The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN All rights reserved. Printed in Japan A : JUN . 2012 F : FEB . 02, 2015 Pub. No.
IMPORTANT NOTICES General • This manual has been authored with simplified grammar, to meet the needs of international users. • The operator of this equipment must read and follow the descriptions in this manual. Wrong operation or maintenance can cancel the warranty or cause injury. • Do not copy any part of this manual without written permission from FURUNO. • If this manual is lost or worn, contact your dealer about replacement.
SAFETY INSTRUCTIONS The operator must read the safety instructions before attempting to operate the equipment. WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. Warning, Caution Prohibitive Action WARNING Do not open the equipment. The equipment uses high voltage that can cause electrical shock.
SAFETY INSTRUCTIONS CAUTION Do no turn on the equipment with the transducer out of water. The transducer can be damaged. The picture is not refreshed when picture advancement is stopped. Maneuvering the vessel in this condition can result in a dangerous situation. Adjust the gain correctly. Incorrect gain may give a wrong depth indication, which could result in a dangerous situation. The data presented by this equipment is intended as a source of navigation information.
TABLE OF CONTENTS FOREWORD ...................................................................................................................ix SYSTEM CONFIGURATION ..........................................................................................xi EQUIPMENT LISTS .......................................................................................................xii 1. OPERATIONAL OVERVIEW .................................................................................1-1 1.1 Controls........
TABLE OF CONTENTS 3. POINTS ..................................................................................................................3-1 3.1 What is a Point? .........................................................................................................3-1 3.2 How to Enter a Point...................................................................................................3-1 3.2.1 How to enter a point at the current position....................................................
TABLE OF CONTENTS 6. MAP SETTINGS, 2D PERSPECTIVE/3D DISPLAYS AND SATELLITE OVERLAY..........................................................................................6-1 6.1 Map Setup.................................................................................................................. 6-1 6.2 2D Perspective Display .............................................................................................. 6-5 6.3 3D Display.............................................................
TABLE OF CONTENTS 8. ALARMS ................................................................................................................8-1 8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 8.10 8.11 8.12 8.13 9. ALARMS Menu...........................................................................................................8-1 Audio Alarm Conditions ..............................................................................................8-2 Arrival Alarm ................................................
TABLE OF CONTENTS 11. CUSTOMIZING YOUR UNIT................................................................................11-1 11.1 GENERAL Menu ...................................................................................................... 11-1 11.2 PLOTTER Menu....................................................................................................... 11-2 11.3 SYSTEM Menu ........................................................................................................ 11-3 12.
FOREWORD A Word to GP-1670F, GP-1870F Owners Congratulations on your choice of the FURUNO GP-1670F, GP-1870F GPS Plotter/Sounder. We are confident you will see why the FURUNO name has become synonymous with quality and reliability. Since 1948, FURUNO Electric Company has enjoyed an enviable reputation for innovative and dependable marine electronics equipment. This dedication to excellence is furthered by our extensive global network of agents and dealers.
FOREWORD Fish finder • Fish finder measures the depth to the bottom and displays underwater conditions in multi-colors* according to echo strength. A monochrome presentation shows the echoes in shades of gray. (*Number of colors depends on network sounder, color sounder.). • Automatic and manual fish finder operation. Auto mode automatically adjusts range, gain and clutter according to purpose - fishing or cruising. • Wide variety of zoom modes for detailed observation of fish and bottom.
SYSTEM CONFIGURATION The environmental category of each unit is as follows: Unit Environmental category Display unit Protected from the weather GPS antenna unit Exposed to the weather, or protected from the weather in case of internal antenna Transducer, sensor Submerged in water Other units Protected from the weather GP-1670F Antenna Unit GPA-017 or GPA-017S Water temp./speed sensor ST-02MSB, ST-02PSB Water temp.
EQUIPMENT LISTS Standard supply Name Type Code no. Qty Select one Remarks Display Unit GP-1670F - Display Unit GP-1870F - Installation Materials CP14-07100 000-021-070 1 set Spare Parts SP14-03501 001-184-710 1 set Accessories FP14-03001 001-184-730 1 set For GP-1670F FP14-03201 001-183-120 1 set For GP-1870F w/CP14-07101, MJ-A3SPF0013A035C (power cable) Optional equipment Name Type Code no.
EQUIPMENT LISTS Name Type Code no. Remarks Temperature Sensor T-04MSB 000-026-893 Thru-hull type T-04MTB 000-026-894 Transom mount Matching Box MB-1100 000-041-353 For connection to 1 kW transducer Rectifier PR-62 000-013-484 100 VAC Rectifier PR-62 000-013-485 110 VAC Rectifier PR-62 000-013-486 220 VAC Rectifier PR-62 000-013-487 230 VAC Junction Box FI-5002 Right Angle Mounting Base No.13QA330 001-111-910-10 L-angle Mounting Base No.
EQUIPMENT LISTS Name Type Code no. Remarks Micro style, female, termination resistor Termination Resistor (Micro) LTWMC-05BFFTSL8001 000-168-605-10 Inline Terminator FRU-0505-FF-IS 001-077-830-10 Cable Assy. 02S4147-1 000-141-082 For speed/temp.
1. OPERATIONAL OVERVIEW 1.1 Controls 1.1.1 Control description The controller for this system is either the GP-1670F or the GP-1870F. A key that has two text labels has two functions. The top label is the main function and the bottom label is the secondary function. Short-push to access the main function and long-push (approximately three seconds) to access the secondary function.
1. OPERATIONAL OVERVIEW Control Description Short push: Display the base RotoKey soft controls for the current RotoKey mode. Long push: Display the full RotoKey soft controls for the current mode. Rotate: Zoom in or out the display width. Select a menu item. Select the display range for the fish finder. POINTS/GO Short press: Put a point at the cursor position. TO key Long press: Set cursor position as destination. EVENT/ Short press: Put a point at the current position.
1. OPERATIONAL OVERVIEW Tested SD cards The SD cards tested for use in this equipment are listed in the table below.
1.
1. OPERATIONAL OVERVIEW 1.2 RotoKeyTM and Soft Controls The main function of the RotoKeyTM is to display the RotoKey menu, a set of revolving soft controls that change with the operating mode. There are two sets of RotoKey menus: base and full. A short push of the key shows the base set for the current mode, and a long push displays the full compliment of soft controls for the current mode. When the full set is active, a scroll bar appears to show your location in the menu.
1. OPERATIONAL OVERVIEW 1.3 How to Turn the Power On or Off To turn the power ON, press approx two seconds. Release when the FURUNO logo appears. It takes approx. 25-30 seconds to start the system, in the sequence shown below. 1) If some data is missing or is out of date, a message states the missing component. Contact your dealer for details. 2) If a C-MAP by Jeppesen chart card is inserted, chart information is checked to see if it is up to date.
1. OPERATIONAL OVERVIEW 2D plotter display, vector chart A vector chart is a series of points and lines that make up the features on a chart. Vector charts look computer generated. Details on the chart can be turned on and off. Objects on the chart can be clicked on to learn more details. Depths can be monitored to warn before grounding. When zooming in and out of a vector chart only the geographical features grow larger or smaller where text keeps it's same size and orientation.
1. OPERATIONAL OVERVIEW 2D plotter display, vector/satellite The vector chart plus a satellite photo. See chapter 6 for how to adjust the satellite display. 2D plotter display, raster A raster chart is a direct copy or scan of an existing paper chart. Raster charts look identical to paper charts. All information contained within the chart is printed directly on it. What you see is what you get. When zooming in and out of a raster chart everything on the chart grows larger or smaller.
1. OPERATIONAL OVERVIEW 1.6 The Cursor The cursor has the functions shown below. • Find, when put on respective item: • Position, range and bearing to cursor location • Point information • Route information • Track information • AIS target information • DSC information • Tide information • Object information • Select a position for a waypoint on the plotter display. • Select an item. For example, a waypoint on the plotter display. The appearance of the cursor depends on its state - active or inactive.
1. OPERATIONAL OVERVIEW 1.7 Navigation Data Boxes The navigation data boxes, displayed at the bottom of the screen, show various navigation data fed from the sensors connected to the display unit. Two or four boxes can be displayed and you can freely change the data shown in each box. The data that you can show depends on your system configuration. The boxes can be shown or hidden with the [Nav Data] soft control.
1. OPERATIONAL OVERVIEW 1.8 Home Screen (Display Selection) 1.8.1 How to select a display The home screen has eight displays from which to choose. Press the HOME/CTRL key to show the home screen. Operate the CursorPad or rotate the RotoKeyTM to select a display. The current selection is circumscribed with a red rectangle. Press the RotoKeyTM or ENT key to confirm your selection. 1.8.2 How to switch the active screen In multi-split screens, you can switch the active screen with the HOME/CTRL key.
1. OPERATIONAL OVERVIEW 1.8.3 How to customize the home screen The home screen has seven screens that you can customize. (The full-screen plotter display cannot be customized. If you try to customize this display, the message “Can’t customize this display.” appears.) You can split the screen in up to four separate segments.
1. OPERATIONAL OVERVIEW 5. Select a display then push the RotoKeyTM. For example, select the plotter display. The chosen display appears at the location selected and the rectangle cursor moves to the adjacent screen. 6. Select a display for the right half then push the RotoKeyTM. For example, select the fish finder display. Control is returned to the home screen, where you can see the result of your selection.
1. OPERATIONAL OVERVIEW 1.8.4 Description of home screen displays Full screen displays Plotter: See page 1-7. Fish finder: See chapter 7. Tide & Celestial: Your plotter provides for calculation of the tide heights for any date. Additionally this display shows the time of sunrise, sunset, moonrise and moonset. See section 1.17. GPS status display: The GPS status display shows the location and RX signal strength of each satellite being received. See section 12.4.
