User’s Guide Learn how to use your Fujitsu LifeBook T730 Tablet PC
Copyright and Trademark Information Fujitsu America, Inc. has made every effort to ensure the accuracy and completeness of this document; however, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes. Fujitsu, the Fujitsu logo, and LifeBook are registered trademarks of Fujitsu Limited.
WARNING HANDLING THE CORD ON THIS PRODUCT WILL EXPOSE YOU TO LEAD, A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER HANDLING. © Copyright 2010 Fujitsu America, Incorporated. All rights reserved. No part of this publication may be copied, reproduced, or translated, without prior written consent of Fujitsu. No part of this publication may be stored or transmitted in any electronic form without the written consent of Fujitsu.
IMPORTANT SAFETY INSTRUCTIONS This unit requires an AC adapter to operate. Use only UL Listed I.T.E. Class II Adapters with an output rating of 19 VDC, with a current of 4.22 A (80 W). + AC adapter output polarity: When using your notebook equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: • CAUTION - HOT SURFACE: The bottom of this notebook computer can become hot when used for long periods of time.
Recycling your battery Over time, the batteries that run your mobile computer will begin to hold a charge for a shorter amount of time; this is a natural occurrence for all batteries. When this occurs, you may want to replace the battery with a fresh one*. If you replace it, it is important that you dispose of the old battery properly because batteries contain materials that could cause environmental damage if disposed of improperly.
Contents Preface About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Conventions Used in the Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Fujitsu Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Chapter 1 Getting to Know Your LifeBook Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Opening the Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Using the System as a Tablet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Adjusting Display Panel Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Enabling/Disabling Ambient Light Sensor (Windows 7 only). . . . . . . . . . 38 Keyboard . . .
Chapter 2 Getting Started with Your LifeBook Power Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Connecting the Power Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Starting Your LifeBook Tablet PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Boot Sequence . . . . . . . . . . . . . . .
ExpressCards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Installing ExpressCards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Removing ExpressCards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Memory Upgrade Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Installing Memory Upgrade Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 4 Troubleshooting Your LifeBook Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Identifying the Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Specific Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 Power On Self Test Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 Restoring Your Pre-installed Software . .
Mass Storage Device Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Modular Bay Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting the WLAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 WLAN Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 Using the Bluetooth Device. . . . . . . . . . . . . . . . . . . . . . . . . .
Preface About This Guide The LifeBook T730 Tablet PC from Fujitsu America is a powerful convertible computer. It can be used either as a standard notebook using keyboard input, or in tablet configuration using pen input. It is powered by an all new 2010 Intel® Core™ Processor , has a built-in color display with either an active digitizer or optional dual digitizer, and brings the computing power of desktop personal computers to a portable and versatile environment.
THE INFORMATION ICON HIGHLIGHTS INFORMATION THAT WILL ENHANCE YOUR UNDERSTANDING OF THE SUBJECT MATERIAL. THE CAUTION ICON HIGHLIGHTS INFORMATION THAT IS IMPORTANT TO THE SAFE OPERATION OF YOUR PLEASE READ ALL CAUTION INFORMATION CAREFULLY. COMPUTER, OR TO THE INTEGRITY OF YOUR FILES. THE WARNING ICON HIGHLIGHTS INFORMATION THAT CAN BE HAZARDOUS TO EITHER YOU, YOUR LIFEBOOK TABLET PC, OR YOUR FILES. PLEASE READ ALL WARNING INFORMATION CAREFULLY.
• Conditions under which the problem occurred • Any error messages that have occurred • Type of device connected, if any Fujitsu Shopping Online You can go directly to the online store by going to the website at: www.shopfujitsu.com. YOU MUST HAVE AN ACTIVE INTERNET CONNECTION TO USE THE ONLINE URL LINKS. Limited Warranty Your LifeBook T730 Tablet PC is backed by a Fujitsu International Limited Warranty.
Chapter 1 Getting to Know Your LifeBook Overview This section describes the components of your Fujitsu LifeBook T730 Tablet PC. We strongly recommend that you read it before using your Tablet PC – even if you are already familiar with notebook computers. Figure 1.
Locating the Controls and Connectors Connectors and peripheral interfaces on the LifeBook T730 Tablet PC and the optional port replicator allow you to connect a variety of devices. Specific locations are illustrated in Figures 2 through 6. The table below provides a short description of each icon on the LifeBook T730 Tablet PC and/or optional port replicator. Each of the icons is either molded into or printed on the Tablet PC or port replicator chassis.
Connection Tablet PC Icon Purpose Security lock slot The security slot allows you to secure the Tablet PC using compatible locking devices. Suspend/ Resume button The Suspend/Resume button allows you to suspend Tablet PC activity without powering off, resume your Tablet PC from suspend mode, and power on the system when it has been shut down from Windows.
Display Latch Optional Web Cam Built-in Microphone Stereo Speaker Display Panel Fingerprint Sensor Stereo Speaker LifeBook Security/ Tablet PC Buttons Touchpad Cursor Control Power/Suspend/ Resume Switch Status Indicator Panel Ambient Light Sensor Headphone Jack Microphone Jack Built-in Microphone Status Indicator Panel IEEE 1394 Jack Wireless LAN/Bluetooth/ On/Off Switch Memory Stick/ SD Card Slot Keyboard Display Latch Button Figure 2.
Top Components The following is a brief description of your LifeBook Tablet PC’s top components. Display Latch The display latch is used to secure the tablet PC display when it is closed. Web Camera The optional 2.0 megapixel web cam can be used to take pictures of yourself to send over the internet. Display Panel The display panel is a color LED panel with backlighting for the display of text and graphics.
Status Indicator Panels The Status Indicator Panels display symbols that correspond to specific components of your Tablet PC. Status indicators are located in two locations: on the left front edge of the system (system status indicators) and below the application buttons (button status indicators). See “Status Indicator Panel” on page 30. Keyboard A full-size keyboard with dedicated Windows keys. See “Keyboard” on page 38.
Headphone Jack The headphone jack allows you to connect headphones. See “Headphone Jack” on page 101. Touchpad Pointing Device The Touchpad pointing device is a mouse-like cursor control with a left and right button. See “Touchpad/Active Digitizer/Touchscreen” on page 41. Fingerprint Sensor The fingerprint sensor device allows you to log onto your system and password-protected websites and applications by swiping your finger over the sensor. See “Introducing the Fingerprint Sensor Device” on page 177.
ExpressCard Slot ExpressCard Eject Button DC Power Jack USB 2.0 Port Air Vents Figure 3. LifeBook Tablet PC left-side panel Left-Side Panel Components The following is a brief description of your LifeBook Tablet PC’s left-side components. DC Power Jack The DC power jack allows you to plug in the AC adapter to power your LifeBook Tablet PC and charge the internal Lithium ion battery. USB 2.0 Ports The USB 2.
