GPS Receiver User Manual

ManualsBrandsFuruno ManualsGPSGP-33

www.furuno.co.jp

GPS Navigator

GP-33

W3D

Summary of content (98 pages)

PAGE 1
GPS Navigator GP-33 W3D www.furuno.co.
PAGE 2
The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN Telephone : +81-(0)798-65-2111 Fax : +81-(0)798-65-4200 All rights reserved. Printed in Japan A : JAN . 2010 C1 : JAN . 31, 2011 Pub. No.
PAGE 3
IMPORTANT NOTICE General • The operator of this equipment must read and follow the descriptions in this manual. Wrong operation or maintenance can cancel the warranty or cause injury. • Do not copy any part of this manual without written permission from FURUNO. • If this manual is lost or worn, contact your dealer about replacement. • The contents of this manual and equipment specifications can change without notice.
PAGE 4
SAFETY INSTRUCTIONS WARNING Indicates a condition that can cause death or serious injury if not avoided. CAUTION Indicates a condition that can cause minor or moderate injury if not avoided. Safety Instructions for the Operator Safety Instructions for the Installer WARNING Do not disassemble or modify the equipment. Fire, electrical shock or serious injury can occur. Turn off the power immediately if water leaks into the equipment or smoke or fire is coming from the equipment.
PAGE 5
TABLE OF CONTENTS FOREWORD.................................................................................................................... v SYSTEM CONFIGURATION .......................................................................................... vi 1. OPERATIONAL OVERVIEW .................................................................................1-1 1.1 1.2 1.3 1.4 1.5 1.6 2. PLOTTER DISPLAY OVERVIEW..........................................................................2-1 2.1 2.2 2.
PAGE 6
TABLE OF CONTENTS 5.2.2 How to set a destination waypoint through the list ......................................... 5-2 5.3 How to Set Route as Destination ............................................................................... 5-2 5.4 How to Cancel Destination......................................................................................... 5-3 5.4.1 How to cancel destination with the cursor...................................................... 5-3 5.4.
PAGE 7
FOREWORD A Word to the Owner of the GP-33 Congratulations on your choice of the GP-33 GPS Navigator. For over 60 years FURUNO Electric Company has enjoyed an enviable reputation for innovative and dependable marine electronics is furthered by our extensive global network of agents and dealers. Your navigator is designed and constructed to meet the rigorous demands of the marine environment. However, no machine can perform its intended function unless installed, operated and maintained properly.
PAGE 8
SYSTEM CONFIGURATION Standalone system Antenna Unit GPA-017 Navigation PC MOB Switch External Alarm Receiver Unit GP-33 12-24VDC Standard configuration is shown with solid line.
PAGE 9
SYSTEM CONFIGURATION When no FI-5002 is connected Antenna Unit GPA-017 Navigation PC MOB Switch External Alarm Receiver Unit GP-33 Backbone cable Category of Units Units Category Antenna Unit GPA-017 Exposed to weather Receiver Unit GP-33 Protected from weather Junction Box FI-5002 (Option) vii
PAGE 10
SYSTEM CONFIGURATION This page is intentionally left blank.
PAGE 11
1. OPERATIONAL OVERVIEW 1.1 Controls W3D Key Description Selects display mode. DISP Sets destination. GO TO MENU ZOOM -Opens the Menu. (plotter and highway displays: twice, others: once) -Shows the zoom window (plotter and highway displays only). -Shifts the cursor. -Selects item on menus. (Cursorpad) BRILL WPT MOB ENT -Long press: Turns power off. -Momentary press: Turns power on./Shows Brill window. -Long press: Inscribes MOB mark.
PAGE 12
1. OPERATIONAL OVERVIEW How to detach the hard cover from the unit Put your thumbs on the front and forefingers on the catches at the sides of the cover, and pull it toward you. Catches 1.2 How to Turn Power On/Off 1. Press the /BRILL key to turn on the power. The unit beeps and then starts up with the last-used display mode. Your equipment takes about 90 seconds to find its position. The equipment shows receiver status indication at the top left-hand corner in most display modes.
PAGE 13
1. OPERATIONAL OVERVIEW 1.3 How to Adjust LCD and Key Panel Brilliance 1. Press the /BRILL key to show the following window. 2. To adjust the LCD brilliance, press /BRILL key. The setting changes “0→1→…→7→6…0→1…” continuously. Maximum setting is 7. You can use also the cursorpad (W, X) to adjust the brilliance. 3. To adjust the panel brilliance, press the cursorpad (S, T, max: 7). 4. Press ENT or MENU/ZOOM key. 1.
PAGE 14
1. OPERATIONAL OVERVIEW Plotter Display The plotter display traces own boat’s track. Waypoint mark (Shape selectable) Receiver status Cursor (displayed for approx. seven seconds) Own boat mark Course bar N 34 08.375 Horizontal display range scale Lat/Lon grids Range to cursor* Bearing to cursor* N 34 08.250 92 Boat’s track E 135 09.500 E 135 09.750 Cursor position (Own boat position when cursor is not displayed.
