 74
9. OTHER FUNCTIONS 9.3 GNSS Menu 9.3.1 How to select the positioning system 1. Press the MENU/ESC key to open the main menu. 2. Select [8 System Setting] then [5 GNSS]. 3. Select [1 Method]. 4. Select [1 GPS]. 5. Press the MENU/ESC key to close the main menu. 9.3.2 No. 2, 3 and 4 are reserved for future use.
PAGE 75
9. OTHER FUNCTIONS 3. Select [2 GPS Smoothing]. 4. Select [1 Position], [2 Speed] or [3 Speed Average]. 5. Enter the time for smoothing with the numeric keys. 6. Move the cursor to [Enter] then press the NU/ CU ENT key. 7. Press the MENU/ESC key to close the main menu. 9.3.3 How to set the positioning condition Satellite elevation You can set the minimum elevation of satellites to use to fix position. 1. Press the MENU/ESC key to open the main menu. 2. Select [8 System Setting] then [5 GNSS]. 3.
PAGE 76
9. OTHER FUNCTIONS 4. Select [2 Not Used GPS]. 5. Enter the satellite numbers with the numeric keys. 6. Move the cursor to [Enter] then press the NU/ CU ENT key. 7. Press the MENU/ESC key to close the main menu. Core filter 1. Press the MENU/ESC key to open the main menu. 2. Select [8 System Setting] then [5 GNSS]. 3. Select [3 Condition]. 4. Select [5 Core Filter]. 5. Select [1 No] or [2 Yes].
PAGE 77
9. OTHER FUNCTIONS 6. Select [2 Accuracy Level]. 7. Enter the distance with the numeric keys. 8. Move the cursor to [Enter] then press the NU/ CU ENT key. 9. Press the MENU/ESC key to close the main menu. 9.3.5 How to select the datum Your unit is programmed to recognize most of the major chart systems of the world. Although the WGS84 system, the GPS standard, is now widely used other categories of charts still exist. Select the same datum which is used in your nautical charts.
PAGE 78
9. OTHER FUNCTIONS 9.3.7 How to set the positioning cycle You can set the positioning cycle. Position is updated faster with the 5Hz or 10Hz setting, however the accuracy may not be as good as with the 1Hz setting. It is recommended to use the 1Hz setting for vessels other than high speed craft. 1. Press the MENU/ESC key to open the main menu. 2. Select [8 System Setting] then [5 GNSS]. 3. Select [9 Cycle]. 4. Select [1 1Hz], [2 5Hz] or [3 10Hz]. The confirmation message appears. 5. Select [1 Yes].
PAGE 79
9. OTHER FUNCTIONS 9.4 Beacon/SBAS Menu This menu sets the beacon and SBAS. 9.4.1 How to select the differential corrections to use 1. Press the MENU/ESC key to open the main menu. 2. Select [8 System Setting] then [6 Beacon/SBAS]. 3. Select [1 Mode]. 4. Select an option. [GNSS]: Uses neither beacon nor SBAS for positioning. [GNSS+SBAS (+QZSS)]: Uses SBAS and QZSS. [GNSS+Internal Beacon]*: Uses internal beacon. [GNSS+Beacon (Data1, Data2 or Data4)]*: Uses external beacon.
PAGE 80
9. OTHER FUNCTIONS 5. Enter the satellite number with the numeric keys (setting range: 120 to 138). 6. Move the cursor to [Enter] then press the NU/ CU ENT key. 7. Press the MENU/ESC key to close the main menu. Beacon 1. Press the MENU/ESC key to open the main menu. 2. Select [8 System Setting] then [6 Beacon/SBAS]. 3. Select [3 Beacon Station]. 4. Select [1 Auto], [2 Set Parameter] or [3 Select Station ID]. [Auto]: Automatically selects the nearest station among available stations. Go to step 8.
PAGE 81
9. OTHER FUNCTIONS 3. Select [4 Station Database] to show the [Station List] for 1020 station data. Enter the station no. (e.g. “0001”) with the numeric key then press the NU/CU ENT key to display the information of the selected station at the right side of the screen. 4. Press the MENU/ESC key to close the main menu. Registered stations You can register up to 20 beacon stations. Note: This menu requires the internal beacon receiver. 1. Press the MENU/ESC key to open the main menu. 2.
