Quick Guide

Quick Guide Quick Guide Quick Guide Quick Guide Quick Guide Quick Guide Quick Guide Quick Guide Quick Guide
Overview
Thank you for choosing our Wireless Microphones.
This device adopts 2.4G AFH (adapve frequency hopping) and innovave
SMULL (Synchronized Mul-node Ultra Low-Latency) technology, provides
high quality audio, stable and reliable signal transmission. It can be widely
used in interviews, short video recordings, program hosng, live streaming,
teaching and training, and other wireless applicaons.
Thisproductlineincludesthefollowingmodels:
S1000:
Transmier×1
×1Receiver
×1Storage box
×1Storage bag
×1Lavalier microphone
×1Type-C OTG audio cable
×1Camera audio cable
×1Type-C recharging cable
×1Furry windscreen
S1000PRO:
Ⅰ.Userinterfaceoftransmier(TX)
—1—
Power/Mute buon: press and hold for 1 second to turn on or off; short
press to mute or unmute the microphone
Charging socket
Reset hole: use a needle tool to click the buon in the hole to restore the
factory default sengs
Connecon status indicator: lights on while connecng with the receiver,
lights off means no connecon
Baery indicator: lights when it is on, flashes when baery is low; flashes
while recharging, and stays on aer fully charged
Condenser MIC: built-in gold-plated diaphragm condenser capsule with
omni-direconal pickup
MIC IN socket
Ⅱ.Userinterfaceofreceiver(RX)
—2—
IPSdisplayofreceiver
Ⅲ.Storagebox
—3—
Ⅳ.Matching
(TX)Transmier (RX)Receiver
—4—
—5—
1. TX: at power-off state, press and hold the power buon unl the
transmier is on and the connecon status indicator flashes to enter the
matching mode (if there are two TXs, just operate same as above); then go
to step 2.
2. RX: at power-off state, press and hold the power buon unl the receiver
is on and the wireless signal indicator flashes to enter the matching
mode; aer 3-5 seconds, the indicator of both TX and RX stop flashing, the
matching is complete.
V.Startusing
RX-Howtouseoncellphone: RX-Howtouseonotherdevices:
—6— —7—
—8— —9—
Ⅶ.Specificaons
· Frequency range: 2402 - 2480 MHZ
· Modula on: GFSK
· Transmit power: ≤ 17 dBm
· Low-cut: 100 Hz
· DSP noise cancelling: -6 dB
· Power supply：3.7V (built-in Li-baery)
· Charging input: 5V 1A
· Charging period: ≈2hrs
· Opera ng me: approx. 7 hrs
· Power management: shut down automa cally aer 5-10 minutes no connec
on,
or shut down automacally when placed in the storage box
· Operang temperature: 0°C to 55°C
· Storage temperature: -20°C to +55°C
· Dimensions: 44 * 43 * 14 mm (TX); 56 * 43 * 18 mm (RX)
· Net weight: approx. 26 g (TX); approx. 40 g (RX)
Storage box:
◇ Theimageshownhereisindicaveonly.Ifthereisinconsistency
betweentheimageandtheactualproduct,theactualproductshall
govern.
◇ MAILADAreservestherightstoimproveproductandproduct
copyrightinformaonwithoutpriornoce.
