Operation Manual

11
EN
To Skip a Preset Channel
The channels you can no longer receive or seldom watch can be
set to be skipped when you access channels by pressing
/ (prog.).
1) Follow the steps 1) to 3) in the “Automatic Channel
Presetting”.
2) Press Cursor K / L to point to “MANUAL”, then press
ENTER.
3) Press Cursor K / L to point to “POSITION”, then press
ENTER.
4) Press the Number buttons or Cursor K / L to select
relevant position number, then press ENTER.
5) Press Cursor K / L to point to “SKIP”, then press ENTER
to select “ON”.
• To memorise the channel again, press ENTER. Press
Cursor K / L to change “ON” into “OFF”, then press
ENTER.
6) Press SETUP to exit.
Channel Reprogramming
You can move a channel allocated to a position to another while
keeping the same total number of positions. When you move a
channel, all the other channels in the positions will be affected.
1) Follow the steps 1) to 3) in the “Automatic Channel
Presetting”.
2) Press Cursor K / L repeatedly to point to “MOVE”, then
press ENTER.
3) Press Cursor K / L repeatedly to select the position number
of the channel you want to move, then press ENTER.
• You cannot select a position number where “ ” (blank)
appears next to the number. This is because “SKIP” is set to
“ON” for this position number.
4) Press Cursor K / L repeatedly to select the new position
number, then press ENTER.
5) Press SETUP to exit.
Stereo Sound System
This TV can receive stereo and bilingual broadcasts.
Selecting the Sound Mode
You can select each mode by pressing SOUND SELECT on the
remote control. Each mode is indicated on the TV screen as
following.
• During reception of monaural broadcasts
• During reception of stereo broadcasts
• During reception of bilingual broadcasts
Note:
•
To confirm that a channel has been deleted, press
/ (prog.).
BACK
OK
ENTER
BACK
OK
ENTER
MANUAL CHANNEL
BACK
POSITION
CHANNEL
DECODER
SKIP
P55
055
[OFF ]
[ON ]
SELECTBACK
SELECTBACK
MANUAL CHANNEL
BACK
POSITION
CHANNEL
DECODER
SKIP
P55
055
[OFF ]
[OFF ]
Mode Audio output
Display on the
TV screen
Normal Monaural -None- or MONO
Mode Audio output
Display on the
TV screen
Stereo Stereo STEREO
Normal Monaural MONO
Mode Audio output
Display on the
TV screen
Main Main audio from both the speakers MAIN
Sub Sub audio from both the speakers SUB
Main / Sub
Main audio from the left speaker
Sub audio from the right speaker
MAIN + SUB
Normal
(Only for NICAM)
Monaural MONO
BACK
OK
ENTER
2
3
4
5
6
7
8
9
1

002
003
004
005
006
007
008
009
010
011
12
13
14
15
16
17
18
19
11

012
013
014
015
016
017
018
019
0
0
BACK
OK
ENTER
2
3
4
5
6
7
8
9
1

002
003
004
005
006
007
008
009
010
011
12
13
14
15
16
17
18
19
11

012
013
014
015
016
017
018
019
0
0
BACK
OK
ENTER
2
3
4
5
6
7
8
9
1

002
003
004
005
006
007
008
009
010
011
012
12
13
14
15
16
17
18
19
11

013
014
015
016
017
018
019
0
0
BACK
OK
ENTER
CHANNEL
BACK
AUTO
MANUAL
MOVE
MOVE CHANNEL
MOVE CHANNELMOVE CHANNEL
SELECTBACK
SELECTBACK
SELECTBACK SELECTBACK
POSITION
NUMBER
CHANNEL
NUMBER
A73F0EP_EN.book Page 11 Wednesday, September 12, 2007 10:48 AM