1. OPERATIONAL OVERVIEW Wind meter+navigation data x2: The wind meter provides analog and digital indications of wind angle. The wind meter is fixed; however, the two boxes of navigation data can be changed. kn Meter+navigation data x2: This display provides a meter plus two navigation data boxes. The meter and boxes can be changed. The example at right shows the appearance of the SOG meter.
1. OPERATIONAL OVERVIEW Quarter screens The figure below shows the available quarter screens. Like with the half screens you can select the navigation data to display in a quarter screen. 㫂㫅 㫂㫅 Navigation data x1 Navigation data x2 㫂㫅 㫄 Navigation data x3 㫂㫅 㫄 㫂㫅 Navigation data x4 㪫 Steering Wind angle 㫂㫅 Meter x1 (ex.
1. OPERATIONAL OVERVIEW How to select the data to display in a quarter screen, half screen navigation data 1. Display a home screen that has a quarter screen or a half screen with navigation data. 2. Long press the HOME/CTRL key to select the data display to change. The selected indication is circumscribed with a red rectangle. 3. Choose [Select Data] from the RotoKey menu. 4. Rotate the RotoKeyTM to select the indication to change then push the RotoKeyTM.
1. OPERATIONAL OVERVIEW 1.9 Display Width You can change the display width to change the amount of information shown, or zoom in or out at the location you select, in the plotter and steering displays. The selected display width appears at the bottom right-hand position on the screen. The available widths depends on latitude and chart area. 20 NM To select a display width, rotate the RotoKeyTM. Clockwise to increase the width; counterclockwise to decrease the width. 1.
1. OPERATIONAL OVERVIEW Auto course-up: The course or heading is at the top of screen at the moment the auto course-up mode is selected. PT00001 5 NM 1.11 How to Move the Chart Move the chart in the following conditions. • Your boat is not in the current area. • Take a look at another area. • Enter a point at another location. To move the chart, press and hold down the CursorPad to move it to an edge of the display. The chart shifts in the direction opposite to the arrow pressed.
1. OPERATIONAL OVERVIEW 1.12 Menu Operation This section shows you how to operate the menu. There are eight menus, [General], [Map], [Plotter], [Alarms], [System], [Fish Finder], [Instruments] and [Interface]. 1. Long-push the ESC/MENU key to show the main menu. 2. Rotate the RotoKeyTM to select a menu then push the key or the ENT key to display that menu. (A menu can also be selected with the CursorPad.) For example, select the [General] menu. WIRELESS CONNECTION Plan2Nav LINK 3.
1. OPERATIONAL OVERVIEW 2) Use the up and down arrows on the CursorPad to select a numeric value. 3) Repeat steps 1) and 2) to enter remaining numeric data. 4) Press the ENT key to save the data. 5. Press the ESC/MENU key to close the menu. (Several presses may be required depending on your location in the menu.) Note: Hereafter, this manual only implies the use of the RotoKeyTM in menu operations.
1. OPERATIONAL OVERVIEW 1.14 Context-Sensitive Menus The context-sensitive menus let you quickly access the functions related to the cursorselected item. Select an applicable item then press the ENT key to show the related context-sensitive menu. Use the RotoKeyTM to select a function. The table below shows the context-sensitive menus available in each category. Item Point (inactive) Point in Route (active route) or Point (active) Context-sensitive menu [MOVE]: Move the point selected.
1. OPERATIONAL OVERVIEW Item Route (active) Route (inactive) Context-sensitive menu STOP RESTART REVERSE INSERT EXTEND INFO START ROUTE CHECK GOTO REVERSE INSERT EXTEND RENAME DELETE INFO START ROUTE CHECK Track HIDE DELETE Points List MOB mark (on Points List) [STOP]: Stop navigating the active route. [RESTART]: Restart navigating the active route. [REVERSE]: Follow the points in the active route in reverse order. [INSERT]: Add a new point to the cursor position of the active route.
1. OPERATIONAL OVERVIEW Item Screenshots (INTERNAL) Screenshots (SD CARD) Access point in wireless LAN 1-24 Context-sensitive menu Description SAVE DELETE RENAME PREVIEW [SAVE]: Copy the screenshots in the internal memory to the SD card. [DELETE]: Delete the screenshots. [RENAME]: Give the file a new name. [PREVIEW]: Show the screenshots selected on the screen. LOAD DELETE RENAME PREVIEW [LOAD]: Copy the screenshots in the SD card to the internal memory. [DELETE]: Delete the screenshots.
1. OPERATIONAL OVERVIEW 1.15 Man Overboard (MOB) The MOB mark denotes man overboard position. Enter the mark when someone falls overboard, to automatically create a route to the man overboard position. Only one mark can be displayed. 1.15.1 How to mark MOB position Long-push the EVENT/MOB key on any screen. The plotter display appears if you are using a different screen. The MOB mark is put at the latitude and longitude position of your boat at the moment the key is pressed.
1. OPERATIONAL OVERVIEW 1.17 Tide Information Your chart contains worldwide tide height and tidal current information. 1.17.1 Tide height information The tide station symbol appears at the locations of tide height recording stations. To get tide information from a tide station, put the cursor on the tide station symbol, press the ENT key then select [FULL INFO] from the context-sensitive menu to show the [OBJECTS] menu.
1. OPERATIONAL OVERVIEW 1.17.2 Tide stream information The tidal stream information is made from the tide stream data received from tide stream station. Tidal streams are marked with arrows. The size and color of the arrow indicate tide stream speed, Yellow, slow; orange, medium, and red, fast. Simple and detailed tide stream information are available. For simple information, put the cursor on a tide stream marker.
1. OPERATIONAL OVERVIEW This page is intentionally left blank.
2. TRACK Your boat’s track is plotted on the display with position information fed from the internal GPS navigator. This section shows you how to process track, from how to show or hide the track to how to change its color. 2.1 How to Show, Hide all Track Put the cursor on any part of the track then press the ENT key to show the contextsensitive menu. Select [HIDE] to hide the track. 2.2 How to Start, Stop Recording Track 1. Open the [PLOTTER] menu then select [TRACK] and [RECORD TRACK]. 2.
2. TRACK 2.4 How to Change the Color of Your Boat’s Track You can select the color for your boat’s track among red, green, light green, yellow, purple, orange, brown, and black. It is useful to change the color at regular intervals to distinguish tracks at different times of a day, for example. 1. Open the [PLOTTER] menu then select [TRACK] and [ACTIVE TRACK] to show the track color options. 2. Select a color then press the ESC/MENU key to close the menu. 2.
2. TRACK 2.7 How to Delete Track by Color When the screen becomes cluttered with track, you may want to delete some track to clear up the display. You can delete track from the context-sensitive menu or the menu. How to delete track color from the menu 1. Open the [PLOTTER] menu then select [TRACK] and [DELETE TRACK BY COLOR]. 2. Select the color to delete then press the ENT key. The message "Delete track. Are you sure?" appears. 3. Select [YES] then press the ENT key. 4.
2. TRACK 2.9 How to Find Number of Track Points Used Open the [PLOTTER] menu then select [TRACK]. See the indication at the bottom left corner of the menu. TRACK RECORD TRACK SHOW TRACK BY COLOR ACTIVE TRACK TRACK COLOR BY TEMP DELETE TRACK BY COLOR TRACK RECORDING METHOD DISTANCE TIME O䌮 Red O䌦䌦 Distance 0.01 NM 10 sec 㪫㪩㪘㪚㪢 1/30000 No. of points used/total no.
3. POINTS 3.1 What is a Point? In navigation terminology, a point is any location you mark on the plotter display. A point can be a fishing spot, reference point and other important locations. You can use a point you have entered to set a destination and create a route. This unit has 30,000 points into which you can enter position information.
3. POINTS 3.2.2 How to enter a point at the cursor position 1. Operate the CursorPad to put the cursor where desired then press the POINTS/ GOTO key. The “point” pop-up appears and shows point name, latitude and longitude position of the point, and distance and bearing to the point. No further operation is necessary to save the point under the assigned point name and the default symbol and color. To save the point under different conditions, go to step 2.
3. POINTS [Hide]: Hide the icon and its name. [Icon]: Show only the icon. 8. Use [Comment] to enter a comment about the point, with the CursorPad. The default comment is the time and date of entry of the point. A comment may have a maximum of 64 alphanumeric characters and symbols. 9. To save the point, select the [Save] button then push the RotoKeyTM key. 3.2.3 How to enter a position manually on the plotter screen Press the ENT key to show the context-sensitive menu.
3. POINTS 3.3 How to Find Detailed Point Information You can find detailed point information with the point information pop-up. Put the cursor on the point then press the ENT key. (A point is correctly selected if the “point” box appears. See the figure in section 3.2.1.) Select [DETAILED] then press the ENT key. Name Position PT0001 34º41.006N 135º41.629E Time 02-24-12 12:46PM Temp 11.3º Depth 85.7 m Fish size 21, 18, 15, 07 cm Bottom type Mud 60% Comment FURUNO 3.
3. POINTS 3.5 How to Select Visibility for Points Points can be shown or hidden individually or collectively. 1. Open the [PLOTTER] menu and select [POINTS] to show the [Points List]. 2. Select the point to edit then press the ENT key. Note: If you want to assign visibility globally, select any point. 3. Select [MODE] from the context-sensitive menu. 4. Select the visibility desired. [SHOW]: Show the selected point’s icon and point name. [ICON]: Show the icon of the selected point.
3. POINTS 3.7 How to Filter Points by Shape on the Points List You may filter points on the [Points List] by icon shape. This is useful when you are looking for points of a specific shape. 1. Open the [PLOTTER] menu and select [POINTS] to show the [Points List]. 2. Select [Filter] (at the bottom of the screen). 3. Select [ICON] to show the icon selection window. 4. Select the icon desired. 3.8 How to Delete Points You can delete individual points directly on the screen and on the [Points List].