Version:V1.0-2022-5
WhenTXandRXcannotbeconnected,followthestepsbelowtore-matching:
Type-C socket
iPhone
Transmier 2×
×1Receiver
×1Storage box
×1Storage bag
×2Lavalier microphone
×1Type-C OTG audio cable
×1Camera audio cable
×1Type-C recharging cable
×2Furry windscreen
①
②
③
④
⑤
⑥
⑦
Headphone output
Camera audio output: for connecng the receiver to recording device
such as camera
Charging/OTG socket: for charging input and OTG audio connecon
IPS display
Power buon: press and hold for 1 second to turn on or off
Volume buon: to adjust output volume level
Reset hole: use a needle tool to click the buon in the hole to restore
the factory default sengs
Sound effect buon: provides three oponal sound effect modes – LOW
CUT, DSP acve noise reducon, KTV (ECHO)
①
②
③
④
⑤
⑥
⑦
⑧
◇ Press and hold buon⑥and⑧at the same me for more than 2 seconds
to switch between M (mixed output mode), ST (stereo outputmode), Ms (safe
track mode)
◇ At ST (Stereo Output) mode, no KTV (ECHO) effect available
Transmier channel indicator: lights in green means the transmier was
connected; lights in white means no connecon
Transmier baery level indicator
Wireless signal indicator
Receiver baery level indicator
Output volume level
Audio level: displays the microphone audio signal
Current sound effect mode: is at LOW CUT mode for improving vocal
clarity; is DSP acve noise reducon to eliminate ambient noise;
is ECHO reverb effect to improve vocal fullness and space sense
Output mode: M is mixed output, namely band 1 and 2 are all mixed on
both the le and right channel; ST is stereo output (band 1 is the le
channel output, while band 2 is the right channel output); Ms is safe track
output - the right channel output is 6 dB less than the le channel
USB connecon: this icon will show up when the cell phone or computer is
successfully connected through the OTG audio cable
①
②
③
④
⑤
⑥
⑦
⑧
⑨
Charging socket
Status indicator: indicates baery level and charging status
Funcon buon: single-click to force turn-on, double-click to force shutdown
Wireless charging area: wireless charging funcon available, and the
inducon coil is located at the boom of the storage box (see the indicated
doed line area)
①
②
③
④
Long press the power buon of the TX and RX to turn on
Clip the TX on the collar
Mount the RX on the camera
Connect the OUT socket of the RX with the “MIC IN” socket of the
camera by using the 3.5mm camera audio cable
Set the RX output volume at level 3-4, and set the recording volume of the
camera at rather minimum volume to avoid distoron during recording, so
as to assure the opmum effect
①
②
③
④
⑤
(TX) Transmier
(RX) Receiver
(RX) Receiver
(RX) Receiver
Type-C socket
Connect the Type-C socket of the RX with the Type-C socket of the cell
phone by using the Type-C OTG audio cable
*ForsomecellphoneswithType-Csocket,youneedtoturnontheOTG
funconinthephonesengseconinordertousetheType-Caudio
cablenormally
Connect the Type-C socket of the RX with the Lightning socket of the cell
phone by using the Lightning OTG audio cable
①
②
Type-C OTG audio cable
Lightning OTG audio cable
Android
Type-C socket
OUT socket
(RX) Receiver
(RX) Receiver
Type-C OTG audio cable
3.5mm camera audio cable
MIC IN socket
Mx1 PLUS Portable Live Streaming Interfance
Laptop
Connect the Type-C socket of the RX with the Type-C/USB socket of the
laptop by using the Type-C OTG audio cable
Connect the OUT socket of the RX with the “MIC IN” or “LINE IN”
socket of the audio interface by using the 3.5mm camera audio cable
①
②
When not using for a long me, the built-in rechargeable baery should be
fully charged every three months to maintain the high performance of the
baery.
The built-in baery must not be exposed to sunlight, fire, or similar
overheang environment.
To avoid intermient signal, please try to keep the transmier and receiver
face to face while using.
2.
3.
4.
Ⅵ.Precautions
This product is a precise electronic device, which should avoid watering
or heavy fall; if it gets wet, please dry it in me, and hand it up to
professional technician for further checking.
1.
As shown below:
Face to face(correct)
Reverse direcon(wrong)
· Type C charging input: 5V 2A
· Wireless charging input: 5V 1A (electromagnec inducon)
· Power supply: 3.7V/3200mAh (built-in Li-baery)
· Dimensions: 121 * 61 * 59 mm
· Net weight: approx. 188 g
· Operang temperature: 0 °C to 55°C
· Storage temperature: -20°C to +55°C
① ② ③ ④
⑤ ⑥ ⑦ ⑧ ⑨
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.