PAGE 15
1. OPERATIONAL OVERVIEW Highway Display The highway display provides a 3-D view of own boat’s progress toward destination. XTE (Cross-track error) scale and arrow mark Arrow shifts with boat’s XTE. When the arrow is aligned with the center line the boat is on course. The arrow blinks if boat’s XTE is greater than XTE scale range. “N (North)” is displayed, instead of the arrow, at the center of the scale when no destination is set. Direction to steer (to return to course) Bearing from : Steer right.
PAGE 16
1. OPERATIONAL OVERVIEW Steering Display The steering display provides steering information. Speed over ground Receiver status Bearing reference; MAG(netic) or TRUE Time Bearing destination Bearing scale 14.6 300 0.46 00 15 299 Time-To-Go to destination Range from own boat to destination Own boat mark Course over ground Bearing to the destination 12/11/09 17:57:40 Estimated Time of Arrival at destination Nav Data Display Receiver status Date and time 34 44.589 N 135 21.074 E 14.
PAGE 17
1. OPERATIONAL OVERVIEW Satellite Monitor Display The satellite monitor display shows the condition of GPS and GEO (WAAS) satellites. Number, bearing and elevation angle of all GPS and GEO satellites (if applicable) in view of your receiver appear. Receiver status Elevation 45 DOP value 11 1.60 GEO satellite 22 08 13 17 32 30 05 02 25 12.0 02 05 08 11 13 15 17 22 25 28 30 32 133 Receiver signal level Bars show signal level. Satellites whose signal level are high are used in fixing position.
PAGE 18
1. OPERATIONAL OVERVIEW 1.5 Menu Overview Most operations of your unit are done through the menu. Below is a quick introduction to how to select a menu and change menu settings. If you get lost in operation, press the MENU/ZOOM key to return to the main menu. 1. Press the MENU/ZOOM key once or twice to display the main menu. Press once: Steering display, nav data display, satellite monitor display, user display 1/2.
PAGE 19
1. OPERATIONAL OVERVIEW How to enter alphanumeric data Some menu operations require you to enter alphanumeric data (A to Z, 0 to 9) and symbols (&, _, #,’ , -, > and space). The procedure which follows shows how to enter alphanumeric data. For example, to change the waypoint name “WP0006” to “KOBE”, do the follows: Cursor 1) Press S or T to select “K”. 2) Press X, and press S or T to select “O”. 3) Press X, and press S or T to select “B”. 4) Press X, and press S or T to select “E”.
PAGE 20
1. OPERATIONAL OVERVIEW Shortest course from own boat to MOB position (blue) MOB mark (red) N 34 08.500 0.20 95 N 34 08.375 E 135 09.750 E 135 10.
PAGE 21
2. PLOTTER DISPLAY OVERVIEW 2.1 How to Select the Display Range You can change the display range on the plotter and highway displays. The horizontal range in the plotter display is available among 0.02, 0.05, 0.1, 0.2, 0.5, 1, 2, 5, 10, 20, 40, 80, 160 and 320 nautical miles. The horizontal range in the highway display is available among 0.2, 0.4, 0.8, 1, 2, 4, 8 and 16 nautical miles. 1. Press the MENU/ZOOM key on the plotter or highway display. The following window appears.
PAGE 22
2. PLOTTER DISPLAY OVERVIEW Cursor state and position indication Cursor position is displayed in latitude and longitude or TDs at the bottom of the plotter display when the cursor is shown. If there is no operation for about seven seconds, the cursor disappears. COG line Range from own boat to cursor Bearing from own boat to cursor 2.3 Own boat’s mark 92 Cursor Cursor position in latitude and longitude How to Shift the Display The display can be shifted on the plotter display. 1.
PAGE 23
2. PLOTTER DISPLAY OVERVIEW 2.4 How to Change Track Plotting Interval, Stop Recording To trace the boat’s track, the boat’s position is stored into the memory at an interval of distance or according to display range. For distance, a shorter interval provides better reconstruction of the track, but the storage time of the track is shorten. When the track memory becomes full, the oldest track is erased to make room for the latest.
PAGE 24
2. PLOTTER DISPLAY OVERVIEW 2.5 How to Change Track Color You can select the color for the tracks among red, yellow, green, blue, purple, black and brown. It is useful to change the color to distinguish tracks at different times of a day, for example. 1. Press the MENU/ZOOM key twice to show the main menu. 2. Select [Tracks], and press the ENT key. 3. Select [Color], and press the ENT key. 4. Select the color to use for the track, and press the ENT key. 5. Press the MENU/ZOOM key twice to close the menu.
PAGE 25
2. PLOTTER DISPLAY OVERVIEW Note: To cancel, select [No] at this step. 7. Press the MENU/ZOOM key twice to close the menu. 2.6.2 How to erase all tracks 1. Press the MENU/ZOOM key twice to show the main menu. 2. Select [Tracks], and press the ENT key. 3. Select [Delete], and press the ENT key. 4. Select [All], and press the ENT key. 5. Press W to select [Yes], and press the ENT key to erase all tracks. [Track Memory Used] on the Tracks menu shows “0%”. 6. Press the MENU/ZOOM key twice to close the menu.