4. ROUTES 4.1 What is a Route? Often a trip from one place to another involves several course changes, requiring a series of route points (waypoints) which you navigate to, one after another. The sequence of waypoints leading to the ultimate destination is called a route. The equipment can store 1,000 routes, with a maximum of 50 points per route. You create a route by pointing and clicking geographical positions on the screen. These positions are marked with yellow circles.
4. ROUTES 4.2.2 How to create a route from the Routes List A route can also be created from the [Routes List], with the points you have entered. 1. Open the [PLOTTER] menu and select [ROUTES] to show the [Routes List]. 2. The [New] button is selected; push the RotoKeyTM. 3. The input box (at the bottom of the screen) is showing the route name, the youngest empty route number. Change the route name if necessary. Finally, long-push the RotoKeyTM. The screen something like the one shown below appears.
4. ROUTES 5) After you have entered all the points you require, press the ESC/MENU key. The [Routes List] reappears, showing the newly entered route. 4.2.3 How to create a route with the Easy Routing feature The Easy Routing feature automatically constructs a route between two points, taking into consideration the preset values for safe depths, safe heights and boat’s width, to provide you with an estimate of a safe route to your destination.
4. ROUTES How to set the safe values for Easy Routing Follow the procedure below to set the safe values to use in Easy Routing. 1. Open the [PLOTTER] menu and select [EASY ROUTING]. 6.6 ft 39.4 ft 0.0022 NM 5.0 min 2. [SAFE DEPTH] is the minimum safe depth, namely, your boat’s draft. 3. [SAFE HEIGHT] is the minimum safe height, namely, the height of your boat. 4. [SAFE CORRIDOR] is the minimum width of the path. 5.
4. ROUTES 4. [Calculate] is selected; push the RotoKeyTM A warning about the use of easy routing appears. Read the warning then press the ENT key. Calculation begins and the right figure appears. Calculation progress is indicated with the progress bar. ER CALCULATING Calculating route Please wait 5. When the calculation is completed, the [EASY ROUTING REPORT] appears. EASY ROUTING REPORT EASY ROUTING REPORT Route has been calculated.
4. ROUTES Error messages in Easy Routing Error message Meaning Latitude of the defined points is greater than 80°. Route has not been calculated. The latitude of the points is over 80°N/S. Reselect the points. No charts with Easy Routing data found. Calculation cannot be started. You tried to use Easy Routing with no chart data. Insert appropriate chart card. Route calculation has been halted. You canceled route calculation. – Route has not been calculated.
4. ROUTES 4.4 How to Insert a Point on a Route on the Screen You can put a point between route legs when you need an additional point along a route. 1. Put the cursor on a leg of the route. 2. Press the ENT key, select [INSERT] then press the ENT key. A dashed line is overlaid on the selected leg. 3. Drag the cursor to the location where to put the point then press the ENT key. The dashed line disappears and the leg is redrawn with a solid line. 4.
4. ROUTES 4.7 Routes List 4.7.1 How to display the Routes List The [Routes List] shows all the routes saved to the internal memory. To show the [Routes List], open the [PLOTTER] menu and select [ROUTES]. Use the up and down arrows on the CursorPad to scroll the list. For multiple pages, switch between pages with the right and left arrows on the CursorPad. Function buttons The three function buttons at the bottom of the [Routes List] do the functions shown below. Use the RotoKeyTM to access the buttons.
4. ROUTES 4.7.2 Functions available in the Routes List Context-sensitive menu Select a route from the list then press the ENT key menu to show the context-sensitive menu. EDIT DELETE PLOT REVERSE REPORT GOTO [EDIT]: Edit the selected route. [DELETE]: Delete the selected route. [PLOT]: Display the selected route on the plotter display. [REVERSE]: Follow the selected route in reverse order. See the next chapter. [REPORT]: Show the route report for the selected route. [GOTO]: Navigate the route selected.
4. ROUTES [Coord Type]: Select the position display format for points globally, among ddd’mm’ss, ddd°mm.mmm, ddd°mm.mmmm, ddd.dddddd, TD. 4.8 Route Report, Route Calculator A route report provides detailed information about a route plus a route navigation calculator. The route navigation calculator lets you see the time necessary to travel to each leg and the amount of fuel required for each leg with various speeds and fuel consumption figures.
4. ROUTES 4.9 How to Display a Route on the Screen Open the [PLOTTER] menu and select [ROUTES] to show the [Routes List]. Select a route then press the ENT key. Select [PLOT] from the context-sensitive menu then press the ENT key. 4.10 How to Connect Two Routes You can connect two routes from the [Routes List]. In the example below route 1 is connected to route 2. 1. Open the [PLOTTER] menu and select [ROUTES] to show the [Routes List]. 2. Select the starting route then press the ENT key. 3.
4. ROUTES 4.12 How to Rename a Route on the Screen The default name for a route is RTXXXX (XXXX=route number). If desired, you can rename the route with one more descriptive. 1. Put the cursor on the route to rename then press the ENT key. 2. Select [Rename] then press the ENT key. An input box showing current route name appears. 3. Edit the name as appropriate then press the ENT key. 4.13 How to Delete Routes Routes can be deleted individually or collectively.
5. NAVIGATION This chapter shows you how to get to a desired destination by using “quick points,” saved points, and routes. Before you go to a point or follow a route, make sure the path to the points is clear. Zoom your chart to check for hazards which appear on a smaller scale. 5.1 How to Navigate to a Quick Point The advantage of navigating to a quick point, the cursor position, is that you do not need to save the point to the memory. However, the point is erased when a new quick point is entered.
5. NAVIGATION 5.2 How to Navigate to a Saved Point There are two methods by which to navigate to a saved point: select the point on the screen and select the point from the [Points List]. 5.2.1 How to navigate to a saved point selected on the screen Put the cursor on the saved point then press the ENT key. Select [GOTO] then press the ENT key. See the description on page 5-1 for the meaning of the symbols and lines and the sequence of events in navigation to a point.
5. NAVIGATION • A red line runs between the points on the route. The line shows the shortest path to the destination and the direction to go. Route point (yellow by default) PT00003 Arrival area (red) PT00002 XTE alarm line (red) PT00001 Navigation line • The arrival area, the radius of which is set with the arrival alarm, is shown with a red dashed circle.
5. NAVIGATION 5.4 Functions Available When You Follow a Route 5.4.1 Route check The route check feature checks the safety of a route (registered route or a go to point route). The system searches the chart along the route to find any dangerous objects, in accordance with the operator’s search conditions. If any objects are found the system alerts the user with a report. Route check does not alter the route in anyway to make it safer.
5. NAVIGATION How to do the route check 1. Put the cursor on any leg of a route then press the ENT key to show the contextsensitive menu. 2. Select [START ROUTE CHECK]. The Warning disclaimer appears; read the disclaimer then press the ENT key. The route check area is marked on the screen with a red rectangle, the width scaled to the setting of [ROUTE WIDTH] on the [ROUTE CHECK] menu. ROUTE WIDTH (set on menu) If dangerous objects are found, the [ROUTE CHECK REPORT] window shows the objects found.
5. NAVIGATION 5.4.2 Restart navigation When you follow a route, you can restart the navigation to the next point on the route from current location. When you steer to keep away from an obstruction or your boat drifts, you go off course, like shown with Line 1 in the figure. If you do not need to return to the original course, you can go to the desired point from the current position as shown in Line 2 in the figure.
6. MAP SETTINGS, 2D PERSPECTIVE/3D DISPLAYS AND SATELLITE OVERLAY This chapter shows you how to set up the map display and how to select the 2D perspective and 3D displays. 6.1 Map Setup All map settings are in the [MAP] menu. On this menu you can • Change icon size • Change the size of the place names • Select nav aids presentation format • Select chart language • Predict tide movement • Configure the information to show Open the [MAP] menu and set items according to your operating needs.
6. MAP SETTINGS, 2D PERSPECTIVE/3D DISPLAYS AND SATELLITE OVERLAY [CHART LANGUAGE]: Use [Language] to select the chart language to use to show chart information (place names, etc.), among English and major European and Asian languages. Use [Mode] to select what language to display chart information in. [Off]: Chart information is shown in English when it is not available in the chart language selected. [English]: Chart information is shown in the chart language selected when English is not available.
6.
6. MAP SETTINGS, 2D PERSPECTIVE/3D DISPLAYS AND SATELLITE OVERLAY [FIND]: The find feature helps you locate ports, tide stations, wrecks, obstructions, and points of interests (attractions, medical service, entertainment, shopping, etc.). [COORDINATES] puts the cursor on the position you enter. For example, select [PORT BY DISTANCE] to find the ports closest to your current position. PORT BY DISTANCE NM TADOTSU - TADOTSU 242 0.096 MARUGAME - MARUGAME 47 2.075 SAKAIDO KO - SAKAIDE 58 6.
6. MAP SETTINGS, 2D PERSPECTIVE/3D DISPLAYS AND SATELLITE OVERLAY 6.2 2D Perspective Display The 2D perspective display provides an aerial perspective display. Select [2D/3D] Mode and [2D Perspective] from the RotoKey menu to show this display.
6. MAP SETTINGS, 2D PERSPECTIVE/3D DISPLAYS AND SATELLITE OVERLAY 6.3 3D Display 6.3.1 3D display description The 3D display has native 3D chart design that allows full time 3D presentation. This true 3D environment gives you all of the information you require with no restrictions on the information you can see. You can plan your routes, enter points, etc. like on the 2D chart. To show the 3D display, select [2D/3D Mode] and [3D] from the RotoKey menu.
6. MAP SETTINGS, 2D PERSPECTIVE/3D DISPLAYS AND SATELLITE OVERLAY 6.3.2 How to tilt and rotate the 3D display To tilt and rotate the 3D display, first select [Mode] and [Manual] from the RotoKey menu. [Manual] appears in the orientation mode box. Long-push the ENT key to enable adjustment. The appearance of the 3D icon changes as shown in the illustration below. 3D adj. disabled ENT ENT 3D adj. enabled Tilt the chart: Operate the up and down arrow pads on the CursorPad.