TO PROTECT YOUR TABLET PC FROM DAMAGE AND TO OPTIMIZE PERFORMANCE, BE SURE TO KEEP ALL THIS MAY REQUIRE PERIODIC CLEANING, DEPENDING UPON THE ENVIRONMENT IN WHICH THE SYSTEM IS USED. AIR VENTS UNOBSTRUCTED, CLEAN, AND CLEAR OF DEBRIS. DO NOT OPERATE THE TABLET PC IN AREAS WHERE THE AIR VENTS CAN BE OBSTRUCTED, SUCH AS IN TIGHT ENCLOSURES OR ON SOFT SURFACES LIKE A BED OR CUSHION. ExpressCard Slot The ExpressCard Slot allows you to install an ExpressCard. See “ExpressCards” on page 88.
Pen Garage Pen Tether Attachment Point Modular Bay Modular Bay Release Latch Figure 4. LifeBook Tablet PC right-side panel Right-Side Panel Components The following is a brief description of your LifeBook Tablet PC’s right-side components. Pen Garage The pen garage is used to store the pen (also called a “stylus”) when not in use.The pen is used as the interface with the active digitizer display. Modular Bay The Modular Bay can accommodate one of the following devices.
Anti-Theft Lock Slot Air Vents Gigabit LAN (RJ-45) Jack HDMI Port External Video Port USB 2.0 Ports Figure 5. LifeBook Tablet PC back panel Back Panel Components Following is a brief description of your LifeBook Tablet PC’s back panel components. Anti-theft Lock Slot The anti-theft lock slot allows you to attach an optional physical lock down device. Air Vents The air vents allow air to circulate through the system to cool down the components.
TO PROTECT YOUR TABLET PC FROM DAMAGE AND TO OPTIMIZE PERFORMANCE, BE SURE TO KEEP ALL THIS MAY REQUIRE PERIODIC CLEANING, DEPENDING UPON THE ENVIRONMENT IN WHICH THE SYSTEM IS USED. AIR VENTS UNOBSTRUCTED, CLEAN, AND CLEAR OF DEBRIS. DO NOT OPERATE THE TABLET PC IN AREAS WHERE THE AIR VENTS CAN BE OBSTRUCTED, SUCH AS IN TIGHT ENCLOSURES OR ON SOFT SURFACES LIKE A BED OR CUSHION. External Video Port The external monitor port allows you to connect an external monitor or LCD projector.
Port Replicator Connector Memory Upgrade Compartment Dust Filter Battery Latch Battery Latch Lithium ion Battery Bay Air Vents Figure 6. LifeBook Tablet PC bottom panel Bottom Components The following is a brief description of your LifeBook Tablet PC’s bottom panel components. Memory Upgrade Compartment Your Tablet PC comes with high speed Double Data Rate 3 Synchronous Dynamic RAM (DDR3 1066 MHz SDRAM).
Port Replicator Connector This connector allows you to connect the optional Port Replicator to your Tablet PC. Dust Filter The dust filter is used to help remove dust and dirt from your system. See “Cleaning the dust filter” on page 129. Air Vents The air vents allow air to circulate through the system to cool down the components. TO PROTECT YOUR TABLET PC FROM DAMAGE AND TO OPTIMIZE SYSTEM PERFORMANCE, BE SURE TO KEEP ALL AIR VENTS UNOBSTRUCTED, CLEAN, AND CLEAR OF DEBRIS.
Security NumLk CapsLk ScrLk Optical/Hard Batt 1 Level Batt 2 Level Drive Access External Power Batt 1 Charging Batt 2 Charging Power Figure 7. Status Indicator Panel Status Indicator Panel The Status Indicator Panel displays symbols and associated LEDs that correspond to specific components of your Tablet PC. These symbols tell you how each of those components is operating.(Figure 7) Power Indicator • The Power indicator symbol shows whether your system is operational.
• Steady Off: This means that your system is either in Hibernate mode, or that your Tablet PC has been turned off. If you are charging your battery, the Power indicator symbol will remain on even if your LifeBook Tablet PC is shut off.
• Red, solid: Battery is between 0% and 12% charged. • Orange, blinking: Blinks during battery status measurement (Four seconds after the battery is installed). • Red, blinking: There is a problem with the battery. • Off: There is no battery installed. • If the battery pack is installed while the power is turned off, the battery level indicator will display the charge level for five seconds after it blinks orange.
Figure 8. Opening the Display Panel Display Panel Your LifeBook T730 Tablet PC contains an LED display panel that is backlit for easier viewing in bright environments. The convertible design of your Tablet PC allows you to open the display fully, rotate it in either direction 180 degrees, and lay it face up on the keyboard. This allows you to use the system as a tablet, much as you would a pad of paper.
Using the System as a Tablet If you would like to use the system as a tablet, perform the following steps. • The display can be rotated in either direction, but when returning the system to notebook mode, be sure to turn it back to its original position (i.e., the reverse of how you turned it when you opened it. Turning the display in the incorrect direction could cause hinge damage.
3 Holding the top edge of the display panel, pull it forward until it is lying atop the keyboard with the display facing the keyboard Figure 10. Fully Open Display Figure 11. Rotating Display Figure 12. Tablet Mode Adjusting Display Panel Brightness Once you have turned on your Tablet PC, you may want to adjust the brightness level of the screen to a more comfortable viewing level. There are three ways to adjust the brightness: keyboard, power management utility, and Fujitsu Menu.
Using Power Management to Adjust Brightness (Windows 7) Windows 7: To adjust brightness with the power management utility in Windows 7: Click Start -> Control Panel. In View by:, select one of the icon views. Select Display, then click Adjust brightness in the left pane. Drag Screen brightness: bar to the left or right, depending on your preference.
4 For more information about the light sensor, click on Light Sensor in the Sensor column to open the Sensor Properties window. 5 From the Sensor Properties window, you can change the sensor’s description, uninstall the sensor, or enable or disable selected users. • To change the sensor’s description, click the [Change description] button, enter the new description, and click the [OK] button.
Keyboard Function Keys Fn Key Start Key Numeric Keypad (surrounded by heavy line) Application Key Cursor Keys Figure 13. Keyboard Using the Keyboard Your Fujitsu LifeBook Tablet PC has an integral 84-key keyboard. The keys perform all the standard functions of a 101-key keyboard, including the Windows keys and other special function keys.
• Function keys: The keys labeled [F1] through [F12], are used in conjunction with the [Fn] key to produce special actions that vary depending on what program is running. • Windows keys: These keys work with your Windows operating system and function the same as the onscreen Start menu button, or the right button on your pointing device. Numeric Keypad Certain keys on the keyboard perform dual functions as both standard character keys and numeric keypad keys.
• [Fn+F3]: Pressing [F3] while holding [Fn] will toggle the Audio Mute on and off. • [Fn+F4]: Pressing [F4] while holding [Fn] will toggle the Quick Point feature on and off. Note that the [Fn+F4] combination only works if Manual Setting is selected in the BIOS. (See “BIOS Setup Utility” on page 71) • [Fn+F6]: Pressing [F6] repeatedly while holding [Fn] will lower the brightness of your display. • [Fn+F7]: Pressing [F7] repeatedly while holding [Fn] will increase the brightness of the display.
