TV/AM/FM/LTE ROOFTOP ANTENNA WITH CEILING MOUNT BRACKET Instruction Manual Ceiling Mount Bracket Model: FAN73B7C-BL FAN73B7C-BL2 FAN73B7C-BL3
Welcome Thank you for purchasing this Furrion® TV/AM/FM/LTE Rooftop Antenna with ceiling mount bracket. Before operating your new product, please read these instructions carefully. This instruction manual contains information for safe use, installation and maintenance of the product. Please keep this instruction manual in a safe place for future reference. This will ensure safe use and reduce the risk of injury. Be sure to pass on this manual to new owners of this product.
2
Contents Welcome.............................................................................................1 Contents.............................................................................................3 Product Overview...............................................................................4 Product Features......................................................................................................4 Installation...................................................................
Product Overview Product Features ●● Compatible with HDTV of various digital terrestrial signals (DVB-T, ISDB-T, DTMB, ATSC), stereo and FM/AM radios.* ●● The waterproof housing is UV resistant, and is designed for superior durability using injection mold. ●● Omni directional antennas receive VHF, UHF, FM and AM signal from every point regardless of the direction you are traveling. ●● Built-in high gain and low noise amplifier.
Installation Do not install couplers, splitters, etc. between the power supply and the antenna. Installation of any item on the downlead may cause a short in the system. The downlead supplies +12VDC to the preamp in the antenna. The power supply should be turned OFF when connecting or disconnecting cables to the power supply and antenna, but should be turned ON during voltage testing. Making a New Opening 1.
Installation 4. Thread the cables of the LTE antenna base through the opening. Put the LTE antenna base over the opening area. (Fig. 3) NOTE: Make sure the center hole of the LTE antenna is aligned with the hole in the RV roof. 6. Insert the bottom collar of the TV antenna wing into the center hole of the LTE antenna base. (Fig. 5) Make sure the rubber seal on top of the LTE antenna base is in location. Collar Rubber Seal Fig. 5 Concentric Fig. 3 5.
Installation Rubber seal Collar Fig. 7 9. Follow the wiring guidelines below to connect the cables of TV/FM antenna (black) and FM/AM antenna (white) from the interior of the RV ceiling. See “Wiring Diagram” section for detail. −− TV/FM antenna (Black) with extension cable to DC powered wall-plate. −− FM/AM antenna (White) to audio system. Fig. 8 4. Fix the TV antenna wing in the base using the two 4 x 12mm square socket pan head tapping screws provided with the product. (Fig.
Installation with the cutting hole in the RV roof. Fig. 10 7. Fix the antenna base on the RV roof using seven stainless steel selftapping screws and tighten using a screwdriver. (Fig. 11)**** NOTE: Do not overtighten as damage to the base may be occur, which will void the warranty. A screw angle up to 30 degrees is acceptable without damaging the base. Fig.
Installation −− LTE Antennas: Connect to the rooftop unit by mapping the same wire color. −− Power Wires: Connect to the RV +12Vdc (current rating >1A) power source. Red is power wire, Black is ground wire. −− Network Wires: Connect to the network interface in the RV. 4. Place back the top cover to the ceiling mount bracket. (Fig. 16) Vehicle Roof Fig. 16 Power Wires LTE Antenna Network Wires Fig. 14 3.
Connections Wiring Diagram Refer to accessories page for planning connections. WARNING: The wall plate should be turned off while connecting cables. Connect the cables from the antenna to distribution wall plate and to the FM radio (AM Radio needs to connect the FM/AM antenna from the rooftop unit). Connect the power cables from the distribution wall plate according to the diagram below.
Operation Running a Channel Scan To receive maximum number of channels, a channel scan is required once the antenna and power supply have been correctly installed and all cables have been properly connected. A new scan might find any new channels that have been added in your area or find any channels that have been changed or moved since the last scan.
Specifications Technical Specification MODEL FAN73B7C-BL2 FAN73B7C-BL3 FAN73B7C-BL OPERATING CONDITION VOLTAGE 9-16Vdc, 12Vdc typical CURRENT CONSUMPTION <100mA @ 12V AM/FM ANTENNA AM FUNCTION Frequency Range 520kHz to 1710kHz Radiation Direction Omni - direction Antenna Gain FM FUNCTION 15dB Max 10dB Max Max. output level 106dBμV Frequency Range 87.
Furrion Innovation Center & Institute of Technology ● 52567 Independence Ct., Elkhart, IN 46514, USA ● Toll free: 1-800-789-3341 ● Email: support@furrion.com ©2007-2020 Furrion Ltd. Furrion® and the Furrion logo are trademarks licensed for use by Furrion Ltd. and registered in the U.S. and other countries. Patents pending (FAN73B7C-BL) FURRION.COM IM-FAV00029 V6.
OMNI-DIRECTIONAL ROOFTOP ANTENNA WITH CEILING MOUNT BRACKET FAN73B7C FAN73B7C ed ud unt Brack g Mo et ilin Inc Ce l FAN73B7C-PS x2 360˚ SIGNAL RECEPTION HD TV COMPATIBLE IP56 2 TIMES STRONGER SIGNAL STRENGTH AM & FM SIGNAL UV RESISTANT DUAL 4G ANTENNAS OPTIMIZE RECEPTION • Omni-directional antenna receives VHF, UHF, FM, AM and LTE signal from every point regardless of the direction you are traveling in • The antenna is surface-treated to withstand severe weather conditions with durable ASA mater
FAN73B7C | OMNI-DIRECTIONAL ROOFTOP ANTENNA WITH CEILING MOUNT BRACKET Omni-directional Rooftop Antenna Ceiling Mount Bracket 283⁄4” (730mm) 101⁄4” (260mm) 25⁄32” (20mm) 27⁄32” (21mm) 47⁄32” (107.3mm) 55⁄8” (143.3mm) 81⁄8” (205.4mm) 23⁄4” (70mm) 99⁄16” (242.8mm) 9⁄16” (13mm) FAN73B7C OMNI-DIRECTIONAL ROOFTOP ANTENNA WITH CEILING MOUNT BRACKET (BLACK) FAN73B7C-PS OMNI-DIRECTIONAL ROOFTOP ANTENNA WITH CEILING MOUNT BRACKET (WHITE) 515⁄16” (150.
- - - - -WARRANTY CARD Congratulations on purchasing your new Furrion product. All Furrion products are made to strict quality standards. If used properly for its intended purpose, your product should provide many years of use. We are pleased to provide you with a 1 year warranty on all Furrion products. The details of this warranty are set out in the terms and conditions (see reverse) which supplement the authorised dealer's Terms and Conditions of Sale.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ WARRANTY TERMS AND CONDITIONS_ _ _ _ _ _ _ _ _ _ _ _ __ 1. 2. 3. The warranty guarantees that Furrion products will be free from faults or defects in workmanship and materials for a period of 1 year commencing on the date of delivery to you. If a valid claim is made under warranty then you will only be entitled to claim in accordance with paragraph 6 below. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
:;=uRRION ACCESS Customized design for - - - L TE WiFi Router visit www.furrion.com/access to purchase your router.