6. MAP SETTINGS, 2D PERSPECTIVE/3D DISPLAYS AND SATELLITE OVERLAY 6.4 Satellite Photo Overlay You can overlay the satellite photo for your area on the 2D and 3D displays. Open the RotoKey menu then select [2D/3D Mode], [2D] or [3D] and [Vector/Satellite] to show the satellite photo. The illustration below shows the vector chart with the satellite photo overlay. How to set the level of transparency You can select the level of transparency for the parts of the satellite photo that are on water.
7. FISH FINDER OPERATIONS 7.1 How the Fish Finder Works The fish finder calculates the distance between its transducer and underwater objects like fish, lake bottom or seabed. The results are shown in different colors or shades of gray according to echo strength. The ultrasonic waves transmitted through water move at a constant speed of approximately 4800 feet (1500 meters) per second.
7. FISH FINDER OPERATIONS 7.2 Fish Finder Display The fish finder screen provides a “picture” of the echoes found by the fish finder. Echoes are scrolled across the screen from the right position to the left position. The number of minutes an echo is displayed on the screen is controlled by the picture advance speed. The echoes at the right position are the current echoes. These echoes can be from individual fish, a school of fish, or the bottom.
7. FISH FINDER OPERATIONS 7.3 How to Activate the Fish Finder Select a fish finder display at the home screen. See section 1.8. 7.4 How to Start, Stop Transmission Transmission can be controlled from the RotoKey menu. Long-push the RotoKey™ and select [Transmission] to start and stop transmission alternately. 7.
7. FISH FINDER OPERATIONS 7.5.2 How to select a zoom display The zoom displays appear on the left-half of the screen and the high or low frequency display on the right half. Three zoom displays are available: bottom lock, bottom zoom and marker zoom. How to activate a zoom display Open the full RotoKey menu, select [Zoom] then [Btm Lock], [Btm Zoom] or [Mkr Zoom]. To deactivate the zoom display, select [Off] after selecting [Zoom].
7. FISH FINDER OPERATIONS Marker zoom display The marker zoom display expands a selected area of the normal fish finder picture to full vertical size of the screen on the left-half window. You can select the part to expand with the VRM (Variable Range Marker). Move the zoom marker with the CursorPad. The area between the VRM and zoom marker is expanded. The marker can be shown or hidden and with [ZOOM MARKER] in the [FISH FINDER] menu.
7. FISH FINDER OPERATIONS 7.5.4 Bottom discrimination display The bottom discrimination display analyzes the bottom echo to categorize bottom hardness in one of four types (rocks, gravel, sand, mud) and shows the results in a colorful graphic display. A transducer or triducer that supports the bottom discrimination display is required. There are two bottom discrimination displays: graphic and probability.
7. FISH FINDER OPERATIONS • The 600 W transducers and triducers that support the bottom discrimination feature are 520-5PSD, 520-5MSD, 525-5PWD, 525STID-MSD, 525STID-PWD. • The 1 kW transducers that support the bottom discrimination feature are 50/200-1T and 50/200-12M. • The high and low frequencies are alternately transmitted, regardless of current display selection. The TX interval is slower when this feature is active.
7. FISH FINDER OPERATIONS 7.6 Automatic Fish Finder Your fish finder can be adjusted automatically, allowing you to do other tasks. 7.6.1 How the automatic fish finder works The automatic fish finder function automatically adjusts the gain, clutter, TVG and echo offset. The main features of the automatic mode are as shown below. • Gain adjusts the sensitivity of the receiver to show the bottom echo in reddishbrown, the strongest echo (default color arrangement).
7. FISH FINDER OPERATIONS 7.7 Manual Fish Finder Operation Use the manual operation to see schools of fish and the bottom echo with a fixed gain setting. The gain, range and range shift functions let you select the depth you can see on the screen. The basic range provides a "window" into the water column and range shift moves the" window" to the depth that you select. To select the manual mode, open the RotoKey menu then select [Auto Mode] and [Manual]. 7.7.
7. FISH FINDER OPERATIONS To adjust the shift, open the full RotoKey menu then select [Shift] to show the [Shift] window. Turn the key clockwise to increase the shift, counterclockwise to decrease the shift. 7.7.3 How to adjust the gain The gain controls how echoes of different strengths are displayed. Set the gain to show a slight amount of noise on the screen. Increase the gain for greater depths and lower the gain for shallow waters. CAUTION Adjust the gain correctly.
7. FISH FINDER OPERATIONS 7.8 Picture Advance Speed The picture advance speed controls how quickly the vertical scan lines move across the screen. A fast advance speed expands the size of a school of fish horizontally on the screen. A slow advance speed shortens the school of fish. Use a fast advance speed to see the hard bottom. Use a slow advance speed to see the smooth bottom. Fast Slow 1. Open the [FISH FINDER] menu and select [PICTURE ADVANCE]. 2. Select a picture advance speed.
7. FISH FINDER OPERATIONS 7.9 How to Reduce Interference Interference from other fish finders and electrical equipment appears on the screen as shown in the illustration. When these types of interference appear on the screen, use the interference rejector to reduce the interference. Three levels are available. Turn off the interference rejector when there is no interference, so that you do not erase weak echoes.
7. FISH FINDER OPERATIONS 7.11 How to Measure Depth, Time Between Locations You can measure the depth to an object with the VRM. Also, you can measure the time from the right edge to a location. For example, you can measure how many minutes ago the echo appeared. To measure the depth, press the up and down arrow pads on the CursorPad to put the VRM on the object to measure the depth. To measure time, press the right and left arrow pads on the CursorPad.
7. FISH FINDER OPERATIONS 7.13 White Marker The white marker displays the selected echo strength in white. Use this feature to distinguish fish near the bottom from the bottom echo. Open the full RotoKey menu then select [Sensitivity] and [White Marker] to show the [White Marker] window then select Off 00 [On]. Select the current the value, long-push the RotoKeyTM, rotate the key to set the echo strength number to display in white then push the key.
7. FISH FINDER OPERATIONS 7.15.1 How to set an alarm 1. Open the [ALARMS] menu and select [FISH ALARM], [FISH ALARM (B/L)], [FISH SIZE ALARM] or [BOTTOM TYPE ALARM]. An alarm setting window appears. Off Off Depth 0.0 ft Range 5 ft Min: 5 inch Max: 199 inch Fish Alarm, Fish Alarm (B/L) Probability 70 Bottom Type Alarm Fish Size Alarm 2. For the alarms other than [BOTTOM TYPE ALARM], select [On] on the first line of the alarm setting window. 3.
7. FISH FINDER OPERATIONS 7.16 ACCU-FISHTM The ACCU-FISHTM feature measures the length of individual fish and tags the fish with a fish symbol whose size is scaled to the length of the fish. The length or depth of the fish can be indicated digitally. Connection to a transducer that supports ACCU-FISHTM is required. 7.16.1 Considerations for ACCU-FISHTM • The fish length calculated by this fish finder is intended for reference purposes; it is not a completely accurate measurement of fish length.
7. FISH FINDER OPERATIONS 7.16.2 How to activate ACCU-FISHTM, select display information 1. Open the [FISH FINDER] and [ACCU-FISH] menus. 2. Select [FISH INFO] to activate or deactivate ACCU-FISHTM and select the information to display. [Off]: Deactivate ACCU-FISHTM. [Fish Size]: Show fish size. [Depth]: Show depth to the fish. Fish length or depth is shown in red. Note: You can show the fish info figure alone (without fish symbol) by turning off [FISH SYMBOLS]. 3.
7. FISH FINDER OPERATIONS 7.17 Water Temperature Graph The water temperature graph, which requires a temperature sensor, shows the surface water temperature. The water temperature indication (line) moves across the screen from right to left. The water temperature scale is available in degrees Celsius or Fahrenheit, one of which you can select with [TEMPERATURE] in the [UNITS OF MEASURE] menu in the [SYSTEM] menu. You can activate or deactivate the graph with [TEMPERATURE GRAPH] in the [FISH FINDER] menu.
7. FISH FINDER OPERATIONS 7.18 FISH FINDER Menu This section provides the descriptions for the items in the [FISH FINDER] menu that have not been mentioned previously. Scroll [BACKGROUND COLOR]: Select the background color, among black, dark blue, light blue, white and monochrome (echoes appear in tones of gray.) [COLOR BAR]: Turn the color bar on or off. [BOTTOM RANGE SHIFT AREA]: Select the position at which to show the bottom echo, when Auto Range is active.
7. FISH FINDER OPERATIONS [FULL SCREEN GAIN CONTROL]: The gain setting can be applied to only new echoes or new and existing echoes. Turn this feature on to get the gain setting applied to both new and existing echoes. The advantage of the full screen gain control is that you can quickly and easily find the right gain setting for your conditions. [FISH FINDER SETUP]: The [FISH FINDER SETUP] sub menu provides the following features.
7. FISH FINDER OPERATIONS Item Function [50 kHz BOTTOM LEVEL], [200 kHz BOTTOM LEVEL] In the default bottom level setting (0), the equipment judges consecutive strong echoes to be bottom echoes. If, in that setting, the depth indication is unstable, adjust the bottom level. If strong vertical lines extend upward from the bottom echo in the bottom lock display, lower the bottom level to weaken the vertical lines.
7. FISH FINDER OPERATIONS [RANGES]: The default range settings are suitable for most applications. However, you can customize the ranges to suit your needs, with [RANGE 1] - [RANGE 8]. Set the ranges in descending order. Be sure that each range is higher than its preceding range. 15 ft 30 ft 60 ft 120 ft 200 ft 400 ft 1000 ft 1500 ft 30 ft 30 ft 7.19 Interpreting the Display Zero line Zero line The zero line (transmission line) shows the position of the transducer.