Touchpad/Active Digitizer/Touchscreen Scroll Sensor Figure 14. Touchpad pointing device Using the Touchpad The touchpad is built into your LifeBook Tablet PC. It is used to control the movement of the cursor to select items on your display panel. The touchpad is composed of a cursor control below the center of the keyboard, two buttons below it, and a scroll sensor on the right edge of the cursor control.
Clicking Clicking means pushing and releasing a button. To left-click, move the cursor to the item you wish to select, press the left button once, and then immediately release it. To right-click, move the mouse cursor to the item you wish to select, press the right button once, and then immediately release it. You also have the option to perform the clicking operation by tapping lightly on the touchpad once. Figure 16. Clicking with Touchpad Figure 15.
Double-Clicking Double-clicking means pushing and releasing the left button twice in rapid succession. This procedure does not function with the right button. To double-click, move the cursor to the item you wish to select, press the left button twice, and immediately release it. You can also perform the double-click operation by tapping lightly on the Touchpad twice. Figure 18. Double-clicking with button Figure 19.
Dragging Dragging means pressing and holding the left button, while moving the cursor. To drag, move the cursor to the item you wish to move. Press and hold the left button while moving the item to its new location and then release it. Dragging can also be done using the Touchpad. First, tap the Touchpad twice over the item you wish to move making sure to leave your finger on the pad after the final tap.
Scrolling Using the scrolling strip allows you to navigate through a document quickly without using the window’s scroll bars. This is particularly useful when you are navigating through on-line pages. To scroll, slide your finger up and down the scroll strip on the right side of the cursor control pad. Figure 22. Scrolling with the Scroll Strip Touchpad Control Adjustment The Windows Control Panel allows you to customize your touchpad with selections made from within the Mouse Properties dialog box.
Active Digitizer Display NOTE: Depending upon your system configuration, in addition to the active digitizer, you may also have a capacitive touch panel that responds to finger touch and touch gestures. (This configuration is called a “Dual Digitizer”.) For more information about the touchscreen, refer to “Using the Optional Capacitive Touchscreen” on page 50. The integrated active digitizer allows you to use the included stylus as a pointing device.
Clicking on Active Digitizer Display To left-click, touch the object you wish to select and then lift the stylus tip immediately. Figure 25. Right-clicking Active Digitizer Right-Clicking on Active Digitizer Figure 24. Clicking on the Active Digitizer Display Right-click can be accomplished by holding the front of the toggle button down while tapping on the screen. To change the settings for the rightclick feature, go to Start -> Control Panel -> Pen and Input Devices.
Double-Clicking To double-click, touch the item twice, and then immediately remove the stylus tip. Figure 26. Double-clicking the Display Dragging Dragging means moving an item with the stylus by touching the screen, moving and then lifting the stylus. To drag, touch the Active Digitizer Display with your stylus on the item you wish to move.
Calibrating the Active Digitizer Display In order to ensure accurate tracking between the stylus and cursor, you must run the Calibration Utility before you use the system for the first time, or after you change the display resolution. To run the calibration utility: 1 2 3 4 Go to Start -> Settings -> Control Panel. Double-click the Tablet PC Settings icon and select the General tab Click the [Calibrate] button.
Using the Optional Capacitive Touchscreen Certain configurations of this Tablet PC have an optional dual digitizer that allows you to use either the stylus or your finger(s) as a pointing device. This type of display also allows you to use “gestures” to perform such actions as scroll, zoom, and rotate. • GESTURE SUPPORT IS DETERMINED BY THE APPLICATION IN USE. • THE STYLUS TAKES PRECEDENCE OVER FINGER TOUCH. IF THE STYLUS IS WITHIN ACTIVE RANGE OF THE SCREEN, FINGER TOUCH WILL BE DISABLED.
Installing a Pen Tether To prevent dropping or losing your pen, you should attach it to your system using the pen tether that is included with the system. To attach the pen tether to your Tablet PC, perform the following steps: 1 Attach the end of the pen tether with the smaller loop to your pen. To do so, push the end of the tether through the hole in the pen, then thread the opposite end of the tether through the loop.
Volume Control Your Fujitsu LifeBook Tablet PC has multiple volume controls which interact with each other. ANY SOFTWARE THAT CONTAINS AUDIO FILES WILL ALSO CONTAIN A VOLUME CONTROL OF ITS OWN. IF YOU INSTALL AN EXTERNAL AUDIO DEVICE THAT HAS AN INDEPENDENT VOLUME CONTROL, THE HARDWARE VOLUME CONTROL AND THE SOFTWARE VOLUME CONTROL WILL INTERACT WITH EACH OTHER. IT SHOULD BE NOTED THAT IF YOU SET YOUR SOFTWARE VOLUME TO OFF, YOU WILL OVERRIDE THE EXTERNAL VOLUME CONTROL SETTING.
Modular Bay Modular Bay Release Latch Figure 29. Modular Bay Modular Bay Devices Your Fujitsu LifeBook Tablet PC contains a Modular Bay. The Modular Bay can house an optical drive, a Lithium ion battery, a modular second hard disk drive and a weight saver. Your Modular Bay will have one of the following devices installed. • Modular Dual-Layer Multi-Format DVD Writer: This allows you to access movies, software, and audio DVD/CDs and record to DVD, CD, and DVD-RAM discs.
Removing and Installing Modular Devices There are two ways to remove and install modular devices in the Modular Bay: • Cold-swapping: swapping devices while your LifeBook Tablet PC is powered off. • Hot-swapping: swapping devices while your system is active using the Safely Remove Hardware icon from your system tray. Cold-swapping To cold-swap modular devices in your Modular Bay follow these easy steps: 1 2 3 Close any open files.
Figure 31. LifeBook T730 Tablet PC Security/Tablet PC Buttons LifeBook Security/Tablet PC Buttons A unique feature of your LifeBook T730 Tablet PC is the array of Security and Tablet PC buttons. These buttons allow you to secure your Tablet PC from unauthorized use and to launch specific applications and functions with the touch of a button.
All five buttons are used when implementing security functions. Four of the buttons are used to enter the password, and the fifth is used as an Enter button. See Table 1 for information about each of the Security buttons. Button Icon System State System is pre-boot or resuming from suspend Security Panel Function Security Button 1 Security Button 2 Security Button 3 Security Button 4 Security Enter Button Table 1.
/ When you press the [Page Up] button when the system is pre-logon, each press of the button will act as if you had pressed the [Enter] key. Button Icon System State System is prelogon (Windows logon screen is displayed) Tablet PC Function Secondary Functions (Fn + Button) Rotate screen None Used to invoke secondary function None Ctl+Alt+Del Button None Table 2.