PAGE 26
2. PLOTTER DISPLAY OVERVIEW This page is intentionally left blank.
PAGE 27
3. WAYPOINTS 3.1 How to Enter Waypoints In navigation terminology a waypoint is a particular location on a voyage, whether it be a starting, intermediate or destination waypoint. Your unit can store 10,000 waypoints. Waypoints can be entered on the plotter display: at cursor position, at own boat’s position, through the waypoints list and at the MOB position. Also, waypoints can be entered automatically when your boat changes course prominently. 3.1.1 How to enter a waypoint with the cursor 1.
PAGE 28
3. WAYPOINTS 4. Confirm that [New] is chosen, and press the ENT key. The default name, Lat/Lon and Comment are as follows: Name: The youngest unused waypoint number. Lat, Lon: Current own boat position Comment: Current date/time 5. To change the waypoint name, press the ENT key. Cursor 6. Operate the cursorpad to change the waypoint name (max. 8 characters). 7. To change the mark shape, select [Symbol] and press the ENT key. 8. Select a mark desired, and press the ENT key. 9.
PAGE 29
3. WAYPOINTS 12. To change the comment, select [Comment] and press the ENT key. 13. Enter the comment, and press the ENT key. 14. Press the MENU/ZOOM key to register the new waypoint into the list. 15. To register other waypoints, repeat steps 4 through 14. 16. Press the MENU/ZOOM key several times to close the menu. 3.1.4 How to enter waypoints automatically Waypoints can be entered automatically when your course changes by a specified degree.
PAGE 30
3. WAYPOINTS 3.2 How to Display Waypoint Name You can display waypoint names as follows: 1. Press the MENU/ZOOM key twice to show the main menu. 2. Select [Plotter Setup], and press the ENT key. 3. Select [WP Name], and press the ENT key. 4. Select [Disp Goto], [Disp All] or [Disp Route], and press the ENT key. Disp Goto: Displays only the destination waypoint name. Disp All: Displays all waypoint names. Disp Route: Displays all waypoint names in the route when it is set as destination. 5.
PAGE 31
3. WAYPOINTS 3.3 How to Edit Waypoints Waypoint position, name, mark shape and comment can be edited on the plotter display or through the waypoint list. Note: When the waypoint chosen is set as the destination, the message "Change The Waypoint. Are you sure?" appears. 3.3.1 How to edit waypoints on the plotter display 1. Operate the cursorpad to place the cursor on the waypoint to edit. 2. Press the ENT key to show the pop-up window. 3.
PAGE 32
3. WAYPOINTS 3.4 How to Move Waypoints You can move waypoints to any position on the plotter display. 1. Operate the cursorpad to place the cursor on the waypoint to move. 2. Press the ENT key to show the pop-up window. 3. Select [Move], and press the ENT key to show the waypoint information. 4. Operate the cursorpad to move the cursor to the new position. 5. Press the ENT key.
PAGE 33
3. WAYPOINTS 3.5 How to Erase Waypoints You can erase each or all waypoint(s). Note: You cannot erase the waypoint used as the current destination. (See paragraphs paragraph 3.5.1, paragraph 3.5.2.) 3.5.1 How to erase a waypoint on the plotter display 1. Operate the cursorpad to place the cursor on the waypoint to erase. 2. Press the ENT key to show the pop-up window. 3. Select [Delete], and press the ENT key. 3.5.2 How to erase a waypoint through the waypoint list 1.
PAGE 34
3. WAYPOINTS 3.5.3 How to erase all waypoints 1. Press the MENU/ZOOM key twice to show the main menu. 2. Select [Delete], and press the ENT key. 3. Confirm that [All Waypoints] is chosen, and press the ENT key. 4. Select [Delete], and press the ENT key. When no waypoint is set as destination When a waypoint is set as destination 5. Select [Yes], and press the ENT key to erase all waypoints. Note: To cancel, select [No]. 6. Press the MENU/ZOOM key twice to close the menu.
PAGE 35
4. ROUTES In many cases a trip from one place to another involves several course changes, requiring a series of waypoints which you navigate to, one after another. The sequence of waypoints leading to the ultimate destination is called a route. Your unit can automatically advance to the next waypoint on a route, so you do not have to change the destination waypoint repeatedly. 4.1 How to Create Routes You can store up to 100 routes, and a route can have 30 waypoints.
PAGE 36
4. ROUTES 4. Confirm that [New] is chosen, and press the ENT key to show the route information. 5. Press the ENT key to change the route name. 6. Operate the cursorpad to enter the route name, and press the ENT key (maximum: six characters). 7. Press T then ENT key. -> 8. Operate the cursorpad to enter the comment (maximum: 18 characters). 9. Press T to move the cursor to [1], and press the ENT key. Change Skip Delete 10. Confirm that [Add] is chosen, and press the ENT key. 11.