7. FISH FINDER OPERATIONS Bottom contour The tail from a hard bottom is longer than the tail from a soft bottom, because the hard bottom reflects more of the ultrasonic pulse. An echo from shallow water gives a stronger reflection than the echo received from deep water. A longer bottom tail appears on slopes, because of the difference in travel time at both edges of the beam angle. For the rough bottom, echoes are reflected on many different planes, which displays echoes in many layers, giving a 3D effect.
7. FISH FINDER OPERATIONS Size of a school of fish Usually the size of fish echoes on the screen is proportional to the actual size of the school of fish. However, if two fish echoes appear at different depths with the same size, the school of fish at the shallower depth is displayed smaller because the ultrasonic beam widens as it propagates and a school of fish in deep water is displayed larger.
7. FISH FINDER OPERATIONS Plankton A plankton layer appears as a large amount of green or blue dots, and is a possible location for fish. A plankton layer moves down in the day and up at night. School of fish Plankton Current rip When two ocean currents of different speeds directions and water temperatures meet, a current rip occurs. A current rip appears on the screen as shown in the right illustration.
7. FISH FINDER OPERATIONS False echo When an ultrasonic pulse is transmitted, some energy leaves from each side of the beam. This energy has the name "sidelobe". Echoes from sidelobes show on the screen as false images like in the illustration shown below.
8. ALARMS The plotter section has 11 alarms that release audiovisual alarms when the specified conditions are met. These are • • • • • • • • • • • Anchor alarm Arrival alarm Black water tank alarm Depth alarm Fuel tank alarm Shear alarm Speed alarm Temperature alarm Trip alarm Water tank alarm XTE alarm When an alarm condition is met, the audio alarm sounds, a relevant alarm pop-up appears and the applicable alarm icon appears and flashes at the upper left-hand position.
8. ALARMS 8.2 Audio Alarm Conditions The audio alarm can be enabled or disabled and the alarm interval selected. 1. Open the [ALARMS] menu then select [AUDIBLE ALARM]. 2. Select [Off] or [On] as appropriate. 3. Select [INTERVAL]. 4. Select the alarm interval desired, among [Short] or [Long]. 5. Press the ESC/MENU key to close the menu. 8.3 Arrival Alarm The arrival alarm informs you that your boat is approaching a destination waypoint.
8. ALARMS 8.4 XTE Alarm The XTE (cross-track error) alarm warns you when your boat is off its intended course. You must set a destination to use this alarm. Own ship position Alarm setting Destination waypoint Intended course : Alarm area To set the XTE alarm: 1. Open the [ALARMS] menu then select [XTE ALARM]. 2. Confirm that the cursor is selecting the top line then push the RotoKeyTM. 3. Select [On]. 4. Set the alarm value at [Distance]. 5. Press the ESC/MENU key to close the menu. 8.
8. ALARMS 8.6 Shear Alarm The shear alarm, which requires water temperature data, sounds when the temperature exceeds the alarm setting for 10 seconds. To set the shear alarm: 1. Open the [ALARMS] menu then select [SHEAR ALARM]. 2. Confirm that the cursor is selecting the top line then push the RotoKeyTM. 3. Select [On]. 4. Set the alarm value at [Range]. 5. Press the ESC/MENU key to close the menu. 8.
8. ALARMS 8.8 Anchor Alarm The anchor alarm informs you that your boat is moving when it should be at rest. Alarm range Own ship position : Alarm area To set the anchor alarm: 1. Open the [ALARMS] menu then select [ANCHOR ALARM]. 2. Confirm that the cursor is selecting the top line then push the RotoKeyTM. 3. Select [On]. 4. Set the alarm value at [Distance]. 5. Press the ESC/MENU key to close the menu. 8.9 Trip Alarm The trip alarm alerts you when you have travelled the distance set.
8. ALARMS 8.11 Fuel Tank Alarm The fuel tank alarm warns you when the fuel level goes below the specified percentage. To set the fuel tank alarm: 1. Open the [ALARMS] menu then select [FUEL TANK]. 2. Confirm that the cursor is selecting the top line then push the RotoKeyTM. 3. Select [On]. 4. Set the alarm value (5 to 50%, 5% steps). 5. Press the ESC/MENU key to close the menu. 8.12 Water Tank Alarm The water tank alarm warns you when the water tank level goes below the specified percentage.
9. MEMORY CARD OPERATIONS This system uses SD and SDHC cards to store points, routes, tracks, settings, and screenshots. The system accepts cards of up to 32GB in size. 9.1 The Memory Card Screen Open the [GENERAL] menu and select [MEMORY CARD] to show the [MEMORY CARD] screen. This is where all phases of memory card operations start. Tracks Points&Routes Save 9.
9. MEMORY CARD OPERATIONS 9.3 How to Eject an SD Card To prevent loss of data on an SD card, eject the SD card from the full RotoKey menu. (If you are in the [MEMORY CARD] menu you can use the [Eject SD] button.) After ejecting the SD card, close the cover. 9.4 How to Save Data to an SD Card 1. Open the [GENERAL] menu and select [MEMORY CARD]. 2. Select the tab ([Points&Routes], [Track], [Screen], [Default]) corresponding to the item that you want to save. 3.
9. MEMORY CARD OPERATIONS 9.6 How to Delete Files from an SD Card 9.6.1 How to delete individual files from an SD card 1. Open the [GENERAL] menu and select [MEMORY CARD]. 2. Select the appropriate tab at the top of the screen then press the ENT key. 3. Select the file to delete then press the ENT key to show the context-sensitive menu. 4. Select [DELETE]. 5. You are asked "Delete the file. Are you sure?" The [YES] button is selected; press the ENT key to delete the file.
9. MEMORY CARD OPERATIONS 9.8 How to Process Screenshots The [Screenshots] tab process the screenshots saved to the memory and SD cards. You can save screenshots saved in the internal memory to the SD card and delete screenshots from both the internal memory and an SD card. 9.8.
9. MEMORY CARD OPERATIONS 9.8.3 How to delete screenshots How to delete individual screenshots 1. Open the [GENERAL] menu and select [MEMORY CARD]. 2. Select the [Screenshots] tab at the top of the screen then press the ENT key. 3. Select the SD card or internal memory as applicable. See section 9.8.1. 4. Select the screenshot to delete then push the ENT key to show the context-sensitive menu. 5. Select [DELETE]. 6. You are asked "Delete the file.
9. MEMORY CARD OPERATIONS This page is intentionally left blank.
10. OTHER FUNCTIONS 10.1 AIS Operations AIS (Automatic Identification System) is a system that continuously transmits the identification and position of your boat to AIS transponder equipped vessels within communicating range. All such vessels also receive data from other AIS transponder equipped vessels and display their positions and other relevant information. The AIS broadcasts this information over a VHF transceiver.
10. OTHER FUNCTIONS 10.1.2 How to find AIS target information Put the cursor on an AIS target symbol to show AIS target information. Name Position MMSI Call Sign SOG COG HDG CPA TCPA 10.1.3 FURUNO 34°39.0413N 135°21.8571E 456342110 1AB23 15.3 kn 234°T 235°T 3.28 NM 0:11:40 AIS activation range The default AIS activation range is 5.0 nm. Any AIS target that is within 5.0 nm of your boat is automatically activated.
10. OTHER FUNCTIONS 10.2 AIS SART Operations You can be alerted to active and test AIS SARTs in your area when the system receives the respective AIS SART sentence. When an active or test AIS SART sentence is received, a warning message box shows the type of AIS SART and the MMSI of the ship that launched the AIS SART. The system recognizes the AIS SART sentence with MMSI number from 970XXXXXX to 979XXXXXX. The example box below shows the information displayed for an active AIS SART.
10. OTHER FUNCTIONS 10.3 DSC Message Information The DSC (Digital Selective Calling) message information feature alerts you when you have received a DSC position request or a DSC distress call, via an SSB radiotelephone. The D icon marks the position of the vessel that sent the request or call on the plotter display, at the time the message was sent. The cursor is put on that position. If you are not on the plotter display, the message shown below appears.
10. OTHER FUNCTIONS 10.4 Stopwatch, Timer A stopwatch or timer is available on a navigation data display. (The stopwatch and timer cannot be used simultaneously.) The stopwatch counts elapsed time. The timer counts down the time from a specified time interval. To enable the stopwatch or timer, do the following. How to show the timer or stopwatch display 1. Display a home screen that has a quarter screen or a half screen with navigation data.
10. OTHER FUNCTIONS 10.5 How to Select Input, Output Data Select the data to receive and output. Before selecting data to output, confirm what data the external equipment requires. Output necessary data only. Outputting unnecessary data can cause receiving problems at the external equipment. 10.5.1 Input data Open the [[INTERFACE] menu and select [SELECT INPUT DEVICE]. Internal GPS Fish Finder Fish Finder Fish Finder Scroll Select the item to process then push the RotoKeyTM.
10. OTHER FUNCTIONS 10.5.2 Output data Open the [INTERFACE] menu and select [SELECT OUTPUT PGN]. Select the item to process. Select [On] or [Off] as appropriate. Scroll ) (ENVT.
10. OTHER FUNCTIONS 10.6 Engine Display Setup (INSTRUMENTS menu) Set your engine’s specifications on the [INSTRUMENTS] menu to get correct information on the engine displays. 80° to 320°F 80° to 320°F 80° to 320°F Item 10-8 Options Remarks ENGINE RPM 4000, 6000, 8000 rpm Set max. rpm. MAX OIL PRESSURE 600kPa/6Bar/80Psi 800kPa/8Bar/120Psi 1000kPa/12Bar/160Psi Set max. oil pressure ENGINE BOOST PRESSURE 160kPa/1Bar/24Psi 200kPa/2Bar/32Psi 320kPa/4Bar/40Psi Set engine boost pressure rating.
10. OTHER FUNCTIONS 10.7 Wireless LAN Setup You can connect to the internet with the built-in wireless LAN to download C-Weather information. This function is only available with the GP-1870F. About the wireless LAN • The wireless LAN function is available only in the countries which have acquired radio wave certification. Turn this function off in countries which do not have radio wave certification.