PAGE 82
9. OTHER FUNCTIONS 4. Use the cursorpad (S or T) to select ID no. then press the NU/CU ENT key. 5. Edit the name, position, frequency or bit rate. 6. Press the MENU/ESC key to close the main menu. Disable satellite You can disable a maximum of three satellites. 1. Press the MENU/ESC key to open the main menu. 2. Select [8 System Setting] then [6 Beacon/SBAS]. 3. Select [6 Not Used Satellite]. 4. Select [1 SBAS] or [2 QZSS]. 5.
PAGE 83
9. OTHER FUNCTIONS 9.6 I/O Menu Besides its fundamental function of displaying position, the GP-170 can also output various data to external equipment. Before outputting data to external equipment, first determine what data the external equipment requires. Output only necessary data to ensure data will be output correctly. All data transmitted by marine electronics equipment are prefixed with a two character code called a talker.
PAGE 84
9. OTHER FUNCTIONS 10. Select [4 BPS]. 11. Select [1 4800 bps], [2 9600 bps] or [3 38400 bps]. 12. Select [5 Sentence]. 13. Use the cursorpad to select the sentence then press the NU/CU ENT key. 14. Use the cursorpad (W or X) to select the TX interval. TX interval is available in [- -] (off), [0.1s]*, [0.2s]*, [1s], [2s], [3s], [4s], [5s], [6s], [10s], [15s], [20s], [30s], [60s] and [90s]. *: Only for GGA, GLL, GNS, RMC and VTG when selecting [38400 bps] at step 11. 15. Press the NU/CU ENT key.
PAGE 85
9. OTHER FUNCTIONS 6. Press the NU/CU ENT key. Note: For the TX interval of [0.1s] or [0.2s], set the positioning cycle (refer to paragraph 9.3.7) as follows: • For [0.1s], set the positioning cycle at 10Hz. • For [0.2s], set the positioning cycle at 5Hz or 10Hz. 7. Press the MENU/ESC key to close the sentence window. 8. Press the MENU/ESC key to open the main menu. 9. Select [7 I/O] then [5 Ethernet]. 10. Select [2 IP ADR /Port]. 11.
PAGE 86
9. OTHER FUNCTIONS 5. When selecting [5 Ethernet], do the following: 1) Press the ACK/DELETE key to move the cursor to the leftmost of the input position. Press the ACK/DELETE key. Backspace 2) Enter the Ethernet SFI with the cursorpad and the numeric keys (combination of two alphabets and four numerals). SFI (System Function ID) is an identification code used by the system. 3) Move the cursor to [Enter] then press the NU/CU ENT key. Go to step 9. Note: Set the SFI to eliminate overlap with other ones.
PAGE 87
9. OTHER FUNCTIONS 3. Select [Data1] (or 2, 3, 4). $YCMTW,027.32,C$GPZDA,012614.00,01,11,2012,09,00 42 $YCMTW,027.32,C$GPZDA,012614.00,01,11,2012,09,00 42 $YCMTW,027.32,C$GPZDA,012614.00,01,11,2012,09,00 42 $YCMTW,027.32,C$GPZDA,012614.00,01,11,2012,09,00 42 $YCMTW,027.32,C$GPZDA,012614.00,01,11,2012,09,00 42 $YCMTW,027.32,C$GPZDA,012614.00,01,11,2012,09,00 42 $YCMTW,027.32,C$GPZDA,012614.00,01,11,2012,09,00 42 $YCMTW,027.32,C$GPZDA,012614.00,01,11,2012,09,00 42 $YCMTW,027.32,C$GPZDA,012614.
PAGE 88
9. OTHER FUNCTIONS 9.7 How to Set Dual Configuration You can configure two dual differential GPS navigator systems and an interface unit. 1. Press the MENU/ESC key to open the main menu. 2. Select [7 I/O] then [8 Dual]. 3. Select [1 No], [2 Serial (Data2)] or [3 Ethernet]. [No]: Don’t set dual configuration. [Serial (Data2)]: Sets dual configuration using data2. [Ethernet]: Sets dual configuration using Ethernet. 4. Press the MENU/ESC key to close the main menu. 9.
PAGE 89
9. OTHER FUNCTIONS 10. Select [1 Mode]. 11. Select [2 On]. Note: When selecting [2 On], you can not set a destination on the GP-170. 12. Press the MENU/ESC key to close the main menu. To turn the synchronization off, select [1 Off] at step 11. Note 1: When selecting [1 Off] during the synchronization with the ECDIS, the destination is canceled on the GP-170. Note 2: The GP-170 uses waypoint information from the ECDIS when they are synched to one another.