PAGE 37
4. ROUTES 4.2 How to Edit Routes You can edit the route created. Note: When the route chosen is set as route navigation, the message "Route is set as a destination. Are you sure?" appears. 4.2.1 How to replace a waypoint in a route 1. Press the MENU/ZOOM key twice to show the main menu. 2. Select [Routes], and press the ENT key. 3. Select [Alpha] or [Local], and press the ENT key to show the route list. 4. Select the route to edit, and press the ENT key. 5.
PAGE 38
4. ROUTES 4.2.3 How to insert a waypoint in a route To insert a waypoint in a route, do the following: 1. Press the MENU/ZOOM key twice to show the main menu. 2. Select [Routes], and press the ENT key. 3. Select [Alpha] or [Local], and press the ENT key to show the route list. 4. Select the route to edit, and press the ENT key. 5. Select [Edit], and press the ENT key to show the route list. 6. Select the waypoint which will come after the waypoint to be inserted, and press the ENT key. 7.
PAGE 39
4. ROUTES 8. Press the MENU/ZOOM key several times to close the menu. Note: To restore waypoint to a route, select [Skip Off] at step 7, and press the ENT key. 4.3 How to Erase a Route You can erase routes individually or collectively. 4.3.1 How to erase a route through the route list Note: The route used as route navigation can not be erased. 1. Press the MENU/ZOOM key twice to show the main menu. 2. Select [Routes], and press the ENT key. 3.
PAGE 40
4. ROUTES This page is intentionally left blank.
PAGE 41
5. DESTINATION Destination can be set four ways: by cursor, by waypoint, by route and by MOB position. Previous destination is cancelled whenever a new destination is set. The setting by MOB position is described in chapter 1. When setting a destination, a blue line is shown between own boat and the destination selected. Also, the range and bearing from own boat to the destination are shown at the left-hand side of the screen.
PAGE 42
5. DESTINATION 5.2 How to Set Destination by Waypoint You can set a waypoint as destination by using the cursor or the waypoints list. 5.2.1 How to set a destination waypoint with the cursor 1. On the plotter display, operate the cursorpad to place the cursor on the waypoint which you want to set as the destination. 2. Press the ENT key. WP0000 Goto Move Edit Delete 3. Select [Goto], and press the ENT key. 4. Cancel the destination referring to section 5.4 when arriving at the waypoint. 5.2.
PAGE 43
5. DESTINATION 3. Select [Alpha] or [Local], and press the ENT key. RT000 RT001 RT002 RT003 : WP000 : WP003 : WP001 : WP001 ->WP0001 ->WP0001 ->WP0005 ->WP0004 0.85 0.06 1.83 3.54 2 2 3 4 4. Select the route to set as a destination, and press the ENT key. 5. Select [Goto], and press the ENT key. 6. Select [Forward] or [Reverse]. Forward: Follows waypoints in order registered (1→2→3…) Reverse: Follows waypoints in reverse order registered (30 (when maximum entered) →29→28…→1) 7.
PAGE 44
5. DESTINATION 2. Press the ENT key. QP0001 Move Cancel Goto Edit Delete WP0001 Move Cancel Goto Edit Delete (for waypoint destination) (for QP destination) WP0001 Move Skip Cancel Route Edit RT0000 Cancel Route Reverse Route Info. (for route navigation) (for route leg) 3. Select [Cancel Goto (Route)], and press the ENT key. Cancel Goto. Are you sure? Yes No Cancel Route Navigation. Are you sure? Yes No (for route navigation) (for waypoint destination) 4. Chose [Yes], and press the ENT key.
PAGE 45
6. ALARMS 6.1 Overview There are nine alarm conditions which generate both audio and visual alarms: Arrival alarm, Anchor watch alarm, XTE (Cross-Track Error) alarm, Speed alarm, Speed Based Output alarm, WAAS alarm, Time alarm, Trip alarm and Odometer alarm. When an alarm setting is violated, the buzzer sounds and the name of the offending alarm and the alarm icon appear on the display (alarms other than Speed Based Output).
PAGE 46
6. ALARMS Message and meanings Message Meaning XTE ALARM! The boat is off its intended course by the range set. TIME ALARM! The time set has come. SPEED ALARM! The boat’s speed is higher than the range set. ARRIVAL ALARM! The boat is approaching the arrival area. TRIP ALARM! The boat has traveled further than the preset trip distance. ODOMETER ALARM! The boat has traveled the total distance set. ANCHOR WATCH! The boat has moved a certain distance (when it should be at rest).
PAGE 47
6. ALARMS 2. Select [Alarms], and press the ENT key. 3. Select an alarm item, and press the ENT key. 4. Do one of the following: (Arrival/Anchor) 1) Select [Arrival] or [Anchor], and press the ENT key. 2) Press X and ENT key. 3) Enter the alarm area, and press the ENT key. (XTE, Speed, Trip and Odometer) 1) Select [On], and press the ENT key. 2) Press X and ENT key. 3) Enter the value, and press the ENT key. (WAAS) Select [On], and press the ENT key. (Time) 1) Select [On], and press the ENT key.