10. OTHER FUNCTIONS *1 WIRELESS CONNECTION SETUP Network Name Security *2 Signal Status *4 *3 GP-1870-EXXX-XXXX FURUNO Electric Co., Ltd. DRS4W000 34540-G-0271 FURUNO_FAR3000 Others *1 Wireless LAN signal level : -100 dB to -91 dB : -90 dB to -75 dB Ext Antenna *4 Signal level *2 Security : Encrypted (WPE, EAP, TKPI) : -46 dB to -30 dB The background color is green when the unit operates as an ad hoc connection.
10. OTHER FUNCTIONS Controls, context sensitive menu in WIRELESS CONNECTION SETUP Control Others Search Ext Antenna (Int Antenna) Wireless On (Wireless Off) Connect Forget Function Select an access point not shown in the access point list. The [CONNECTION CONFIGURATION] dialog box appears. Enter the network name and password to access. Search access points. Switch between Internal antenna and external antenna if equipped with an external antenna. Turn wireless connection on or off.
10. OTHER FUNCTIONS 10.9 C-Weather C-Weather, available with the GP-1870F, is a free weather service for Jeppesen Marine customers who use MAX compatible technology. The C-Weather service provides weather coverage throughout the world. Weather forecasts received from the leading meteorological centers are processed at Jeppesen for distribution to customers through download from the internet.
10. OTHER FUNCTIONS 3. Use the CursorPad to adjust the cursor to select the download area then press the ENT key to download the data. Note: If there is C-Weather data in the internal memory, a warning window asks if it is OK to write over the data. [Yes] is selected in the window; push the RotoKeyTM to download the data. The equipment connects to the C-Weather server, the server checks authentication, and then the downloading begins.
10. OTHER FUNCTIONS 10.9.3 How to interpret the C-Weather displays All C-Weather displays show the type of display and the date and time of the forecast in the window at top left corner. Display type Date, time of forecast Wind display The wind display provides the speed and direction of the wind, with windbarbs.
10. OTHER FUNCTIONS Wave display The wave display shows wave height with an octagon-shaped icon. The color of the icon changes according to the wave height and the arrow inside the icon moves with wave direction. Wave heights of 0.00 m to 7.50 m are shown in colors from light blue to green-yellow. Wave heights of 7.51 to 15.00 m are shown in colors from yellow-orange to red.
10. OTHER FUNCTIONS Weather type display The weather type display shows the general weather with pictoral icons, which include clouds, rain, snow, thunderstorm, fog, partly cloudy, and clear sky. The example display below shows rain to the south and southeast and fog to the northwest. You can put the cursor on a weather type icon to see the weather type in alphabet form.
10. OTHER FUNCTIONS Humidity display The humidity display provides humidity data with an octagon-shaped icon. The color of the icon changes according to the temperature and the humidity is digitally indicated inside the icon. Humidity between 0% and 50% is shown in colors from light blue to green-yellow. Humidity between 50.1% to 100% is shown in colors from yellow to red. How to find the humidity at a location Put the cursor on a humidity icon to show the humidity at that location.
10. OTHER FUNCTIONS Visibility display The visibility display provides visibility data with an octagon-shaped icon. The color of the icon changes according to the visibility and the visibility is digitally indicated inside the icon. Visibility between 0 km and 10 km is shown in colors from red to yellow. Visibility between 10.1 km and 20 km is shown in colors from yellow-green to red. How to find the visibility at a location Put the cursor on a visibility icon to show the visibility at that location.
11. CUSTOMIZING YOUR UNIT The default settings are suitable for a wide variety of applications. However, you may wish to customize settings to meet your environment, operational needs, local characteristics, etc. This chapter provides descriptions of the menu items not previously described, to help you determine the settings right for you. 11.1 GENERAL Menu WIRELESS CONNECTION Plan2Nav LINK [KEYPAD BEEP]: Activate or deactivate the key beep which sounds when a key (incl. RotoKeyTM) is operated.
11. CUSTOMIZING YOUR UNIT 11.2 PLOTTER Menu ROUTE CHECK COG LINE HEADING LINE SHIP ICON SHIP OFFSET QUICK INFO ZERO HANDLING Infinite Off Icon 1 Off On Points Zero Padding [COG LINE]: The tip of the COG line is your estimated position at the end of the time interval selected here. The COG line can be a valuable tool for evaluating the risk of collision with another vessel if AIS targets are displayed. A target whose vector passes through your ship's position is on a collision course.
11. CUSTOMIZING YOUR UNIT 11.3 SYSTEM Menu SYSTEM INFORMATION [LANGUAGE]: Select the language among English and major European and Asian languages. [UNITS OF MEASURE]: The default units of measure are based on the language selected. However, you can freely set the units of measure for distance, speed, wind speed, depth, fish size, temperature, air pressure, oil pressure, and fuel.
11. CUSTOMIZING YOUR UNIT [SPEED FILTER]: During position fixing, ship's velocity (speed) is directly measured from the GPS satellite. The raw velocity data may change randomly depending on receiving conditions and other factors. You can reduce this random variation by increasing the filter setting. Like with the latitude and longitude filter, the higher the speed filter setting the more smoothed the raw data. If the setting is too high, however, the response to speed and course change slows.
11. CUSTOMIZING YOUR UNIT This difference is called magnetic variation, and varies with respect to the observation point on earth. Your unit is preprogrammed with all the earth's magnetic variations. However, you may wish to enter variation manually, referring to a nautical chart, to refine accuracy. Set to [AUTO] to get correct variation when there is no position data. [INTERNAL GPS SETUP]: Set up the internal GPS receiver. [RESTART GPS]: Restart reception of GPS satellites.
11. CUSTOMIZING YOUR UNIT This page is intentionally left blank.
12. MAINTENANCE, TROUBLESHOOTING This section provides maintenance and troubleshooting procedures that the user can follow to get optimum performance from the equipment. Before attempting any maintenance or troubleshooting procedure please review the safety information below. If you cannot restore normal operation after following the troubleshooting procedures do not attempt to check inside the equipment; have a qualified technician check the set. IMPORTANT WARNING 12.
12. MAINTENANCE, TROUBLESHOOTING 12.2 How to Replace the Fuse The fuse (3A, Type: FGBO-A 125V 3A PBF, Code No.: 000-155-850-10) in the fuse holder on the power cable protects the display unit from high electric current and equipment fault. If you cannot turn on the power, check the fuse to see if it has blown. If the fuse has blown, find the reason before you replace the fuse. If the fuse blows again after the replacement, contact your dealer for advice. WARNING Use the proper fuse.
12. MAINTENANCE, TROUBLESHOOTING Problem The speed indication is not zero after the ship is stopped. Remedy Set [NAVIGATION SPEED] to [Low] in the [INTERNAL GPS SETUP] in the [SYSTEM] menu. Fish Finder Troubleshooting You selected a fish finder display, but no picture appears. • Check that the transducer cable is fastened. • Check if the fish finder source is correctly selected. Marks and characters appear, but no picture appears. Check that the transducer cable is connected.
12. MAINTENANCE, TROUBLESHOOTING 12.4 GPS Status Display The GPS status display shows the RX signal strength and the location of each GPS satellite received. By default, the GPS status display is provided on a home screen. GPS 3D Description of GPS status display • The graphic at the right side of the display shows the position of each GPS satellite in the sky. The circles are colored according to a satellite’s SNR.
12. MAINTENANCE, TROUBLESHOOTING 12.5 How to Restore Defaults, Clear Memory You may wish to restore default or user settings. 1. Open the [SYSTEM] menu then select [DEFAULT SETTINGS]. 2. Select one of the following according to your objective. [FACTORY DEFAULT]: Restore all default factory settings. User-saved items (waypoint, routes, etc.) are not erased. [USER DEFAULT]: Restore the user settings saved with [SAVE USER DEFAULT]. User-saved items and user settings are not erased.
12. MAINTENANCE, TROUBLESHOOTING 12.6 System Information The system information display, for use by the service technician, shows chart operating system information, license information and the data access manager report. Open the [SYSTEM] menu and select [SYSTEM INFORMATION] to show the charting operating system display. Select [License] or [DAM Report] to show the respective display. The information shown in the figure below may be different from what you see on your display.
13. INSTALLATION 13.1 Installation of Display Unit Mounting considerations The display unit can be installed on a tabletop or flush mounted in a console. Select a suitable mounting location considering the following: • Keep the display unit out of direct sunlight. • The temperature and humidity should be moderate and stable. • Locate the unit away from exhaust pipes and vents. • The mounting location should be well ventilated. • Mount the unit where shock and vibration are minimal.
13. INSTALLATION 13.2 Installation of Antenna Unit Mounting considerations The antenna unit GPA-017/017S (option) is available for receiving GPS signal with farther sensitivity. Select a suitable mounting location considering the following: • Select a location out of the radar beam. The radar beam will obstruct or prevent reception of the GPS satellite signal. • The location should be well away from a VHF antenna. A GPS receiver is interfered by a harmonic wave of a VHF antenna.
13. INSTALLATION in a position where water flow is the smoothest. Noise from the propellers also adversely affects performance and the transducer should not be mounted nearby. The lifting strakes are notorious for creating acoustic noise, and these must be avoided by keeping the transducer inboard of them. • The transducer must always remain submerged, even when the boat is rolling, pitching or up on a plane at high speed.
13. INSTALLATION disturbed flow of water around the transducer. The fairing block should be smaller than the transducer itself to provide a channel to divert turbulent water around the sides of the transducer rather than over its face. Hole for stuffing tube BOW Upper Half Lower Half Saw along slope of hull. 3. Drill a hole just large enough to pass the threaded stuffing tube of the transducer through the hull, making sure it is drilled vertically. 4.
