Use & Care Manual

ENGLISH
30
Use & Care Manual
Before calling for service, check the following to avoid unnecessary service charges.
Oven Problem Problem Solving Steps
E008 Error appears
in the display window.
A problem with latch mechanism occurred. Remove power and turn it back on again after
a few seconds. The oven should run a latch auto–test. If condition persists, note the code
number and call an authorized service center.
Other E Error appears in
the display window.
Remove power and turn it back on again after a few seconds. If condition persists, note
the code number and call an authorized service center.
The oven display stays
OFF
Turn off power at the main power supply (fuse or breaker box). Turn breaker back on. If
condition persists, call an authorized service center.
Cooling fan continues to
run after oven is turned off
7KHIDQWXUQVRIIDXWRPDWLFDOO\ZKHQWKHHOHFWURQLFFRPSRQHQWVKDYHFRROHGVXI¿FLHQWO\
Oven door is locked and
will not release, even after
cooling
Turn the oven off at the circuit breaker and wait a few seconds. Turn breaker back on.
The oven should reset itself and will be operable.
Oven is not heating &KHFNWKHFLUFXLWEUHDNHURUIXVHER[WR\RXUKRXVH0DNHVXUHWKHUHLVSURSHUHOHFWULFDO
SRZHUWRWKHRYHQ0DNHVXUHWKHRYHQWHPSHUDWXUHKDVEHHQVHOHFWHG
Oven is not cooking evenly Refer to cook charts for recommended rack position. Always reduce recipe temperature
by 25 °F (15 °C) when baking with Convention Bake mode.
Oven temperature is too
hot or too cold
The oven thermostat needs adjustment. See Calibrating Oven Temperature, Page 15.
Oven light is not working
properly
Replace or reinsert the light bulb if loose or defective. See Page 28. Touching the bulb
ZLWK¿QJHUVPD\FDXVHWKHEXOEWREXUQRXW
Oven light stays on Check for obstruction in oven door. Check to see if hinge is bent or door switch broken.
Cannot remove lens cover
on light
There may be a soil build-up around the lens cover. Wipe lens cover area with a clean dry
towel prior to attempting to remove the lens cover.
Oven will not Self-Cleaning
properly
Allow the oven to cool before running Self-Cleaning. Always wipe out loose soils or heavy
spill-over before running Self-Cleaning. If oven is badly soiled, set oven for a four-hour
Self-Cleaning. See Preparing the Oven for Self-Cleaning, Page 23 to 24.
Clock and timer are not
working properly
0DNHVXUHWKHUHLVSURSHUHOHFWULFDOSRZHUWRWKHRYHQ6HHWKH&ORFNDQG7LPHUVHFWLRQV
on Page 10.
Excessive moisture :KHQXVLQJ%DNHPRGHSUHKHDWWKHRYHQ¿UVW&RQYHFWLRQ%DNHDQG&RQYHFWLRQ5RDVW
will eliminate any moisture in oven (this is one of the advantages of convection).
Porcelain chips When oven racks are removed and replaced, always tilt racks upward and do not force
them to avoid chipping the porcelain.
Service Data Record
For authorized service or parts information see paragraph “Warranty ..”
The location of the serial tag on the product can be seen when the oven door is opened. It is located on the left side,
FHQWHUHGYHUWLFDOO\MXVWLQVLGHWKHRYHQFDYLW\6HH3DJH1RZLVDJRRGWLPHWRZULWHWKLVLQIRUPDWLRQLQWKHVSDFH
below provided. Keep your invoice for warranty validation.
0RGHO1XPEHUBBBBBBBBBBBB6HULDO1XPEHUBBBBBBBBBBBBBBBB'DWHRI,QVWDOODWLRQRU2FFXSDQF\BBBBBBBBBBBBBBB
Solving Operational Problems