LED Puck ONE LED effect user manual
Musikhaus Thomann Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet: www.thomann.de 21.11.
Table of contents Table of contents 1 Safety instructions..................................................................................................................................... 4 2 Features....................................................................................................................................................... 10 3 Installation and starting up................................................................................................................ 3.
Safety instructions 1 Safety instructions This user manual contains important information on the safe operation of the device. Read and follow all safety notes and all instructions. Save this manual for future reference. Make sure that it is available to all persons using this device. If you sell the device to another user, be sure that they also receive this manual. Our products and user manuals are subject to a process of continuous development.
Safety instructions Safety DANGER! Danger for children Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children. Choking hazard! Ensure that children do not detach any small parts (e.g. knobs or the like) from the unit. They could swallow the pieces and choke! Never let children unattended use electrical devices. DANGER! Electric shock caused by high voltages inside Within the device there are areas where high voltages may be present.
Safety instructions WARNING! Eye damage caused by high light intensity Never look directly into the light source. NOTICE! Risk of fire Do not block areas of ventilation. Do not install the device near any direct heat source. Keep the device away from naked flames.
Safety instructions NOTICE! Operating conditions This device has been designed for indoor use only. To prevent damage, never expose the device to any liquid or moisture. Avoid direct sunlight, heavy dirt, and strong vibrations. Only operate the device within the ambient conditions specified in the chapter ‘Technical specifications’ of this user manual.
Safety instructions NOTICE! External power supply The device is powered by an external power supply. Before connecting the external power supply, ensure that the input voltage (AC outlet) matches the voltage rating of the device and that the AC outlet is protected by a residual cur‐ rent circuit breaker. Failure to do so could result in damage to the device and pos‐ sibly the user.
Safety instructions NOTICE! Risk of fire The optical lenses of the device focus the light and can cause a burning glass effect when exposed to sunlight. Never expose unassembled lenses to direct sun‐ light. Use the device only in areas where 2.4 GHz radio transmission is permitted.
Features 2 Features The LED Puck ONE lighting system produces impressive lighting effects and is ideal for mobile use.
Features Item no. Name 457259 Fun Generation LED Puck ONE Power Supply 457258 Fun Generation LED Puck ONE Remote 2,4 GHz 457180 Fun Generation LED Puck ONE Set of 1 457181 Fun Generation LED Puck ONE Set of 2 457182 Fun Generation LED Puck ONE Set of 4 457183 Fun Generation LED Puck ONE Single Unit 460372 Fun Generation LED Puck ONE USB Cable 2.
Installation and starting up 3 Installation and starting up 3.1 Connecting the device Mounting options You can mount the device in three different ways: n Standing on a smooth surface n Fixing by magnet n M6 inner screw thread (thread depth 6 mm) Connecting the LED light The device is powered by the USB power adapter or a power bank. Connect a maximum of 2 devices per USB port (max 4 devices per splitter).
Installation and starting up 1. The remote control is in sleep mode by default. Press any button on the remote control to activate it. ð The remote control is activated for 5 minutes. It can now receive and transmit radio signals. 2. Connect the LED light to a USB power source. ð The group set on the remote control flashes. 3. To change the assignment of the group, press [GROUP] on the remote control. After 5 seconds, the group assignment mode will automatically turn off.
Installation and starting up 3.
Installation and starting up Button Function 1 1, 2, 3, 4 Display for groups 1…4. The button of the selected group lights up red. 2 [GROUP] You can control up to four groups of devices separately. Press [GROUP] to select the group to control. The button of the selected group lights up red. Hold down [GROUP] to control all groups simultaneously. 3 4 Press to enable the sound control. Press again to disable the sound control. Press to select a preprogrammed static colour or effect.
Installation and starting up Button 5 Function Press to select a preprogrammed static colour or effect. Hold down to access preset 20. Preset 1…14: static colours Preset 15…20: preprogrammed colour changes or sequences 6 [SLOW] Press [SLOW] to decrease the flash frequency of the respective static colour (preset 1…14) or the speed of the respective pro‐ gramme (Preset 15…20). Hold down [SLOW] to pause the flash effect of a static colour or of a programme sequence.
Installation and starting up Button 9 10 [BLACKOUT] Function Press to increase the brightness in increments of 20 %. Press [BLACKOUT] to blackout the light. The lights are still in ON state during the blackout. 3.3 Changing the lens The device is delivered with two optical lenses (Effect Lens, 50° beam angle, and Frost Filter, 160° beam angle). You can change the lens of the device for a different effect.
Installation and starting up 1. Turn the aluminium ring on the top of the device counterclockwise. 2. Remove the existing lens and insert another lens. When using the Effect Lens, make sure that the smooth side of the lens faces the device and that the rippled side is on the outside. 3. Turn the aluminium ring on the top of the device clockwise to close the device again. 3.
Installation and starting up Number Programme Number Programme 4 Yellow 14 Pastel blue 5 Light green 15 Blue, red 6 Cyan 16 Magenta, white 7 Cyan blue 17 White, blue 8 Blue 18 Pastel red, pastel green, pastel blue 9 Blue-magenta 19 Yellow, magenta, blue 10 Magenta 20 Rainbow colours LED Puck ONE 19
Technical specifications 4 Technical specifications Light source 1 × RGBW LED, 12 W Light source properties Colour temperature White: 8000 K Optical properties Beam angle Effect Lens: 50° Frost Filter: 160° Control Input connections Remote control Voltage supply USB port for connecting a mains adapter or power bank Voltage supply Plug-in power supply (5 V Protection class IP60 Mounting options Upright / 400 mA , centre positive) Magnet M6 inner screw thread (thread depth 6 mm) Dimension
Technical specifications Weight Ambient conditions 96 g Temperature range 0 °C…40 °C Relative humidity 50 %, non-condensing LED Puck ONE 21
Troubleshooting 5 Troubleshooting In the following we list a few common problems that may occur during operation.
Troubleshooting Symptom Remedy The device can not be controlled with the remote control. Light and remote control are not paired. Pair the device with the remote con‐ trol. The light is in the wrong group. Select the correct group. The light does not turn on. The light is not connected to the power supply. Connect the light to the USB power supply or to a power bank. Battery of the power bank is empty. Charge the power bank. Blackout is activated. Press [BLACKOUT] again or The light flickers.
Troubleshooting If the procedures recommended above do not succeed, please contact our Service Center. You can find the contact information at www.thomann.de.
Protecting the environment 6 Protecting the environment Disposal of the packaging mate‐ rial For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
Notes LED effect 26
Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.