13. INSTALLATION 13.3.2 Transom mount transducer The optional transom mount transducer is very commonly employed, usually on relatively small I/O or outboard boats. Do not use this method on an inboard motor boat because turbulence is created by the propeller ahead of the transducer. DO NOT overtighten screws, to prevent damage to the transducer. Parallel with hull Transom Less than 10° Mount at the stripe.
13. INSTALLATION 13.3.3 How to mount a transducer inside the hull The transducer may also be installed inside the hull on FRP boats. However, this installation method affects the ability to detect the bottom, fish and other objects because the ultrasound pulse is weakened when it passes through the hull. Note: This mounting method should not be used to mount the transducer that supports the ACCU-FISHTM and/or bottom discrimination display feature, since performance is greatly degraded.
13. INSTALLATION 2) Put the transducer into water-filled plastic bag. Press the transducer against the chosen site. 3) Turn the power on while pressing seconds approx. Plastic bag key two 4) Long-push the ESC/MENU key to show the main menu. 5) Rotate the RotoKey™ to select [FISH FINDER] menu. Water Hull plate 6) Rotate the RotoKey™ to select [FISH FINDER SETUP]. 7) Rotate the RotoKey™ to select [TRANSMISSION] and [LOW]. 8) Press the ESC/MENU key three times. 9) Press the HOME/CTRL key.
13. INSTALLATION 6) Rotate the RotoKey™ to select [200kHz ECHO OFFSET] and [+20]. 7) Rotate the RotoKey™ to select [50kHz BOTTOM LEVEL] and [-60]. 8) Rotate the RotoKey™ to select [200kHz BOTTOM LEVEL] and [-60]. 9) Press the ESC/MENU key three times. 13.3.4 Triducer DO NOT overtighten screws, to prevent damage to the transducer. 525STID-MSD The optional triducer 525STID-MSD is designed for thru-hull mounting. ø79 BOW 133 2.
13. INSTALLATION • Straight edge • Marine sealant • Pencil • Cable ties • Water-based anti-fouling paint (mandatory in salt water) Mounting location To ensure the best performance, the sensor must be submerged in aeration-free and turbulence-free water. Mount the sensor close to the centerline of your boat. On slower heavier displacement hulls, positioning it farther from the centerline is acceptable. Allow adequate space above the bracket for it to release and rotate the sensor upward.
13. INSTALLATION 3. Using a 4 mm, #23, or 9/64” bit, drill three holes 22 mm (7/8”) deep at the locations indicated. To prevent drilling too deeply, wrap masking tape around the bit 22 mm (7/8”) from the point. Fiberglass hull: Minimize surface cracking by chamfering the gelcoat. If a chamfer bit or countersink bit is not available, start drilling with a 6mm or 1/4” bit to a depth of 1 mm (1/16”). 4. If you know your transom angle, the bracket is designed for a standard 13° transom angle.
13. INSTALLATION 4. Repeat step 1 to ensure that the angle of the sensor is correct. Note: Do not position the sensor farther into the water than necessary to avoid increasing drag, spray, and water noise and reducing boat speed. 5. Using the vertical adjustment space on the bracket slots, slide the sensor up or down to provide a projection of 3 mm (1/8”). Tighten the screws. Cable cover Cable clamp 50 mm (2") Hull projection 3 mm (1/8") How to attach the sensor to the bracket 1.
13. INSTALLATION 1. If a hole must be drilled, choose a location well above the waterline. Check for obstructions such as trim tabs, pumps, or wiring inside the hull. Mark the location with a pencil. Drill a hole through the transom using a 19 mm or 3/4” bit (to accommodate the connector). 2. Route the cable over or through the transom. 3. On the outside of the hull secure the cable against the transom using the cable clamps.
13. INSTALLATION 13.4 Installation of Sensors (option) 13.4.1 Speed/temperature sensors ST-02MSB, ST-02PSB The speed/temperature sensors (ST-02MSB, ST-02PSB) are designed for thru-hull mounting. Install them as shown in this section. Mounting considerations Select a suitable mounting location, considering the following: • Select a location where the transducer will not be damaged in trailering, launching, hauling, and storage. • Select a mid-boat flat position.
13. INSTALLATION 13.5 Wiring All wiring are terminated at the rear of the display unit. Refer to the interconnection diagram on page S-1. Display unit (back) No use WARNING ELECTRICAL SHOCK CAN bus equipment Black DO NOT touch the pins inside the connector. Put the cap (supplied) on the connector when power is off or the transducer is disconnected. White Shield Transducer GPS antenna unit GPA-017/017S Power cable Connect the power cable to the power connector.
13. INSTALLATION GPS antenna unit (option) Connect the antenna cable to the GPS connector. How to attach the M-P-8DFB connector Dimensions in millimeters. Outer sheath Armor Inner sheath Shield 50 Remove outer sheath and armor by the dimensions shown left. Expose inner sheath and shield by the dimensions shown left. 30 Cover with heat-shrink tubing and heat. Cut off insulator and conductor by 10mm. 10 30 Twist shield end. Ship on clamp nut, gasket and clamp as shown left.
13. INSTALLATION How to extend cable length (GPA-017S) The standard cable is 10 m long. For extension, in case of the GPA-017S, an antenna cable set of 30 m or 50 m is available. Extension cable cannot be used with the GPA017. Fabricate the end of the antenna cable and attach the coaxial connector. See the preceding page. ANTENNA UNIT GPA-017S : Connector Conversion cable assy. Antenna cable 1m To display unit 1m 30 m or 50 m Fabricate locally. Transducer Connect the transducer cable to the XDR port.
13. INSTALLATION Matching box (option, required for 1kW transducer) The optional matching box (Type: MB-1100, Code No.: 000-041-353) is required toconnect the optional transducers 50B-6, 50B-6B, 200B-5S, 50/200-1T and 50/20012M. Part Type Code no. Qty Matching Box* MB-1100 000-041-353 1 Crimp-on Lug FV1.
13. INSTALLATION 13.6 Initial Settings 13.6.1 INSTALLATION SETTINGS menu The first time the system is powered, the [INSTALLATION SETTINGS] menu appears. Enter basic settings, following the procedure below. 1. If your language is English USA, the default language, go to step 4. 2. [LANGUAGE] is selected; push the RotoKeyTM to show the language selection window. 3. Rotate the RotoKeyTM to select a language then push the key.
13. INSTALLATION 4. Rotate the RotoKeyTM to select [UNITS OF MEASURE] then push the key. °F The units of measure are automatically changed according to the language selected. The available units are as shown in the table below.
13. INSTALLATION 13.6.2 CAN bus input/output How to select CAN bus input and output data 1. Long-press the ESC/MENU key to open the menu. 2. Rotate the RotoKeyTM to select [INTERFACE] then push the key. 3. Use the RotoKeyTM to select [SELECT INPUT DEVICE] then push the key. Internal GPS Fish Finder Fish Finder Fish Finder 4. Select the data to input as follows: 1) Use the RotoKeyTM to select a data then push the key.
13. INSTALLATION If the external source is a FURUNO make, its name appears below [Auto]. Select the device name to have the device feed respective data. 4) Other items are selected to [Auto]. Respective data are input if associated device is connected to the system. 5. Press the ESC/MENU key to return to the [INTERFACE] menu. 6. Use the RotoKeyTM to select [SELECT OUTPUT PGN] then push the key. (MAG. VARIATIONS) (POSN RAP. UP) (COG/SOG RAP. UP) 7. Use the RotoKeyTM to select an item then push the key.
13.
13.
13. INSTALLATION This page is intentionally left blank.
APPENDIX 1 MENU TREE ESC/MENU (long press) GENERAL KEYPAD BEEP (On, Off) PALETTE (Sunlight, Night, Normal) FONT SIZE (Large, Small) TIME OFFSET (UTC) Default settings in DAYLIGHT SAVING TIME (On, Off) bold face italic.
APPENDIX 1 MENU TREE (Con’t from previous page) 2 1 VAD Standard land VAD - [Free Value Added Data] DISPLAY (On, Off, Custom) CUSTOMIZE Road (On, Off) Land Elevation (On, Off) Standard Marine VAD - [Free Value Added Data] DISPLAY (On, Off, Custom) CUSTOMIZE Tide height station (On, Off) Port/Marina (On, Off) Tide stream station (On, Off) High Res Fishing Bathymetry - [Extra Paid Value Added Data] DISPLAY (On, Off) FIND (PORT SERVICES, PORT BY DISTANCE, PORT BY NAME, TIDE STATIONS, WRECKS, OBSTRUCTIONS
APPENDIX 1 MENU TREE 1 (Con’t from previous page) ALARMS AUDIBLE ALARM (On, Off) INTERVAL (Short, Long) ARRIVAL ALARM (Off, On, Distance: 0.01 to 5.39; 0.10 NM) XTE ALARM (Off, On, Distance: 0.00 to 5.39; 0.10NM) TEMPERATURE ALARM (Off, Within, Outside, Min: -004.00 (0.00°F) to +103.98, Max: -004.00 to +103.98 (10.00°F)) SHEAR ALARM (Off, On, Range: 00.01 to 19.99; 0.10°F) DEPTH ALARM (Off, On, Depth: 0.0 to 9999.9; 0.0 ft, Range: 0.0 to 9999.9; 10.0 ft) ANCHOR ALARM (Off, On, Distance: 0.00 to 5.39; 0.
APPENDIX 1 MENU TREE 1 2 (Con’t from previous page) AIS SETUP DISPLAY (On, Off) AIS SART TEST (On, Off) ACTIVATION RANGE (0.1 to 50.0; 5.0 NM) CPA ALARM (Off, On, 0.5 to 50.0; 0.5 NM) TCPA ALARM (Off, On, 1 to 30; 10 min) DEFAULT SETTINGS FACTORY DEFAULT USER DEFAULT SAVE USER DEFAULT CLEAR MEMORY SYSTEM INFORMATION (Show operating system information.