PAGE 90
9. OTHER FUNCTIONS 9.10 How to Set the Demo Mode A demo mode, which shows internally generated navigation data, is provided to acquaint you with the features of the GP-170. You can set the demo mode as follows: 1. Press the MENU/ESC key to open the main menu. 2. Select [8 System Setting] then [8 Demo]. 3. Select [1 Parameter]. 4. Enter each setting with the numeric keys refer to the left figure. [Date]: Set the starting date and time in UTC. [Position]: Set the starting position.
PAGE 91
10. MAINTENANCE, TROUBLESHOOTING NOTICE Do not apply paint, anti-corrosive sealant or contact spray to plastic parts or equipment coating. Those items contain products that can damage plastic parts and equipment coating. 10.1 Maintenance Regular maintenance is important to maintain performance. Check the following points to help maintain performance. • Check that connectors on the rear panel are firmly tightened and free of rust.
PAGE 92
10. MAINTENANCE, TROUBLESHOOTING 10.2 Fuse Replacement WARNING Use the proper fuse. A wrong fuse can damage the equipment and cause fire. The fuse (type: FGBO-A 125V 3A PBF, code no.: 000-155-850-10) in the power cable protects against overvoltage and equipment trouble. If you cannot turn on the power, first check the fuse. If the fuse has blown, replace the fuse with the specified fuse. If the fuse blows again after replacement, contact your dealer. 10.
PAGE 93
10. MAINTENANCE, TROUBLESHOOTING 10.4 Equipment Information You can display information about this equipment from the menu. 1. Press the MENU/ESC key to open the main menu. 2. Select [6 Maintenance] then [1 Information]. X: Board version no. XX: Program version no. 3. Select [1 Main], [2 Panel], [3 GPS], [4 Beacon] (requires internal beacon receiver) or [5 Database]. GPS Main Panel Beacon Database 4. Press the NU/CU ENT key to close each information window. 5.
PAGE 94
10. MAINTENANCE, TROUBLESHOOTING 10.5 Self Test The self test checks the ROM, RAM, input/output data, GPS core, Beacon core, keyboard and LCD performance. The user can do the tests to help the service technician in troubleshooting. Memory test 1. Press the MENU/ESC key to open the main menu. 2. Select [6 Maintenance] then [2 Self Test]. 3. Select [1 Memory Test]. The test results are displayed as "OK", "NG" (No Good) or "– –". If any NG is displayed, contact your dealer.
PAGE 95
10. MAINTENANCE, TROUBLESHOOTING Keyboard test 1. Press the MENU/ESC key to open the main menu. 2. Select [6 Maintenance] then [2 Self Test]. 3. Select [2 Keyboard Test]. 4. Press each key one by one. A key's corresponding location on the display turns blue if the key is normal. 5. Press the MENU/ESC key three times to close the keyboard test window. LCD test 1. Press the MENU/ESC key to open the main menu. 2. Select [6 Maintenance] then [2 Self Test]. 3. Select [3 LCD Test].
PAGE 96
10. MAINTENANCE, TROUBLESHOOTING 4. Press the NU/CU ENT key. Each press of this key changes the LCD pattern in the sequence shown below. Black White Red Green Blue Checker board RGB gradation Operation instructions display Note: You can cancel the test at any time by pressing the MENU/ESC key. 5. Press the MENU/ESC key to close the test pattern window. Automatic test The memory, keyboard and LCD tests are automatically tested. 1. Press the MENU/ESC key to open the main menu. 2.
PAGE 97
10. MAINTENANCE, TROUBLESHOOTING 4. Select [1 Backup User Setting], [2 Load User Setting], [3 Import GPX (Overwrite)], [4 Import GPX (Addition)] or [5 Export GPX]. [Backup User Setting]: Saves the current settings to a USB flash memory. [Load User Setting]: Loads the saved settings from a USB flash memory. [Import GPX (Overwrite)]: Imports the GPX data (marks, waypoints and routes) from a USB flash memory. The GPX data in the GP-170 are deleted.
PAGE 98
10. MAINTENANCE, TROUBLESHOOTING 10.7 How to Clear the Memory You can clear display setting, GPS memory, marks and routes to start afresh. 1. Press the MENU/ESC key to open the main menu. 2. Select [8 System Setting] then [9 Clear Memory]. 3. Select [1 Clear Display Setting], [2 Clear GPS], [3 Clear All] or [4 Clear Mark&Route]. [Clear Display Setting]: Clears the display setting. [Clear GPS]: Clears the GPS memory. [Clear All]: Clears both display setting and GPS memory.