THE SCREEN ORIENTATION DEFAULT CAN BE CHANGED BY GOING TO THE CONTROL PANEL AND DOUBLE-CLICKING ON THE FUJITSU TABLET CONTROLS ICON AND SELECTING THE DESIRED SETTINGS IN THE DISPLAY PROPERTIES. AFTER CHANGING THE SETTINGS, SAVE THEM IN FUJITSU TABLET CONTROLS. When you press the [Screen Rotation] button when the system is in pre-boot, the system screen orientation changes from portrait (vertical) to landscape (horizontal) or from landscape to portrait.
When you press the [Fn] button then press and release the [Page Up/Application B] button, you will automatically start whichever program is assigned to the button. The default application for this button is Microsoft Journal. See “Changing Tablet PC Button Functions” on page 60 to select a different application for this button.
THE SCREEN ORIENTATION DEFAULT CAN BE CHANGED BY GOING TO THE CONTROL PANEL AND PC SETTINGS ICON AND SELECTING THE DESIRED SETTINGS IN THE DISPLAY TAB. AFTER CHANGING THE SETTINGS, SAVE THEM IN FUJITSU TABLET CONTROLS. DOUBLE-CLICKING ON THE TABLET When you press the [Screen Rotation /Display Switching] button, the system screen orientation changes from portrait (vertical) to landscape (horizontal) or from landscape to portrait.
3 4 Click [Change] and open the drop down list in the Press: field. 5 Click [OK], then click [OK] again. The buttons will now perform the actions you have assigned to them. Select the action you would like the button to perform. If you want to launch a program, click on Launch an Application then browse to the location of the program. Setting up LifeBook Security Panel When you receive your Tablet PC, the security panel application is pre-installed without any passwords.
The following are valid passwords. The numbers within braces ({ }) are button strokes using more than one button. • {[2]+[3]}, [1], [Enter] • [4], [enter] • {[1]+[3]}, {[2]+[3]+[4]}, [1], [4], [2], [Enter] Setting Passwords When shipped from the factory, no passwords are set. You have a choice of having no password or setting a supervisor and user password. You must set the supervisor password before the user password.
YOU MAY CHANGE OR REMOVE THE SUPERVISOR OR USER PASSWORD BY REPEATING THE STEPS DEFINED ABOVE. Using Your LifeBook Security Panel The security lock feature is in effect both when the system resumes from Off, Sleep, or Hibernation state. You always need to push the Security Panel buttons to input the user password. Your system will not begin the boot sequence until you enter your supervisor/user password. From Off State 1 2 Turn on your system.
REMEMBER THE USER PASSWORD YOU SPECIFIED ON THE SECURITY PANEL APPLICATION. IF YOU THE SUPERVISOR PASSWORD CAN OVERRIDE THE USER PASSWORD. FORGET THE PASSWORD YOU WILL NOT BE ABLE TO USE YOUR COMPUTER. Precautions Opening and Closing the Cover By default, closing the cover automatically places your system into Sleep mode. To change the default when the cover is closed: 1 2 3 Open the system Control Panel and select Power Options. (Windows XP: Select the Advanced tab).
Uninstalling the Security Panel Application Software Remove passwords when User wants no password protection whatsoever and doesn’t want to give anybody the utility to set a password on their computer. In this case, if passwords (supervisor, user, or both) are set, the passwords must first be cleared BEFORE removing the application. To clear passwords, follow same procedure in SETTING PASSWORD CODES except this time, select REMOVE, enter current password then click Next. When asked to confirm select Yes.
Reinstalling the Security Panel Application To reinstall supervisor or user security application, you will need your Drivers and Applications CD. The Utilities\Security Panel Application folder contains two separate folders: Supervisor and User. The setup files for supervisor and user security applications are contained in those folders. 1 Go to the Utilities\Security Panel Application\ Supervisor folder on the CD and double-click the setup.exe file.
Chapter 2 Getting Started with Your LifeBook Power Sources Your Fujitsu LifeBook Tablet PC has three possible power sources: a primary Lithium ion battery, an AC adapter or an optional Auto/Airline adapter. Connecting the Power Adapters The AC adapter or optional Auto/Airline adapter provides power for operating your Tablet PC and charging the batteries. Connecting the AC Adapter 1 Plug the DC output cable into the DC power jack of your LifeBook Tablet PC.
AC Adapter DC Power Jack Figure 32. Connecting the AC Adapter Switching from AC Adapter Power or the Auto/Airline Adapter to Battery Power 1 2 Be sure that you have at least one charged battery installed. Remove the AC adapter or the Auto/Airline adapter. THE LITHIUM ION BATTERY IS NOT CHARGED UPON PURCHASE. INITIALLY, YOU WILL NEED TO CONNECT AC ADAPTER OR THE AUTO/AIRLINE ADAPTER TO USE YOUR TABLET PC.
Starting Your LifeBook Tablet PC Power On Power/Suspend/Resume Button The Power/Suspend/Resume button is used to turn on your LifeBook Tablet PC from its off state. Once you have connected your AC adapter or charged the internal Lithium ion battery, you can power on your LifeBook Tablet PC. WHEN YOU TURN ON YOUR LIFEBOOK TABLET PC BE SURE YOU HAVE A POWER SOURCE. THIS MEANS AC OR AUTO/AIRLINE ADAPTER IS CONNECTED AND HAS POWER.
DO NOT CARRY YOUR LIFEBOOK TABLET PC AROUND WITH THE POWER ON OR SUBJECT IT TO SHOCKS OR VIBRATION, AS YOU RISK DAMAGING YOUR TABLET PC. When you power on your LifeBook, it will perform a Power On Self Test (POST) to check the internal parts and configuration for correct functionality. If a fault is found, your LifeBook Tablet PC will emit an audio warning and/or an error message will be displayed. See “Power On Self Test Messages” on page 116.
The boot sequence is executed when: • You turn on the power to your LifeBook Tablet PC. • You restart your Tablet PC from the Windows Shut Down dialog box. • The software initiates a system restart. Example: When you install a new application. Hard Disk Drive Passwords To provide additional security for your data, you can assign passwords to your hard disk drive(s). This feature is managed in the system BIOS Setup Utility. See BIOS Setup Utility below for information about accessing the utility.
3 Press the [RIGHT ARROW] or [LEFT ARROW] key to scroll through the other setup menus to review or alter the current settings. Using the TrustedCore Menu When the Fujitsu logo appears on the screen. press the [Enter] key or click on the left mouse or touchpad button; the TrustedCore Menu will appear.
Starting Windows the first time THE FIRST TIME YOU INITIALIZE YOUR WINDOWS SYSTEM, THE SCREEN WILL BE BLANK FOR APPROXIMATELY TWO MINUTES. THIS IS NORMAL. AFTER INITIALIZATION, A “SET UP WINDOWS” DIALOG BOX WILL APPEAR. IMPORTANT: DURING THE SETUP PROCEDURE, DO NOT DISCONNECT THE POWER SUPPLY, PRESS ANY BUTTONS, OR USE ANY PERIPHERAL DEVICES SUCH AS A MOUSE, KEYBOARD, OR REMOTE CONTROL.