PAGE 48
6. ALARMS 6.4 Alarm Descriptions Arrival alarm The arrival alarm informs you that own boat is approaching a destination waypoint. The area that defines an arrival zone is that of a circle which you approach from the outside of the circle. The alarm will activate if your boat enters the circle. Alarm setting Destination waypoint Own boat’s position : Alarm released How the arrival alarm works Anchor watch alarm The anchor watch alarm sounds to warn you that your boat is moving when it should be at rest.
PAGE 49
6. ALARMS XTE (Cross-Track Error) alarm The XTE alarm warns you when own boat is off its intended course. Own boat’s position Alarm setting Destination waypoint : Alarm released How the XTE alarm works Speed alarm The speed alarm alerts you when the boat’s speed is higher than the alarm range set. WAAS alarm This alarm alerts you when the WAAS signal is lost. Note that On cannot be chosen if [Mode] in Menu>WAAS is set to GPS.
PAGE 50
6. ALARMS This page is intentionally left blank.
PAGE 51
7. OTHER FUNCTIONS This chapter describes menu items not carried in other chapters. 7.1 Plotter Setup Menu COG Line You can show or hide the COG line on the plotter display. COG/BRG ref. Boat’s course and bearing to a waypoint are displayed in true or magnetic bearing. Magnetic bearing is true bearing plus (or minus) earth’s magnetic variation. Select the bearing reference in according to the compass installed: magnetic for magnetic compass, true for gyrocompass or satellite compass using true bearing.
PAGE 52
7. OTHER FUNCTIONS TTG/ETA SPD To calculate time to go and estimated time of arrival, enter your speed as below. -Auto (GPS calculated speed) 1. Press X and ENT in order. 2. Enter the speed average (1 to 999 sec.) to use, and press the ENT key. -Manual (Speed calculated manually) 1. Press X and ENT in order. 2. Enter speed (1 to 999 knot), and press the ENT key. 7.
PAGE 53
7. OTHER FUNCTIONS Smooth Position When the receiving condition is unfavorable, the GPS fix may change randomly, even if the boat is dead in water. This change can be reduced by smoothing the raw GPS fixes. The setting range is from 0 (no smoothing) to 999 seconds. The higher the setting the more smoothed the raw data, however too high a setting slows response time to change in latitude and longitude. This is especially noticeable at high boat speeds.
PAGE 54
7. OTHER FUNCTIONS 7.3 WAAS Menu * *Use “0” (as default setting). Mode You can select GPS or WAAS for the position fixing mode. WAAS Search For WAAS setting, the GEO satellite is searched automatically or manually. For GEO satellite number, see page AP-3. Auto: The system automatically searches for the optimum GEO satellite from your current position. (All satellites are searched.) Manual: Enter a GEO satellite number manually. Correction Data Set Use [0] as default setting. 7.
PAGE 55
7. OTHER FUNCTIONS Display Select the position format. • xx.xxx’: Shows L/L position with no seconds. • xx’xx.x”: Displays L/L position with seconds. • LC TD: Loran C TDs Loran C When choosing LC TD at Display, do the following: 1) Press the ENT key. 2) select the GRI code, and press the ENT key. 3) Press X and ENT key. 4) Select the pair of slave station, and press the ENT key. UTD1, UTD2 Enter TD offsets to refine Loran C position accuracy. 7.
PAGE 56
7. OTHER FUNCTIONS Time Offset GPS uses UTC time. If you would rather use local time, enter the time difference (range: -14:00 to +14:00, 15 minutes step) between it and UTC time. Daylight Saving Time For countries that use daylight savings time, select On to enable daylight savings time. Time Display You can display the time in 12 or 24 hour format. Date Display Select the date display, DD/MMM/YY or MM/DD/YY. Demo The demonstration display provides simulated operation of this unit.
PAGE 57
7. OTHER FUNCTIONS 7.6 User Display Menu To customize user displays, which are [6] and [7] appeared when the DISP key is pressed (see section 1.4), use the User Display menu. DISP key is pressed Item name on User Display menu User display 1 Display [6] Display 1 User display 2 Display [7] Display 2 B Note: You can show the User Display menu by pressing the ENT key more than three seconds at the User display 1 (display [6]) and 2 ([7]).
PAGE 58
7. OTHER FUNCTIONS Display 1, Display 2 You can select items to show on the User display 1 (display [6]) and 2 ([7]), from among digital data, speedometer and COG (see page 1-7). When choosing [Off] for Display 2, for example, the display [7] is not shown. Speedometer For [Digital], you can display one to four items of digital navigation data on the user display. 1. Press X and ENT key in order to show the following window. 2.
