Installation Manual GPS RECEIVER GP-310B SAFETY INSTRUCTIONS ...........................................................................i SYSTEM CONFIGURATION ......................................................................1 EQUIPMENT LISTS ...................................................................................2 1. MOUNTING ............................................................................................3 2. WIRING ................................................................
SAFETY INSTRUCTIONS CAUTION Do not use the equipment for other than its intended purpose. Improper use of the equipment can result in personal injury or equipment damage. CAUTION Confirm that the power supply voltage is compatible with the voltage rating of the equipment. Connection to the wrong power supply can cause fire or equipment damage. No one navigation device should ever be solely relied upon for the navigation of a vessel.
This page is intentionally left blank.
SYSTEM CONFIGURATION This antenna incorporates a GPS receiver. It can be connected directly to NAVnet equipment and Multi Display RD-30. However, if it connected to an equipment other than the NAVnet product, a junction box (local supply) is required.
EQUIPMENT LISTS Standard supply No. Name 1 GPS Receiver Type GP-310B Code No. Qty Remarks 1 With 10m cable Optional equipment No. Name 1 Cable Assembly 2 Mast mounting kit 2 Type Code No.
1. MOUNTING Mounting considerations When selecting a mounting location for the antenna unit keeps in mind the following points. • The antenna may be mounted three ways: screwed into a pipe (local supply), fixed to a post with the optional mast mounting kit, or screwed into an optional mounting base. For fixing by the post or pipe, it is recommended to use stays to prevent damage to the GPS receiver. • Select a location out of the radar beam.
2. WIRING This unit outputs position and speed to external equipment, mainly to NAVnet equipment. To connect to NAVnet equipment, connect waterproof connector directly to NAVnet equipment. For connection to other equipment, use a junction box (local supply), which provides seven terminals. A ten meter cable is attached to this unit. If the distance between this unit and monitor more than 10 m, use optional extension cable (10 m). Up to four extension cables can be connected serially.
Connecting to FURUNO Multi Display RD-30 w/cable 10 m MULTI DISPLAY RD-30 AUX port AUX 12-24 VDC 12-24 VDC IN/OUT IN/OUT port Rear Panel Connecting to other type of equipment Cut the connector and fabricate the cable end, using a crimp-on lug similar terminal. Prepare a junction box locally. w/cable 10 m JUNCTION BOX YELLOW GREEN WHITE BLUE RED BLACK Drain Wire 1 2 3 4 5 6 7 non-NAVnet 3 RD-A RS-422* input for radar/plotter NMEA0183 Ver.2.00 4 RD-B 1 TD-A RS-422 output from GR-80 2 TD-B Fuse 0.
Output/Input data format Priority High ↑ ↓ Low Note1) Note2) Note3) 6 Input data Output data GPDTM GPGGA GPZDA GPGLL Setting Default of Output Cycle Yes Yes Yes Yes Yes Yes Yes Geometric datum XXGGA Position GPS fix data XXZDA UTC date UTC time and date XXGLL Position Geographic position GPGSA Fixing state, DOP Yes GPGSV Satellite Yes Yes information GPVTG Course over Yes Yes ground and ground speed XXRMC Position, UTC GPRMC Recommended Yes date minimum specific GPS/TRANSIT data Data output in order
3. DEFAULT SETTINGS Setting GPS data Initial Latitude/Longitude UTC Time Antenna Height Almanac Data Almanac Date Ephemeris Data Receiver Local Zone Time parameter PDOP Geometric Datum MASK Elevation Disable satellite Smoothing Dynamic Data Output Cycle DGPS Setting Parameter Default setting North=34’44.0000, East=135’21.
SPECIFICATIONS OF THE BLACKBOX GPS SENSOR GP-310B 1 GENERAL 1.1 Receiving Channels 12 channels parallel, 12 satellite tracking 1.2 Rx Frequency 1575.42 MHz 1.3 Rx Code C/A code 1.4 Position Fixing System All in view, 8-state Kalman filter 1.5 Position Accuracy GPS: 10 m approx., 95% of the time (HDOP DGPS: 5 m approx., 95% of the time 1.6 Tracking Velocity 999 kt 1.7 Position-fixing Time Warm start: 12 s, Cold start: 90 s 1.8 Position Update Interval 1 s 2 4) I/O INTERFACE 2.
A-1 20AU-X-9851 -1 ＰＡＣＫＩＮＧ ＬＩＳＴ GP-310B (E) N A M E ユニット 1/1 O U T L I N E DESCRIPTION/CODE № Q'TY UNIT GP-310B-E GPS受信機 1 GPS RECEIVER 000-144-512 （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.
Your Local Agent/Dealer 9-52 Ashihara-cho, Nishinomiya, Japan Telephone : 0798-65-2111 Telefax : 0798-65-4200 All rights reserved. Printed in Japan FIRST EDITION : MAR. 2001 C PUB.No. IME-44120-C ( TENI ) GP-310B : APR.