7 The "Thank you" screen follows and an offer for free Norton Internet Security is extended. Following are several screens while Windows checks the system performance. 8 Windows will then boot up for the first time. As noted above, the first time you initialize your system, the screen will be blank for approximately two minutes. This is normal. During this period, do not disconnect the power supply, press any buttons, or use any peripheral devices such as mouse, keyboard, or remote control.
THERE MAY BE SOME THIRD-PARTY APPLICATIONS THAT DO NOT GET INSTALLED USING THE CLICKME! UTILITY. FOR MORE INFORMATION, REFER TO YOUR GETTING STARTED GUIDE. Fujitsu Driver Update Utility Your system has a convenient tool called the Fujitsu Driver Update (FDU) utility. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system. For more information about the FDU utility, refer to “Automatically Downloading Driver Updates” on page 124.
Power Management Your Fujitsu LifeBook Tablet PC has many options and features for conserving battery power. Some of these features are automatic and need no user intervention. However, others depend on the parameters you set to best suit your operating conditions, such as those for the display brightness. Internal power management for your Tablet PC may be controlled from settings made in your operating system, prebundled power management application, or from settings made in BIOS setup utility.
• Selecting “Sleep” after clicking [Start] then clicking the small arrow at the bottom right of the window. • Timing out from lack of activity. • Allowing the battery to reach the Dead Battery Warning condition. Your Tablet PC’s system memory typically stores the file on which you are working, open application information, and any other data required to support operations in progress. When you resume operation from Sleep mode, your Tablet PC will return to the point where it left off.
Hibernation (Save-to-Disk) Feature The Hibernation feature saves the contents of your Tablet PC’s system memory to the hard drive as a part of the Suspend/Resume mode. You can enable or disable this feature. Enable or Disable the Hibernation Feature The default settings are not enabled. To enable or disable the Hibernation feature follow these steps: 1 2 From the Start menu, select Control Panel, then select the Power Options icon.
Powering Off Before turning off the power, check that the hard drive/optical drive access indicator is off. If you turn off the power while accessing a disk there is a risk of data loss. To ensure that your Tablet PC shuts down without error, use the Windows shut down procedure. BE SURE TO CLOSE ALL FILES, EXIT ALL APPLICATIONS, AND SHUT DOWN YOUR OPERATING SYSTEM PRIOR TO TURNING OFF THE POWER.
Sleep Mode: You will notice that your computer is initially set so that the display turns off after 15 minutes of user inactivity, and the computer goes into Sleep mode after 20 minutes of user inactivity. When going into Sleep mode, the computer also reduces the speed of any active Ethernet network links. To “wake” the computer from Sleep mode, press the Suspend/Resume Button.
Chapter 3 User-Installable Features Lithium ion Battery Your LifeBook Tablet PC has a Lithium ion battery that provides power for operating your Tablet PC when no external power source is available. The battery is durable and long lasting, but should not be exposed to extreme temperatures, high voltages, chemicals or other hazards.
• ACTUAL BATTERY LIFE WILL VARY BASED ON SCREEN BRIGHTNESS, APPLICATIONS, FEATURES, POWER MANAGEMENT SETTINGS, BATTERY CONDITION AND OTHER CUSTOMER PREFERENCES. OPTICAL DRIVE THE BATTERY CHARGING CAPACITY IS REDUCED AS THE BATTERY AGES. IF YOUR BATTERY IS RUNNING LOW QUICKLY, YOU SHOULD REPLACE IT WITH A NEW ONE. OR HARD DRIVE USAGE MAY ALSO HAVE A SIGNIFICANT IMPACT ON BATTERY LIFE. • UNDER FEDERAL, STATE, OR LOCAL LAW IT MAY BE ILLEGAL TO DISPOSE OF BATTERIES BY PUTTING THEM IN THE TRASH.
USING HEAVY CURRENT DEVICES OR FREQUENT EXTERNAL OPTICAL DRIVE ACCESSES MAY PREVENT CHARGING COMPLETELY. Low Battery State When the battery is running low, a low battery notification message will appear. If you do not respond to the low battery message, the batteries will continue to discharge until they are too low to operate. When this happens, your Tablet PC will go into Sleep mode. There is no guarantee that your data will be saved once the Tablet PC reaches this point.
Shorted Batteries The Status Indicator panel indicator associated with the Battery Level indicator displays the operating level available in that battery. If this display shows a flashing red LED, it means the battery is damaged and must be replaced so it does not damage other parts of your LifeBook Tablet PC. Replacing the Battery With the purchase of an additional battery, you can have a fully charged spare to swap with one that is not charged.
Battery Pack Battery Bay Release Latches Figure 34. Removing a Battery 2 Follow steps 3 through 5 in “Cold Swapping Batteries”. IF THE LITHIUM ION BATTERY CONNECTOR IS NOT FULLY SEATED, YOU MAY NOT BE ABLE TO USE YOUR TABLET PC OR CHARGE YOUR BATTERY.
SD/Memory Stick Card Slot SD Card Memory Stick Figure 35. Installing a Memory Stick or SD Card Memory Stick/Secure Digital Cards Your LifeBook Tablet PC supports Memory Sticks and Secure Digital (SD) cards, on which you can store and transfer data to and from a variety of digital devices. These cards use flash memory architecture, which means they don’t need a power source to retain data.
Installing Memory Stick/SD Cards Memory Stick and SD Cards are installed in the Memory Stick/SD Card slot. To install a Memory Stick or SD Card, follow these steps: INSTALLING OR REMOVING A MEMORY STICK OR SD CARD DURING YOUR LIFEBOOK TABLET PC’S SHUTDOWN OR BOOTUP PROCESS MAY DAMAGE THE CARD AND/OR YOUR LIFEBOOK TABLET PC. DO NOT INSERT A CARD INTO A SLOT IF THERE IS WATER OR ANY OTHER SUBSTANCE ON THE CARD AS LIFEBOOK TABLET PC, OR BOTH.
ExpressCard Eject Button ExpressCard (54 mm) ExpressCard (34 mm) ExpressCard Slot Figure 36. Installing/Removing an ExpressCard ExpressCards Your LifeBook supports ExpressCardsTM which can perform a variety of functions depending on which type of card you install. There are two different width ExpressCards: 34 mm and 54 mm. The connector inside the slot is located on the left-hand side of the slot. If you insert a 34 mm card, be sure to align it with the left side of the slot when inserting it.
YOU MAY BE REQUIRED TO LOG ON AS ADMINISTRATOR OR A MEMBER OF THE ADMINISTRATOR’S GROUP TO COMPLETE THIS PROCEDURE. IF YOUR COMPUTER IS CONNECTED TO A NETWORK, NETWORK POLICY SETTINGS MAY ALSO PREVENT YOU FROM COMPLETING THIS PROCEDURE. See your ExpressCard manual for instructions on the installation of your card. Some cards may require that your notebook is off while installing them.