PAGE 59
7. OTHER FUNCTIONS 4. Select data desired, and press the ENT key. 5. Repeat steps 3 and 4 to set other data. You can select digital data also from the User display 1 (display [6]) and 2 ([7]) directly. 1. Press the DISP key several times to show User display 1 or 2 desired, and press the ENT key to show the cursor. Cursor (displayed approx. seven seconds) Volts (V) SOG (kn) 23.9 15.8 100.0 300 Trip (nm) M( ) COG 2. Operate the cursorpad to select the column to select data, and press the ENT key.
PAGE 60
7. OTHER FUNCTIONS 7.7 I/O Setup Menu Waypoint and route data can be uploaded from your unit to a PC, or downloaded from a PC to your unit. There are two kinds of data for route data: route data and route comment data. * * * * *: See chapter 9. Note: No position fix is available during uploading or downloading.
PAGE 61
7. OTHER FUNCTIONS Waypoint data format $PFEC, GPwpl, llll.ll, a, yyyyy.yy, a, c—c, c, c—c, a, hhmmss, xx, xx, xxxx 1 2 3 4 5 6 7 8 9 10 11 12 1: Waypoint latitude 2: N/S 3: Waypoint longitude 4: E/W 5: Waypoint name (1 to 8 characters) 6: Waypoint color (NULL/0: black, 1: red, 2: yellow, 3: green, 4: brown, 5: purple, 6: blue) 7: Waypoint comment (”@_ (see below.)” + 0 to 13 characters) -Internal mark code is 0x10 through 0x19.
PAGE 62
7. OTHER FUNCTIONS Route data format $GPRTE, x.x, x.x, a, c--c, c--c, ... , c--c 1 2 3 4 5 12 1: Number of sentences required for one complete route data (1 to 6) See note. 2: Number of sentences currently used (1 to 6) 3: Message mode (Always set to “C”.) 4: Route No.
PAGE 63
7. OTHER FUNCTIONS 7.7.1 Uploading data to a PC 1. Connect a PC to your GP-33, referring to the interconnection diagram at the back of this manual. 2. Press the MENU/ZOOM key twice to show the main menu. 3. Select[ I/O Setup], and press the ENT key. 4. Select [Save WPT/RTE -> PC], and press the ENT key. 5. Press W to select [Yes], and press the ENT key to start the uploading. 6. When the completion message appears, press any key to finish. 7.7.
PAGE 64
7. OTHER FUNCTIONS This page is intentionally left blank.
PAGE 65
8. MAINTENANCE, TROUBLESHOOTING NOTICE Do not apply paint, anti-corrosive sealant or contact spray to plastic parts or equipment coating. Those items contain products that can damage plastic parts and equipment coating. 8.1 Maintenance Regular maintenance is important to maintain performance. Check the following points to help maintain performance. • Check that connectors on the rear panel are firmly tightened and free of rust.
PAGE 66
8. MAINTENANCE, TROUBLESHOOTING 8.2 Troubleshooting This section provides simple troubleshooting procedures which the user can follow to restore normal operation. If you cannot restore normal operation, do not attempt to check inside the unit. Any trouble should be referred to a qualified technician. Symptom You cannot turn on the power. Remedy Check that power cable is firmly fastened. Check for damaged power cable and connector. Check battery for proper voltage output. No picture appears.
PAGE 67
8. MAINTENANCE, TROUBLESHOOTING 8.3 Displaying the Message Board When an error occurs, a message and an alarm icon appear on the screen. The message board displays the error messages (see page 6-2) shown in table below. Messages and meanings Message 8.4 Meaning, remedy GPS ERROR! Request service. GPS NO FIX! No GPS signal. Check antenna cable. RAM ERROR! Request service. ROM ERROR! Request service. BACKUP ERROR! RAM data corrupted. Try to clear backup data.
PAGE 68
8. MAINTENANCE, TROUBLESHOOTING No. Test Items Description 1 ROM, RAM test Correct: “OK”, Wrong: “NG” 2 Data3 test “-” (This test is used at factory only.) 3 GPS test Correct: “OK”, Wrong: “NG” 4 Program version No. The program version No. which is currently used appears. 5 CNT Number of test repetition. 5. Press each key one by one. The corresponded mark on the display turns red if the key is functioning properly. 6. Press the MENU/ZOOM key three times to close the test screen. 7.
PAGE 69
9. INSTALLATION 9.1 Equipment Lists Standard Supply Name Type Code No. Qty Remarks Receiver unit GP-33 - 1 Antenna Unit GPA-017 - 1 w/10 m cable Installation Materials CP20-03300 - 1 set -M12-05BM+05BF-060 -CP20-03310 Accessories FP20-01200 - 1 set See the packing list at the back of this manual. Optional Supply Name Type Qty Remarks Junction Box FI-5002 000-010-765 Cable Assy. FRU-10BFFM02M 001-112-970-10 Right Angle Antenna Base NO.
PAGE 70
9. INSTALLATION • Locate the unit away from equipment which generates electromagnetic fields such as a motor or generator. • Allow sufficient maintenance space at the sides and rear of the unit and leave sufficient slack in cables, to facilitate maintenance and servicing. • Observe compass safe distances noted on page ii to prevent interference to a magnetic compass. • Locate the unit away from direct sunlight. An LCD may black out if it is exposed to direct sunlight for a long time.
