Assembly Instructions ASSEMBLY RATING Tools Required for Assembly: The Assembly Rating is a 5-point system showboats the degree of effort needed in Phillips Screwdriver ES assembling a specific product (with 1 being {Not Included) easy and 5 being difficult). For most Wy, products,two persons are recommended.
0-DAY LIMITED REPLACE ENT PARTS WARRANT TY This item comes with a 90-day limited replacement parts warranty to the original purchaser of new products against defects in materials and workmanship for a period of ninety (90) days from the date of receipt. This warranty is not transferable.
ASSEMBLY & CARE ADVICE FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE. BASIC ASSEMBLY TECHNIQUES It is highly recommended that the assembly should be done near the area of its intended location. Make sure you have enough space to move around during the assembly. ALWAYS have at least two people to help with transporting and assembling the product to avoid any pestilential injury and/or damage.
PER-ASSEMBLY INTRODUCTION Unless you are particularly adept at assembling furniture, we understand building ready-to-assemble furniture can be a frustrating experience for some. To help avoid confusion and to make the assembly process quicker and smoother, we have provided some helpful tips. Before you begin the assembly, please read the following : 1.
CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS (1 ) Secure the threaded end of the cam bolt by using a screwdriver. Note:Every cam lock bolt must have a cam lock connector in order to fasten the parts together. Align the cam connector with its side opening (or arrow) pointing to the small drilled hole. rd oo Tun right (clockwise) to tighten. 2) (3) Two parts should fit snugly other. 2 = Insert the cam lock against each the “7 bolt into the “ TY ed per-drilled hole above the cam Ss ) connector.
PARTS LIST (1) 1pe | 8) 1pc | (15) Ipc (2) Ipc | 1pc | (16) PCs 3) Ipc | 10) 1pe 17) PCs 4) pe | (11) 1pc (5) Ipc | (12) 1pe (6) 2pcs| (13) Ipc Ipc i Before you begin,please read"Assembly and i Care Introduction"and "Cam Lock Fastener Assembly Instructions”.
HARDWARE LIST ™ ole TEED 28X40 Ine BEX 1642 “Glue: ” apply to wood dowel first before inserting into panel Due to the size and/or weight of this product,it is highly recommended that the assembly should be done near the area of its intended location.
ASSEMBLY INSTRUCTIONS HOW TO Cam Bolt hy Cam Lock 1. Screw Cam Bolt into panel. 2. Insert Cam Bolt into bolt heel of joining panel. 3. Insert Cam Lock. arrow facing bolt. 4. Gently turn Cam Lock clockwise to lock position.
ASSEMBLY INSTRUCTIONS and does not feel loose or wobbly If it does, double check that the bolts/screws ASSEMBLY IS COMPLETE 2¢¢ 13768 secured and properly tightened Page 15 of 17
HOW TO ADJUST HINGES Gradually adjust the screws and close the door to review adjustment each time, If door is too high or too low: Loosen top and bottom screws,as shown in Fig .1, for all hinges on this door panel. Take care to support door. Adjust door up or down as necessary, hold in place.and tighten screws again. If doors have a gap in the middle or are hitting each other: Loosen screw A and B, as shown in all hinges on this door panel. Take care to support door.
Anti-Tipping strap Instruction Hardware List (Included): Tools(Not Included): Drywall Anchor 1PC = Drill & Drill Bit Metal Brackets 2PC Light H Drywall screw 1PC 9 hammer Strap 1PC poo Flathead Screw 1PC STEP 1 | 1.Use a light hammer to tap anchor into hole. . ” . 1.Find spot on wall 17 below top of item. 2. Anchor should fit snugly. If hole is too small, 2. Using a drill bit slightly thinner drill again to increase hole size .Do not force than anchor , drill hole into drywall ee fon to STEP 4 1.