Memory Upgrade Module Your Fujitsu LifeBook Tablet PC comes with a minimum of 1 GB of high speed Double Data Rate Synchronous Dynamic RAM (DDR3-1066 SDRAM) factory installed. To increase your Tablet PC’s memory capacity, you may install an additional memory upgrade module. The memory upgrade must be a dual-in-line (DIMM) SDRAM module. To ensure 100% compatibility, purchase the SDRAM module only from the Fujitsu web store at www.shopfujitsu.com.
Retaining Clip Figure 37. Opening Memory Compartment Figure 38. Installing a Second Memory Module 7 Insert the memory upgrade module at a 45° angle. Press the connector edge of the module firmly down and into the connector until it lodges under the retaining clip. You’ll hear a click when it is properly in place. 8 Replace the cover and reinstall the screws. THE MEMORY UPGRADE MODULE IS NOT SOMETHING YOU ROUTINELY REMOVE FROM YOUR TABLET PC.
Removing a Memory Upgrade Module 1 2 3 4 Perform steps 1 through 4 of Installing a Memory Upgrade Module. Pull the clips sideways away from each side of the memory upgrade module at the same time. While holding the clips out, remove the module by lifting it up and pulling it away from your Tablet PC. Store the memory upgrade module in a static guarded sleeve. Replace the cover and reinstall the screws.
Media Holder Tray Emergency Tray Release Media Tray Eject Button Figure 39. Optical Drive Optical Drive There is a variety of media available to use with your Multi-Format DVD Writer, also known as an “optical drive”. DVD-R and DVD-RW discs hold up to 4.7 GB of data (DVD-R discs used with Multi-Format Dual-Layer DVD writer hold up to 8.5 GB). A DVD-R disc can only be written to once; DVD-RW discs can be written to over and over. DVD-R and DVD-RW discs can be played on most standard players.
• • DO NOT OPERATE YOUR OPTICAL DRIVE UNLESS YOUR LIFEBOOK NOTEBOOK IS SITTING ON A FLAT SURFACE. USING A DRIVE WHEN THE SYSTEM IS NOT LEVEL MAY DAMAGE THE DRIVE OR PREVENT PROPER OPERATION. PROLONGED USE OF THE OPTICAL DRIVE, SUCH AS WATCHING A DVD MOVIE, WILL SUBSTANTIALLY REDUCE YOUR BATTERY LIFE IF NO EXTERNAL POWER SOURCE IS ATTACHED. Loading Media on Your Drive To load a disc into your optical drive: 1 Push and release the eject button on the front of the optical drive to open the holder tray.
4 Gently push the holder tray back in until you hear a click IF YOU HAVE DISABLED THE AUTO INSERT NOTIFICATION FUNCTION, YOU WILL HAVE TO START THE MY COMPUTER OR FROM WITHIN WINDOWS EXPLORER, SINCE YOUR NOTEBOOK WILL NOT AUTOMATICALLY RECOGNIZE THAT MEDIA HAS BEEN LOADED. DRIVE EITHER BY USING b. a. c. d. Figure 40.
Removing Media 1 Push and release the eject button on the front of the optical drive. This will stop the drive and the holder tray will come out of the LifeBook notebook a short distance. 2 3 4 Gently pull the tray out until the disc can easily be removed from the tray. Carefully remove the media disc from the holder tray. Gently push the holder tray back in until you hear a click.
Starting a DVD Movie 1 2 Insert the DVD into the optical drive of the notebook. If the CD AutoRun feature activates, skip Step 2. 3 Click OK to close the About DVD Player Performance dialog box and the movie will begin. The first time you insert a movie into the DVD/CD-RW tray, you will be prompted to select what you want the system to do when discs are inserted (e.g., start automatically or wait for a prompt). Until you make a selection, you will receive the same prompt whenever you insert a disc.
Using Media Player on Battery Power Since optical drives consume a lot of power, your overall battery life will be significantly shorter when operating the optical drive continuously (such as watching a DVD movie) than during standard operation. • MANY MOVIE RUN-TIMES ARE LONGER THAN YOUR SYSTEM CAN SUPPORT ON A SINGLE BATTERY. IF YOU ARE WATCHING A DVD MOVIE ON BATTERY POWER YOU MAY NEED TO SWAP IN AN ADDITIONAL, AC POWER DURING THE MOVIE TO VIEW IT IN ITS ENTIRETY.
Device Ports Your Fujitsu LifeBook Tablet PC and the optional Port Replicator come equipped with multiple ports to which you can connect external devices including: disk drives, keyboards, printers, etc. Internal LAN (RJ-45) Jack The internal LAN (RJ-45) jack is used for a Gigabit (10Base-T/100Base-Tx/1000Base-T) Ethernet LAN connection. You may need to configure your Tablet PC to work with your particular network. (Please refer to your network administrator for information on your network configuration.
Universal Serial Bus Ports The Universal Serial Bus 2.0 ports (USB) allow you to connect USB devices such as external game pads, pointing devices, keyboards and/or speakers. There are three USB 2.0 ports on your Tablet PC: one on the left side and two on the rear.. In order to connect a USB device follow these steps: 1 2 Align the connector with the port opening. Push the connector into the port until it is seated. Figure 43.
THE 1394 PORT USED IN THIS SYSTEM USES A FOUR-PIN CONFIGURATION. IF YOU INTEND TO INTERFACE WITH DEVICES WHICH USE A SIX-PIN CONFIGURATION, YOU WILL NEED TO PURCHASE AN ADAPTER. In order to connect a 1394 device, follow these steps: 1 2 Align the connector with the port opening. Push the connector into the port until it is seated. IEEE 1394 Connector Figure 44.
Microphone Jack The microphone jack allows you to connect an external microphone. Your microphone must be equipped with a 1/8”(3.5 mm) mono mini-plug in order to fit into the microphone jack of your Tablet PC. In order to connect a microphone follow these easy steps: 1 Align the connector with the port opening and push the connector into the port until it is seated.
PRESSING THE [FN] + [F10] KEYS ALLOWS YOU TO CHANGE YOUR SELECTION OF WHERE TO SEND THE ORDER IS DETERMINED BY WHICH TYPE OF EXTERNAL VIDEO DEVICE(S) IS CONNECTED. EACH TIME YOU PRESS THE KEY COMBINATION, YOU WILL STEP TO THE NEXT CHOICE. YOUR DISPLAY VIDEO. IF YOU ONLY HAVE AN EXTERNAL CRT CONNECTED, THE ORDER IS: INTERNAL DISPLAY -> EXTERNAL CRT -> SIMULTANEOUS DISPLAY -> INTERNAL DISPLAY.
Chapter 4 Troubleshooting Your LifeBook Troubleshooting There may be occasions when you encounter simple setup or operating problems that you can solve on the spot, or problems with peripheral devices that can be solved by replacing the device. The information in this section helps you isolate and resolve some of these straightforward issues and identify failures that require service.