PAGE 71
9. INSTALLATION 9.2.3 Flush mount 1. Using the template (supplied), cut out a hole in the mounting location. 2. Prepare four pilot holes (for 3x20 self-tapping screws) at the mounting location. 3. Unscrew knobs to dismount the receiver unit from the hanger. This hanger can be discarded. 4. Remove the front panel from the receiver unit by unfastening the catches at the rear of the panel by hands, in the order shown in the figure below. 5 1 2 6 7 3 4 8 5.
PAGE 72
9. INSTALLATION Note: When removing the equipment from the flush mounted location, use the remover (supplied) to remove the panel as shown below. 2 Pull down 1 Insert 9.3 Installation of Antenna Unit Install the antenna unit referring to the antenna installation diagram at the back of this manual. When choosing a mounting location for the antenna unit, keep in mind the following points: • Select a location out of the radar beam. The radar beam will obstruct or prevent reception of the GPS signal.
PAGE 73
9. INSTALLATION 9.4 Wiring When no CAN bus equipment is connected When connecting no CAN bus equipment, use the red and black-colored cores of M12-05BM+05BF-060 cable to connect to the 12-24 VDC switch board. (For other cores, cut them and tape individually.) Antenna Unit GPA-017 Receiver Unit GP-33 w/10 m cable Ground FRU-10BFFM-02M cable (for NMEA 0183) Navigator, PC, External Alarm, etc.
PAGE 74
9. INSTALLATION Connection with the optional junction box FI-5002 Detailed information for the service technician about CAN bus wiring is in the document titled “Furuno CAN bus Network Design Guide (TIE-00170-*)” separately. M12-05BM+05BF-060 (6 m) Use CN2 to CN5. Power cable (2m) White Side view FI-5002 (option) Black 12VDC to switchboard (12 VDC) CN2 CN3 - CN5 BACKBONE DROP MC connector Top view Fix cable with cable tie (supplied).
PAGE 75
9. INSTALLATION Terminator • When connecting to backbone cable GP-33 MFD-BB/8/12 Backbone cable Terminator Terminator Attach the following terminators to both ends of the backbone cable. Name Type Code No.
PAGE 76
9. INSTALLATION 9.5 Language Setting When you first turn the power on after installation, you are asked the language to use on the equipment. Press S or T to select the language, and press the ENT key. 9.6 Input/Output Data This equipment inputs/outputs NMEA0183 or CAN bus data shown below. Note that NMEA 0183 version (2.0 or 3.0) can be a selected from the I/O setup screen.
PAGE 77
9.
PAGE 78
9. INSTALLATION Data 2/Data 3: NMEA Output Sentence Format** REM1 REM2 AAM* ON APB* ON BOD* ON BWC* ON ON BWR* ON ON DTM ON ON GGA ON ON GLL ON GPS ON ON GSA ON GSV ON RMB* ON ON RMC ON ON VTG ON ON XTE ZDA RTE ON ON ON ON For PC only. (See Chapter 7.) REM1/REM2: Radar, echo sounder, etc. AP: Autopilot *: Not output when no waypoint is set.
PAGE 79
9. INSTALLATION Output setting 1. Press the MENU/ZOOM key twice to show the main menu. 2. Select [I/O Setup], then press the ENT key. 3. Select [Data 2], [Data 3] or [NMEA0183 Version] depending on the equipment connected. 4. Press the ENT key. One of the following screens appears depending on the item selected at step 3. 㵰㪛㪸㫋㪸㪉㪆㪛㪸㫋㪸㪊㵱㵰㪥㪤㪜㪘㪇㪈㪏㪊㩷㪭㪼㫉㫊㫀㫆㫅㵱 5. Press S or T to select the option. REM1, 2: Output data to radar, echo sounder. AP: Output data to an autopilot.
PAGE 80
9. INSTALLATION This page is intentionally left blank.
PAGE 81
APPENDIX 1 MENU TREE MENU ZOOM Ship To Center (only when the plotter display is shown) Tracks Rec (Off, Distance, Auto; 0.00 to 9.99, 0.1 nm) Color (Red, Yellow, Green, Blue, Purple, Black, Brown) Delete (All, By Color) Track Memory Used (**%) Waypoints Alpha Local Routes Alpha Local Plotter Setup Auto Waypoint Entry (COG) (Off, On: 15 to 150 , 1 to 60 s) COG Line (Off, On) COG/BRG ref.
PAGE 82
APPENDIX 1 MENU TREE 1 AP-2 GPS Setup Datum (WGS84, WGS72, Other; 003 to 173) Navigation (Rhumb Line, Great Circle) Smooth Position (0 to 999 s, 0 s) Smooth S/C (0 to 9999 s, 5 s) Lat Offset (0.000 N/S to 9.999 N/S, 0.000’ N) Lon Offset (0.000 E/W to 9.999 E/W, 0.000’E) Disable SV SV ELV (5 to 90 , 5 ) WAAS Mode (WAAS, GPS) WAAS Search (Auto, Manual; 120 to 138) Correction Data Set (0 to 27, 99; 0) I/O Setup Data 2 (REM1, REM2, AP, GPS) Data 3 (REM1, REM2, AP, GPS) NMEA0183 Version (2.0, 3.
