Operation Manual
9 EN
Manual Channel Presetting
You can preset a channel manually and individually.
1) Follow the steps 1) to 4) in the “Automatic Channel
Presetting”.
2) Press Cursor K / L to point to “MANUAL”, then press
ENTER
.
3) (Only for LCD-C2706 / LCD-C2707 / LCD-C2717 /
LCD-C2726 / LCD-C3206 / LCD-C3207)
Press
Cursor K / L to point to “SYSTEM”, then press
ENTER.
Press
Cursor K / L to select the desired system, then press
ENTER.
4) Press Cursor K / L to point to “POSITION”, then press
ENTER
.
5) Press the Number buttons or Cursor K / L to select your
desired position number, then press
ENTER
.
•You can select position number 01-99.
•If you want to remove scrambled signals, press
Cursor K / L repeatedly to point to “DECODER”. Then,
press
ENTER. Press Cursor K / L to select “ON”, then
press
ENTER.
6) Press Cursor K / L to point to “CHANNEL”, then press
ENTER
.
7) Press Cursor K / L to start scanning.
• The tuner will begin to search up or down automatically.
When a channel is found, the unit will stop searching and
the picture will appear on the TV screen.
•You can select desired channel number by using
the Number buttons. You must refer to the following
Channel Plan table and press three digits to select the
channel number.
(To select channel 24, press “
0” button first and then press
“
2” and “4”.)
•If this is the channel you want, press
ENTER.
This unit can receive Hyper and Oscar frequency bands.
8) Press SETUP to exit.
Note: • To confirm that a channel has been added, press
/ (prog.).
• If you insert the RF cable plug into the Aerial input
jack after manual channel presetting, a picture will be
distorted. In this case, press
/ (prog.) to select the
same channel again.
Decoder Allocation
Some TV channels transmit encoded TV signals which can only
be viewed with a purchased or hired decoder. You can connect
such a decoder to SCART1 jack of this unit. The following
function will automatically activate the connected decoder for the
desired TV channel.
1) Press STANDBY-ON to turn on the TV.
2) Press / (prog.) or the Number buttons to select the
TV channel which you would like to allocate the decoder to.
3) Press SETUP so that the menu display appears on the TV
screen.
4) Press Cursor K / L to point to “INITIAL”, then press
ENTER
.
5) Press Cursor K / L to point to “CHANNEL TUNING”,
then press
ENTER
.
6) Press Cursor K / L to point to “MANUAL”, then press
ENTER.
7) Press Cursor K / L to point to “DECODER”, then press
ENTER.
8) Press Cursor K / L to select “ON” (decoder switched on),
then press
ENTER.
•To switch off the decoder, press
Cursor K / L to select
“OFF”.
9) Press SETUP to exit.
•The decoder has now been allocated to this TV channel.
Channel Plan
TV Channel
CH
Indication
PAL I PAL B/G SECAM D/K SECAM L
01–10
IRA–
IRJ,GAP
– – F1–F10
02–12 – E2–E12 –
13–20 –
A-H
(only ITALY)
––
21–69 E21–E69
74–78 X, Y, Z, Z+1, Z+2 –
80–99, 100 S1–S20, GAP –
71–86 – – – B–Q
90–106 – – – S4–S20
121–141 S21–S41
142–153 – – R1–R12 –
SETUP
BRIGHT
AUTO
[
]
[
]
BACK
BACK SELECT OK
ENTER
PICTURE
BACK LIGHT
HDMI AUDIO
INITIAL
INITIAL
CHANNEL TUNING
LANGUAGE
BACK
BACK
BACK SELECT OK
ENTER
CHANNEL
BACK
BACK SELECT OK
ENTER
AUTO
MANUAL
MOVE
BACK
MANUAL CHANNEL
BACK
BACK SELECT OK
ENTER
POSITION
CHANNEL
DECODER
SKIP
BACK
P55
055
OFF
OFF
[
]
[
]
SETUP
BRIGHT
AUTO
[
]
[
]
BACK
BACK SELECT OK
ENTER
PICTURE
BACK LIGHT
HDMI AUDIO
INITIAL
INITIAL
CHANNEL TUNING
LANGUAGE
BACK
BACK
BACK SELECT OK
ENTER
CHANNEL
BACK
BACK SELECT OK
ENTER
AUTO
MANUAL
MOVE
BACK
MANUAL CHANNEL
BACK
BACK SELECT OK
ENTER
POSITION
CHANNEL
DECODER
SKIP
BACK
P55
055
ON
OFF
[
]
[
]
L5950EA(EN).fm Page 9 Friday, March 30, 2007 2:46 PM