7 If the problem has not been resolved, refer to the Troubleshooting Table, that follows, for more detailed troubleshooting information. IF YOU KEEP NOTES ABOUT WHAT YOU HAVE TRIED, YOUR SUPPORT REPRESENTATIVE MAY BE ABLE TO HELP YOU MORE QUICKLY BY GIVING ADDITIONAL SUGGESTIONS OVER THE PHONE. 8 If you have tried the solutions suggested in the Troubleshooting Table without success, contact your support representative: Toll free: 1-800-8Fujitsu (1-800-838-5487) E-mail: 8fujitsu@us.fujitsu.
Specific Problems Using the Troubleshooting Table When you have problems with your LifeBook Tablet PC, try to find the symptoms under the Problem column of the troubleshooting table for the feature giving you difficulty. You will find a description of common causes for that symptom under the column Possible Cause and what, if anything, you can do to correct the condition under Possible Solutions. All possible causes or solutions may not apply to your Tablet PC.
Problem Audio Problems There is no sound coming from the built-in speaker. Possible Cause Possible Solutions The volume is turned too low. Adjust the volume control on your Tablet PC and operating system. Use the [Fn+F9] key combination on your keyboard. Pressing [F9] repeatedly while holding [Fn] will increase the volume of your Tablet PC. The software volume control is set too low. Manually adjusting the volume (i.e.
Problem LifeBook Tablet PC fails to recognize DVD/CDRW/CD-ROM’s. Possible Cause Possible Solutions Optical drive tray is not latched shut. Push on the front of the optical drive tray until it latches. If that doesn’t work, pull out the modular drive latch to remove the device from the bay, then re-insert the drive until it latched; this ensures that the drive is properly seated. Wrong drive designator was used for the disc in the application.
Problem You cannot access your hard drive. (continued) Possible Cause Security is set so your operating system cannot be started without a password. Possible Solutions Verify your password and security settings. Keyboard or Mouse Problems The built-in keyboard does not seem to work. The Tablet PC has gone into Sleep mode. Push the Power/Suspend/Resume button. Your application has locked out your keyboard. Try to use your integrated pointing device to restart your system.
Problem Possible Cause Possible Solutions Your system does not recognize a USB device you have installed, or the device does not seem to work properly. The device may have been installed while an application was running, so your system is not aware of its installation. Close the application and restart your Tablet PC. (continued) Your device may not have the correct software driver active. See your software documentation and activate the correct driver. Card is not properly installed.
Problem You turn on your LifeBook Tablet PC and nothing seems to happen. (continued) Your LifeBook Tablet PC turns off all by itself. Your Tablet PC will not work on battery alone. Possible Cause Possible Solutions The power adapter (AC or auto/airline) is not plugged in properly. Verify that your adapter is connected correctly. See “Power Sources” on page 67. The power adapter (AC or auto/airline) has no power from the AC outlet, airplane jack, or car cigarette lighter.
Problem Possible Cause Possible Solutions Your Tablet PC will not work on battery alone. (continued) Your installed battery is faulty. Verify the condition of the battery using the Status Indicator panel and replace or remove any batteries that are shorted. See “Status Indicator Panel” on page 30. The battery seems to discharge too quickly. The power savings features may be disabled. Check the Power Options menu settings and adjust according to your operating needs.
Problem The system powers up, and displays power on information, but fails to load the operating system. (continued) Possible Cause Possible Solutions The boot sequence settings of the setup utility are not compatible with your configuration. Set the operating source by pressing the [ESC] key while the Fujitsu logo is on screen or use the [F2] key and enter the setup utility and adjust the source settings from the Boot menu. See “BIOS Setup Utility” on page 71. Internal hard drive was not detected.
Problem Possible Cause Possible Solutions The built-in display is blank when you turn on your LifeBook Tablet PC. (continued) The Tablet PC is set for an external monitor only. Pressing [F10] while holding down the [Fn] key allows you to change your selection of where to send your display video. Each time you press the keys you will step to the next choice. The choices, in order are: built-in display only, external monitor only, both built-in display and external monitor.
Problem The display has bright or dark spots. Possible Cause Possible Solutions If the spots are very tiny and few in number, this is normal for a large LCD display. This is normal; do nothing. If the spots are numerous or large enough to interfere with your operation needs. Display is faulty; contact your support representative. The Display is dark when on battery power. The Power Management utility default is set on low brightness to conserve power.
Power On Self Test Messages The following is an alphabetic list of error-and-status messages that Phoenix BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. If an error message is displayed that is not in this list, write it down and check your operating system documentation both on screen and in the manual. If you can find no reference to the message and its meaning is not clear, contact your support representative for assistance.
*Incorrect Drive B type – run SETUP Type of floppy drive B: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to correct the inconsistency. *Invalid NVRAM Data Problem with NVRAM access. In the unlikely case that you see this message you may have some display problems.
*Parity Check 1 nnnn Parity error found in the system bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. This is a potentially data destroying failure. Contact your support representative. *Parity Check 2 nnnn Parity error found in the I/O bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. This is a potentially data-destroying failure.
*System battery is dead – Replace and run SETUP The BIOS CMOS RAM memory hold up battery is dead. This is part of your BIOS and is a board mounted battery which requires a support representative to change. You can continue operating but you will have to use setup utility default values or reconfigure your setup utility every time you turn off your Tablet PC. This battery has an expected life of 2 to 3 years. System BIOS shadowed System BIOS copied to shadow RAM.
Restoring Your Pre-installed Software The location of your applications, drivers, and utilities is determined by the operating system you are running. Microsoft Windows 7 Professional: Please use the information contained in the “Saving and Recovering Your Factory and System Images” booklet that was packed with your system. Microsoft Windows XP Edition: Please use the following instructions.
3 A window will appear containing a list of applications, drivers, and utilities that you can install from the Drivers and Applications CD. THE COMPONENTS LISTED ARE COLOR-CODED IN TERMS OF THEIR INSTALL STATUS. BLUE INDICATES GREEN INDICATES THAT THE COMPONENT NEEDS TO BE INSTALLED SEPARATELY. GREY INDICATES A COMPONENT THAT IS ALREADY INSTALLED; GREY ITEMS CAN BE REINSTALLED, BUT PRIOR TO INSTALLATION YOU WILL RECEIVE A REMINDER THAT THE COMPONENT IS ALREADY INSTALLED.
Methods for accessing the utilities Certain LifeBook models have the Recovery and Utility applets pre-installed. Other systems require that the Recovery and Utility disc be used (or in the event the hard disk has been reformatted). In order to determine the method for accessing the Recovery and Utility applet, perform the following procedures in order. Determining whether Recovery and Utility is pre-loaded 1 2 Turn on or reboot your system. When the Fujitsu logo appears, press [F12] key.