PAGE 83
APPENDIX 2 WHAT IS WAAS? WAAS, available in North America, is a provider in the worldwide SBAS (Satellite Based Augmentation System) navigation system. CBAS provides GPS signal corrections to SBAS users, for even better position accuracy, typically better than three meters. There are three more SBAS providers, MSAS (Multi-Functional Satellite Augmentation System) for Japan, EGNOS (Euro Geostationary Navigation Overlay Service) for Europe and GAGAN (GPS And GEO Augmented Navigation) for India.
PAGE 84
APPENDIX 3 LIST OF TERMS The following table shows the terms used in GP-33.
PAGE 85
APPENDIX 4 GEODETIC CHART LIST 001: 002: 003: 004: 005: 006: 007: 008: 009: 010: 011: 012: 013: 014: 015: 016: 017: 018: 019: 020: 021: 022: 023: 024: 025: 026: 027: 028: 029: 030: 031: 032: 033: 034: 035: 036: 037: 038: 039: 040: 041: 042: 043: 044: 045: 046: 047: 048: 049: 050: 051: 052 053: 054: 055: 056: 057: 058: 059: 060: 061: 062: 063: 064: 065: 066: 067: 068: 069: 070: 071: 072: 073: 074: 075: 076: 077: 078: 079: 080: 081: 082: 083: 084: 085: 086: 087: 088: 089: WGS84 WGS72 TOKYO NORTH AMERICAN 192
PAGE 86
APPENDIX 4 GEODETIC CHART LIST This page is intentionally left blank.
PAGE 87
FURUNO GP-33 SPECIFICATIONS OF GPS NAVIGATOR GP-33 1 GENERAL 1.1 Display system 4.3-inch color LCD 1.2 Effective area 95.04 x 53.85 mm, 480 x 272 dots (WQVGA) 1.3 Projection Mercator 1.4 Display mode Plotter, Steering, Highway, NAV data, Destination, User display 1.5 Memory capacity Track: 3,000 pts, Waypoint: 10,000 pts w/ comment (13 character) 1.6 Storage capacity 100 routes w/ 30 waypoint each 1.
PAGE 88
FURUNO 4 GP-33 POWER SUPPLY 15 VDC: LEN 7 (CAN bus) 12-24 VDC: 0.24-0.12 A (Non CAN bus) 5 ENVIRONMENTAL CONDITION 5.1 Ambient temperature Antenna unit -25°C to +70°C Receiver unit -15°C to +55°C 5.2 Relative humidity 93% at 40°C 5.3 Degree of protection IP56 5.4 Vibration IEC 60945 6 UNIT COLOR 6.1 Antenna unit N9.5 6.2 Receiver unit N2.
PAGE 89
A-1
PAGE 90
19/Oct/2010 Y.
PAGE 91
19/Oct/2010 Y.
PAGE 92
D-3 Mar.27'07 R.
PAGE 93
Y. Hatai hatai 2005.12.
PAGE 94
% $ # ࠢࡠ $.- ห਄ &+661 ห਄ &+661 ห਄ &+661 ห਄ &+661 ห਄ &+661 %0 &412A7 5*+'.& 0'6 5 0'6 % 0'6 * 0'6 . %0 &412A. 5*+'.& 0'6 5 0'6 % 0'6 * 0'6 . %0 &412A7 5*+'.& 0'6 5 0'6 % 0'6 * 0'6 . %0 &412A. 5*+'.& 0'6 5 0'6 % 0'6 * 0'6 . %0 $#%-$10'A. 5*+'.& 0'6 5 0'6 % 0'6 * 0'6 . / $((/ O Ǿ / $/ $( O Ǿ ࠕࠞ 4'& ࠢࡠ $.ࠪࡠ 9*6 ࠕࠝ $.7 %0 &412A. 5*+'.& 0'6 5 0'6 % 0'6 * 0'6 . 0'6 5 0'6 % 0'6 * 0'6 .
PAGE 95
INDEX A Alarm icon ................................................. 6-1 Alarm message ......................................... 6-1 alphanumeric data..................................... 1-9 Anchor watch alarm .................................. 6-4 Arrival alarm .............................................. 6-4 B buzzer ....................................................... 6-2 Buzzer type ............................................... 6-2 C CAN bus.....................................
PAGE 96
INDEX Time Offset ................................................7-6 Track Color ................................................2-4 Track Memory Used...................................2-3 Trip alarm ...................................................6-5 TTG/ETA SPD ...........................................7-2 U Units ...........................................................7-5 Uploading data to a PC ............................7-13 User Display...............................................
PAGE 97
PAGE 98