PAGE 99
APPENDIX 1 MENU TREE Note: If setting invalid data in numerical entry, two beeps sound. Reenter the correct data.
PAGE 100
APPENDIX 1 MENU TREE 1 ├ Trip │ ├ Status (Stop , Start/Restart, Clear) │ └ Range (Open the setting window.) Sound └ ├ Notice Sound (Off , On, Continuous) └ Key Sound (On , Off) 5 Alert ├ ├ ├ └ Active Alert (Open the active alert list.) Mode*2 (Alert I/F 1 , Alert I/F 2, Legacy) Remote Ack I/F*2 (Ack , BuzzerStop) Alert Log (Open the alert log.) *2: For serviceman. 6 Maintenance ├ Information │ ├ Main (Open the information for main board.) │ ├ Panel (Open the information for panel board.
PAGE 101
APPENDIX 1 MENU TREE 1 ├ │ │ │ │ ├ │ │ │ │ ├ │ │ │ │ │ │ │ └ Ethernet ├ Sentence (Options are same as Output Data1 excluding APA, Rnn and WNR.) ├ IP ADR/Port (Open the entry window.) ├ MP (Enable, Disable ) └ MP IP ADR/Port (Open the entry window.
PAGE 102
APPENDIX 1 MENU TREE 1 ├ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ ├ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ ├ │ │ │ │ ├ │ └ GNSS ├ ├ │ │ │ ├ │ │ │ │ │ ├ │ │ ├ ├ ├ ├ ├ └ Method (GPS , GLONASS*3, GALILEO*3, Multi*3) GPS Smoothing ├ Position (Open the setting window.) ├ Speed (Open the setting window.) └ Speed Average (Open the setting window.) Condition ├ Elevation Mask (Open the setting window.) ├ Not Used GPS (Open the setting window.) *3: Reserved for ├ Not Used GLONASS*3 (Open the setting window.
PAGE 103
APPENDIX 2 LIST OF TERMS/SYMBOLS The following table shows the terms and symbols used in the GP-170.
PAGE 104
APPENDIX 2 LIST OF TERMS/SYMBOLS Terms EQUIP ERR ETA EVENT EXT FEB FIX FREQ FULL GC GCD GLONASS GND GNSS GPS GPX GRID HDG HDOP HL H UP ID IEC IN IND INFO INP INT I/O JAN JUL JUN LAT L/L LOG LON MAG MAN MAR MAY MENU MIN MOB MSTR N NAV NMEA NOV NT AP-6 Meaning Equipment Error Estimated Time of Arrival Event External February Fix Frequency Full Great Circle Great Circle Distance Global Opening Navigation Satellite System Ground Global Navigation Satellite System Global Positioning System GPS eXchange Format
PAGE 105
APPENDIX 2 LIST OF TERMS/SYMBOLS Terms NTP NU OCT OFFSET ON OS OUT PDOP POSN PRN PWR QZSS RAIM REF RL RLD RM RMS RNG ROT ROUTE Rx, RX S SAT SBAS SEL SEP SET SIM SNR SOG SPD SST STN STW SV SYM T TCPA TIME TM TOA TOD TTG UTC VAR VECT VTD W Meaning Network Time Protocol North Up October Offset On Own Ship Out/Output Positional Dilution Of Precision Position Pseudo-Random-Noise Power Quasi-Zenith Satellite System Receiver Autonomous Integrity Monitoring Reference Rhumb Line Rhumb Line Distance Relative Motion
PAGE 106
APPENDIX 2 LIST OF TERMS/SYMBOLS Terms WARNING WAT WER WGS WPT XTD XTL XTE Meaning Warning Water Word Error Rate World Geodetic System Waypoint Cross (=X) Track Distance Cross (=X) Track Limit Cross (=X) Track Error Symbols Symbols Meaning Marks Cursor (Left: Large size, Right: Small size) Own ship MOB (Man Overboard) mark North mark Chart mode (The cursor is turned off.) Cursor mode (The cursor is turned on.
