FRS1000 RADAR/PLOTTER/SOUNDER QUICK OPERATION GUIDE (USING THE REMOTE CONTROL)
BASIC OPERATION OF FRS1000 POWERING UP YOUR FRS1000 1. Press the [POWER] key on the display 2. Allow 30 seconds for the self test to complete. ADJUSTING BRILLIANCE 1. Press the [BRILL] key on the display to activate the brilliance menu 2. Press the [BRILL] key again to increase or decrease the intensity of the display. ADJUSTING BACKGROUND COLOR 1. Press the [BRILL] key on the display to activate the brilliance menu 2.
GETTING FAMILIAR WITH THE DISPLAY FRS-1000 1 2 3 4 5 Numeric Keys 6 7 8 9 Selects a display mode 0 Open/close respective menu Adjusts display brilliance MODE BRILL RDR POWER Turns power on/off Marks man over board position and event positions PLTR MENU/ESC SNDR MOB RDR +/- Enters plus, minus and switches co-ordinate PLTR CLR SNDR ENT Silences buzzer; temporarily erases heading line, north marker; erases marks, waypoints Omnipad Shifts cursor, VRM, EBL and selects items on menus Conf
GETTING FAMILIAR WITH THE REMOTE RADAR BUTTON Used to toggle between stand-by and transmit. PLOTTER BUTTONS MOB - Press once to store an event. Later you can GOTO these events, which will be sorted from newest to oldest. Hold MOB for 5 seconds to enable MOB mode. (See page 3-8 in op. manual.) MARK - used to set a mark on the chart using either ship position or cursor position. (See page 3-6 in op. manual.) GOTO - used to go to cursor position, event, waypoint or route. (See page 3-12 in op. manual.
RADAR OPERATION COMN Decreases the Radar range scale. Increases the Radar range scale. MOB 2 3 4 5 6 7 8 9 +/- 0 CLR MARK GOTO WPT Moves the Radar cursor. ENT + ▼ ADJUSTING GAIN ▼ ESC ▼ Toggles the Radar display on and off. MODE PLTR RDR Increases or decreases the Radar’s Gain. DISP SNDR ARPA PLTR RDR SNDR ACQ RDR SNDR Increases or decreases the Radar’s Sea Clutter. Hu/Nu/Cu/TM MENU ▼ 1.
MAN OVER BOARD COMN MOB 1. Press the [MOB] key momentarily to save the current ship position as an event. These events are saved to memory and can be returned to via the GOTO L/L position method. 2 3 4 5 6 7 8 9 +/- 0 CLR GOTO WPT Confirms entry. Moves Plotter cursor in direction arrow is indicating. ENT + ▼ ESC Escapes the Plotter menu and brings you back to the display mode. Toggles the Plotter display on and off.
SOUNDER OPERATION FRS-1000 SELECTING THE SOUNDER DISPLAY 1. Press the [SNDR] MODE key to turn Sounder on 2. Press the [SNDR] MODE key again if you want to turn the Sounder display off. ST-BY TX IN PLTR COMN ZOOM OUT MOB 1 2 3 4 5 6 7 8 9 +/- 0 CLR MARK GOTO CHANGING SOUNDING RANGE WPT 1. Press the Sounder RANGE [▲] key to increase range or the Sounder RANGE [▼] key to decrease range.
Furuno USA, Inc. • 4400 NW Pacific Rim Blvd. • Camas, WA 98607-9408 Tel: (360) 834-9300 • Fax: (360) 834-9400 • www.Furuno.