APPENDIX 1 MENU TREE 1 (Con’t from previous page) INTERFACE CAN BUS MONITOR (Devices, General, TX PGN List, RX PGN List, Transmitted PGNs) SELECT INPUT POSITION & SOG/COG (Internal GPS, Auto) DEVICE DEPTH (Fish Finder, Auto) WATER TEMPERATURE (Fish Finder, Auto) SPEED THROUGH WATER (Fish Finder, Auto) HEADING (Auto) AIR TEMPERATURE (Auto) HUMIDITY (Auto) WIND CHILL TEMPERATURE (Auto) DEW-POINT TEMPERATURE (Auto) AIR PRESSURE (Auto) WIND (Auto) AIS (Auto) DSC (Auto) RUDDER (Auto) RATE OF TURN (Auto) ENGINE
APPENDIX 1 MENU TREE RotoKey menu Navigation data display RotoKey™ (short push) Reset (for Timer, Stopwatch) Data Box (2 Boxes Right, 2 Boxes Left, 4 Boxes) Nav. Data (POS, WPT, DST, DST-E, BRG, XTE, TTG, ETA, DATE, TIME) Select Data Spd/Brg (SOG, COG, STW, HDG, ODD, TRIP, RUDDR, ROT) Eject SD Depth (DEPTH) Screenshot Water Temp., Air Temp. (TEMP, A-TMP, A-PRS, HUMID, DEW-P, C-TMP) Wind Dir.
APPENDIX 1 MENU TREE Sounder display Standard menu RotoKey™ (short push) Auto Mode (Fishing, Cruising, Manual) Auto Range (Auto, Manual) Gain 50 kHz (-5~+5; 0) Gain 200 kHz (-5~+5; 0) Frequency (200 kHz, 50 kHz, Dual) Data Box (2 Boxes Right, 2 Boxes Left, 4 Boxes) Full menu RotoKey™ (long push) Auto Mode (Fishing, Cruising, Manual) Auto Range (Auto, Manual) Gain 50 kHz (-5~+5; 0) Gain 200 kHz (-5~+5; 0) Frequency (200 kHz, 50 kHz, Dual) Data Box (2 Boxes Right, 2 Boxes Left, 4 Boxes) Shift (0~500 m; 0
APPENDIX 2 ABBREVIATIONS, SYMBOLS Abbreviations Abbreviation 2D 3D A-PRS A-TMP AIS AM AOR AUTO B-type Bar Bft BIOS BOOST BRG C C-TMP C-MAP CAN BUS cm COG COOL-P CPA CTRL DATE DD Demo DEPTH DEW-P DIR DOP DSC DST DST-E E E-SPD E-TMP ELV ESC ETA F AP-8 Meaning Two Dimensional Three Dimensional Air Pressure Air Temperature Automatic Identification System Ante Meridiem Atlantic Ocean Region Automatic Bottom type Barometric Beaufort Basic Input/Output System Engine Boost Pressure Bearing Celsius Wind-Chill Temp
APPENDIX 2 ABBREVIATIONS, SYMBOLS Abbreviation FF fm ft FUEL FUEL-P FUEL-R GAIN H GAIN L gal GNSS GPS HDG HDOP h HOUR hPa HR HUMID IOR JP kHz KM km/h KNT kPa LAT Lib LOAD LON m m/s M Max Min min MM MOB mph N NAD NAV NGA NM O-PRS O-TMP ODO OS pb PGN Meaning Fast File fathoms feet Fuel Rate Fuel Pressure Fuel Rate Gain High (frequency) Gain Low (frequency) gallon Global Navigation Satellite System Global Positioning System Heading Horizontal Dilution of Precision hour Total Engine Hours Hectopascal Hiro Hum
APPENDIX 2 ABBREVIATIONS, SYMBOLS Abbreviation PM POR POS PSI PT QP RES ROT RT RUDDR S SD SDHC SDK sec SIM SL SM SOG STW SYM T T-PRS T-TMP TCPA TEMP TIME TRIM TRIP TTG UK US UTC V VAD VDOP W WAAS WDA WDT WGS WPT WSA WST XTE YY AP-10 Meaning Post Meridiem Pacific Ocean Region Position Per Square Inch Point Quick Point Resolution Rate Of Turn Route Rudder South Secure Digital Secure Digital High capacity Software Development Kit second(s) Simulation Satellite statute mile Speed Over the Ground Speed Throug
APPENDIX 2 ABBREVIATIONS, SYMBOLS Symbols Plotter display symbols Item Symbol Cursor (two types) : Active : Inactive (red) MOB (ManOverBoard) mark (red) Ship icon (four types) Icon 1 Icon 2 Icon 3 Icon 4 Ship icon+COG line Ship icon+Heading line (red) Ship icon+track Point (single point and route point) (default: yellow) Wireless LAN RX strength Wireless LAN security North marker AP-11
APPENDIX 2 ABBREVIATIONS, SYMBOLS Alarm symbols ALARM ARRIVAL ALARM SYMBOL ALARM FISH ALARM (B/L) ANCHOR ALARM FISH SIZE CROSS TRACK ERROR BOTTOM TYPE SPEED ALARM FUEL TANK TRIP ALARM WATER TANK TEMPERATURE ALARM BLACK-WATER TANK SHEAR ALARM CPA ALARM DEPTH ALARM TCPA ALARM SYMBOL FISH ALARM C-Weather symbols Icon Description Description Clouds Thunderstorm Rain Clear sky (see Note) Partly cloudy (see Note) Fog Snow AP-12 Icon
APPENDIX 3 JIS CABLE GUIDE Cables listed in the manual are usually shown as Japanese Industrial Standard (JIS). Use the following guide to locate an equivalent cable locally. JIS cable names may have up to 6 alphabetical characters, followed by a dash and a numerical value (example: DPYC-2.5). For core types D and T, the numerical designation indicates the cross-sectional Area (mm2) of the core wire(s) in the cable.
APPENDIX 3 JIS CABLE GUIDE This page is intentionally left blank.
APPENDIX 4 INSTALLATION OF TEMPERATURE SENSORS The installation instructions in this chapter are copied from the manufacturer's (AIRMAR Technology Corporation) installation guide, which is included with your sensor.
APPENDIX 4 INSTALLATION OF TEMPERATURE SENSORS AP-16
APPENDIX 4 INSTALLATION OF TEMPERATURE SENSORS AP-17
APPENDIX 4 INSTALLATION OF TEMPERATURE SENSORS AP-18
APPENDIX 4 INSTALLATION OF TEMPERATURE SENSORS AP-19
FURUNO GP-1670F SPECIFICATIONS OF GPS PLOTTER/SOUNDER GP-1670F 1 1.1 1.2 1.3 1.4 1.5 GENERAL Display Display mode Projection Useable area Language 1.6 Brilliance 5.
FURUNO 5 5.1 5.2 5.
NAME UNIT 000-177-131-10 HGB10AX 000-177-130-10 K10LC3005AV 000-177-106-10 HBS47AX 000-177-129-10 MINU CLOTH FRN 100-357-161-10 20-032-1062-1 000-177-128-10 0312 003.MXP 000-021-064-00 GP-1670F DESCRIPTION/CODE № GP-1670F-E （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.） （*）は、ﾀﾞﾐｰｺｰﾄﾞに付き、注文できません。 （*） THIS CODE CANNOT BE ORDERED.
NAME UNIT 000-177-132-10 HGB11AX 000-177-130-10 K10LC3005AV 000-177-107-10 HBS48AX 000-177-129-10 MINU CLOTH FRN 100-357-161-10 20-032-1062-1 000-177-128-10 0312 003.MXP 000-021-069-00 GP-1870F DESCRIPTION/CODE № GP-1870F-E （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.） （*）は、ﾀﾞﾐｰｺｰﾄﾞに付き、注文できません。 （*） THIS CODE CANNOT BE ORDERED.
C B NJTP-3DXV 1m TNC-J-3 N-P-8DFB 0.2m 整流器 (+) 1 RECTIFIER(-) 2 PR-62 *2 3 NOTE *1: SHIPYARD SUPPLY. *2: OPTION. *3: SET THE JUMPER R1/R2 TO 'ON' POSITION. 注記 ＊１）造船所手配。 ＊２）オプション。 ＊３）ジャンパーR1,R2をONに設定する。 5 6 4 A TYPE TNC-P-3 *1 IV-2sq. PWR (+) (-) SHIELD USB USB2.
INDEX Numerics 2D perspective dispay................................6-5 3D display description................................................6-6 exaggeration ............................................6-7 tilt..............................................................6-7 A ACCU-FISHTM activating, deactivating...........................7-17 considerations ........................................7-16 fish size correction .................................7-17 AIS activation range..........................
INDEX HOME/CTRL key .................................... 1-11 Humidity display .................................... 10-17 I Input data ................................................ 10-6 Interference ............................................. 7-12 L License information ................................. 12-6 M Maintenance............................................ 12-1 Maps chart display ............................................ 6-2 chart language ........................................
INDEX Temperature alarm ....................................8-3 Temperature display ..............................10-17 Temperature graph display ......................1-15 Tide & celestial display ............................1-14 Tide height information ............................1-26 Tide stream information ...........................1-27 Timer ........................................................10-5 Track color .........................................................
FURUNO Worldwide Warranty for Pleasure Boats (Except North America) This warranty is valid for products manufactured by Furuno Electric Co. (hereafter FURUNO) and installed on a pleasure boat. Any web based purchases that are imported into other countries by anyone other than a FURUNO certified dealer may not comply with local standards.
FURUNO Warranty for North America FURUNO U.S.A., Limited Warranty provides a twenty-four (24) months LABOR and twenty-four (24) months PARTS warranty on products from the date of installation or purchase by the original owner. Products or components that are represented as being waterproof are guaranteed to be waterproof only for, and within the limits, of the warranty period stated above.
GP-1870/GP-1870F ADDENDUM TO FEATURES This addendum applies to the following Operator Manuals for the GP-1870(F) series of GPS Plotters. • OME-44760-** • OME-44770-** ** denotes version number. www.furuno.