PAGE 107
APPENDIX 3 TIME DIFFERENCES AP-9
PAGE 108
APPENDIX 4 GEODETIC CHART LIST 001: 002: 003: 004: 005: 006: 007: 008: 009: 010: 011: 012: 013: 014: 015: 016: 017: 018: 019: 020: 021: 022: 023: 024: 025: 026: 027: 028: 029: 030: 031: 032: 033: 034: 035: 036: 037: 038: 039: 040: 041: 042: 043: 044: 045: 046: 047: 048: 049: 050: 051: 052 053: 054: 055: 056: 057: 058: 059: 060: 061: 062: 063: 064: 065: 066: 067: 068: 069: 070: 071: 072: 073: 074: 075: 076: 077: 078: 079: 080: 081: 082: 083: 084: 085: 086: 087: 088: 089: 090: WGS84 WGS72 TOKYO NORTH AMERICA
PAGE 109
APPENDIX 5 WHAT IS SBAS? A satellite based augmentation system, or SBAS (Satellite Based Augmentation System), is an augmentation system that uses additional messages from satellite broadcasts to support regional and wide area augmentation. SBAS provides GPS signal corrections to SBAS users, for even better position accuracy, through the GPS error corrections that are widely broadcasted from the geostationary satellite. SBAS is used in America, Europe, Japan and India.
PAGE 110
APPENDIX 6 PARTS LIST/LOCATION Parts list This equipment contains complex modules in which fault diagnosis and repair down to component level are not practical (IMO A.694(17)/8.3.1). Only some discrete components are used. FURUNO Electric Co., Ltd. Believes identifying these components is of no value for shipboard maintenance; therefore, they are not listed in this manual. Major modules can be located on the parts location photos below. ELECTRICAL PARTS LIST Unit Display Unit GP-170 Code No.
PAGE 111
FURUNO GP-170 SPECIFICATIONS OF GPS NAVIGATOR GP-170 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 GPS RECEIVER Receiving frequency 1575.42 MHz Tracking code C/A code Number of channel GPS: 12 channels parallel, 12 satellites Accuracy (dependent on ionospheric activity and multipath) GPS 10 m approx. (2drms, HDOP<4) DGPS 5 m approx. (2drms, HDOP<4) WAAS 3 m approx. (2drms, HDOP<4) MSAS 7 m approx. (2drms, HDOP<4) Ship’s speed accuracy 0.
PAGE 112
FURUNO GP-170 3 3.1 3.2 3.3 3.4 DGPS BEACON RECEIVER (for DGPS model) Frequency range 283.5 kHz to 325.0 kHz Channel separation 500 Hz MSK rate 25, 50, 100, 150, 200 bps Operation mode Auto or manual 4 INTERFACE 4.1 Number of ports 4.2 4.3 Data format Data port 1, 2 and 4 IEC/NMEA Mode IN: OUT: RTCM Mode IN/ OUT: 4.4 4.5 4.6 Serial: 4 ports (IEC61162-1 I/O: 2, O: 1, IEC61162-2 I/O: 1), Ethernet (IEC61162-450):1 port, USB: 1 port IEC61162-1 Ed.3/4, NMEA0183 Ver1.5/2.0/4.
PAGE 113
FURUNO 5 5.1 5.2 6 6.1 POWER SUPPLY Display unit Rectifier (option) PR-240 PR-62 GP-170 12-24 VDC: 0.8-0.4 A (w/ internal beacon receiver) 100-115/220-230 VAC, 1 phase, 50/60Hz 100/110-115/220/230 VAC, 1 phase, 50/60Hz 6.4 ENVIRONMENTAL CONDITIONS Ambient temperature Antenna unit -25°C to +70°C Display unit -15°C to +55°C Relative humidity 95% or less at +40°C Degree of protection Antenna unit IP56 Display unit IP25 (USCG CFR-46), IPX0 (USB port cover opened) Vibration IEC 60945 Ed.4 7 7.1 7.
PAGE 114
FURUNO GP-170 This page is intentionally left blank.
PAGE 115
INDEX A Alerts acknowledging ........................................ 8-4 list ............................................................ 8-3 log ........................................................... 8-4 overview .................................................. 8-1 Antenna position ....................................... 9-3 Anti-multipath mode .................................. 9-8 Attitude gauge ........................................... 9-3 H Heading line on/off ..............................
PAGE 116
INDEX presetting .................................................4-1 S Satellite elevation .......................................9-5 SBAS ............................................ 9-9, AP-11 Self test ....................................................10-4 Ship size ....................................................9-3 Station data ..............................................9-10 Symbols ..................................................AP-8 System configurations.................................
PAGE 117