Running Recovery and Utility from the disc • THE USE OF THIS DISC REQUIRES THAT YOU HAVE A DEVICE CAPABLE OF READING CDS ATTACHED TO YOUR SYSTEM. YOU WILL NEED TO ATTACH AN EXTERNAL PLAYER. FOR MORE INFORMATION ON AVAILABLE EXTERNAL DEVICES, VISIT OUR WEB SITE AT: HTTP://SOLUTIONS.US.FUJITSU.COM/. • THIS DISC CAN ONLY BE USED WITH THE SYSTEM WITH WHICH IT WAS PURCHASED.
Utility tab: The Utility tab contains three tools: System Restore, Hard Disk Data Delete and Partition Creation. • System Restore can help fix problems that might be making your computer run slowly or stop responding. System Restore enables you in rolling back the system to an earlier restore point, and does not affect any of your documents, pictures, or other personal data. • The Hard Disk Data Delete utility is used to delete all data on the hard disk and prevent the data from being reused.
Enable Automatic Update Notifications Automatically searches for new updates on a regular basis (approximately every 3 days). Show update history Brings up a screen that displays a history of updates that have been made via the FDU. About Fujitsu Driver Update Displays the FDU version number and copyright information Fujitsu Driver Update Readme Displays the FDU readme.
Chapter 5 Care and Maintenance Caring for your LifeBook Tablet PC If you use your Fujitsu LifeBook Tablet PC carefully, you will increase its life and reliability. This section provides some tips for looking after the Tablet PC and its devices. THE SYSTEM CONTAINS COMPONENTS THAT CAN BE SEVERELY DAMAGED BY ELECTROSTATIC DISCHARGE (ESD).
• • • • • Your LifeBook Tablet PC is a durable but sensitive electronic device. Treat it with respect and care. Make a habit of transporting it in a suitable carrying case. Do not attempt to service the computer yourself. Always follow installation instructions closely. Keep it away from food and beverages. To protect your Tablet PC from damage and to optimize system performance, be sure to keep all air vents unobstructed, clean, and clear of debris.
Cleaning your LifeBook Tablet PC • Always disconnect the power plug. (Pull the plug, not the cord.) • Clean your LifeBook Tablet PC with / a damp, lint-free cloth. Do not use abrasives or solvents. • Use a soft cloth to remove dust from the screen. Never use glass cleaners. • Always shut down the computer, unplug the power adapter, and remove the battery when cleaning or disinfecting the computer exterior, keyboard or LCD display. NOTE: Avoid wetting the thermal suede in all cases.
Cleaning the dust filter Your LifeBook is equipped with fans to make air flow inside by pulling in outside air to cool the inside of the system. Depending on the environment in which the system is used, dust and dirt may be pulled in along with the air. Accumulated dust and dirt could impair the function of the system. • REMOVE AC ADAPTER: BEFORE REMOVING THE FILTER, TURN OFF THE SYSTEM AND PERIPHERALS AND AC ADAPTER.
• Store your Tablet PC and batteries separately. If you store your LifeBook with a battery installed, the battery will discharge, and battery life will be reduced. In addition, a faulty battery might damage your LifeBook. • ALWAYS POWER OFF THE COMPUTER BEFORE TRANSPORTING AND/OR PACKAGING IT. AFTER SHUTTING DOWN LED PANEL INDICATES POWER OFF CONDITION (I.E., NO LIGHTS ARE ILLUMINATED).
• Take the necessary plug adapters if you're traveling overseas. Check the following diagram to determine which plug adapter you'll need or ask your travel agent.
Increasing Battery Life • • • • • • • • Power your Tablet PC through the AC or optional auto/airline adapter whenever possible. If your tablet runs on battery power all day, connect it to an AC adapter overnight to recharge it. Keep brightness to the lowest level comfortable. Set the power management for maximum battery life. Put your Tablet PC in Sleep mode when it is turned on and you are not actually using it. Limit your media drive access. Disable the Media Player auto insert notification function.
Caring for your Optical Drive Your optical drive is durable but you must treat it with care. Please pay attention to the following points: • The drive rotates the compact disc at a very high speed. Do not carry it around or subject it to shock or vibration with the power on. • Avoid using or storing the drive where it will be exposed to extreme temperatures. • Avoid using or storing the drive where it is damp or dusty.
Chapter 6 System Specifications Specifications This section provides the hardware and environmental specifications for your Fujitsu LifeBook Tablet PC. Specifications of particular configurations will vary. Configuration Label The configuration label located on the bottom of your Tablet PC contains specific information regarding the options you’ve chosen for your Tablet PC. Following is an example configuration label.
Microprocessor New 2010 Intel® Core™ Processor (Refer to the system label to determine the speed of your processor). Chipset • Mobile Intel® QM57 Express • Platform Control Hub (PCH) Memory System Memory • DDR3-1066 MHz SDRAM dual-channel memory module. • Two DIMM slots; upgradeable to 8 GB of total memory (4 GB x 2). Cache Memory Up to 4MB L3 cache on-die (depending upon CPU) Video Built-in color flat-panel TFT active matrix LED backlit display with simultaneous display capability.
Digitizer Depending upon the configuration of your system, one of two digitizer options is included: • Active digitizer (uses active stylus input), or, • Dual Digitizer, consisting of active digitizer and capacitive touch panel (uses active stylus input and two finger touch input). Audio • Realtek codec ALC269 with High Definition (HD) audio. • Headphones: Stereo headphone jack, 3.5 mm, 1 Vrms or less, minimum impedance 32 Ohms • Microphone: Stereo microphone jack, 3.
Features Integrated Pointing Device Touchpad cursor control buttons, with scroll strip built-in Communications • Gigabit LAN: Intel 82577LM 10/100/1000 Gigabit Ethernet LAN • WLAN: Optional integrated Intel Centrino Advanced-N 6200 (a/b/g/n, 2 x 2) or Atheros XSPAN 802.11bgn • Bluetooth: Optional Bluetooth V2.1 device for wireless personal area network communication Web Camera Optional built-in 2.0 megapixel web camera.
Device Ports On the LifeBook Tablet PC: • • • • • • Express Card slot for one Express Card Memory Stick/SD Card slot One 15-pin D-SUB connector for VGA external monitor (see Display specifications) Three USB 2.
Keyboard Built-in keyboard with all functions of 101 key PS/2 compatible keyboards. • • • • • • • • Total number of keys: 84 Function keys: F1 through F12, plus Fn extension key Two Windows keys: one Start key, one application key Key pitch: 19 mm; key stroke: 3.0 mm Built-in Touchpad pointing device with two left and two right buttons and scroll strip. Built-in Palm Rest Spill-resistant External USB keyboard/mouse support Power Battery • Standard Lithium ion battery, rechargeable, 6-cell, 10.
Dimensions and Weight Overall Dimensions 11.69"(w) x 9.17"(d) x 1.49”(h) (297 mm x 233 mm x 37.9 mm) Weight Wide-view display, active digitizer with weight saver - 3.92 lbs. (1.78 kg) Wide-view display, active digitizer with optical drive: 4.3 lbs. (1.95 kg) Standard display, dual-digitizer with optical drive: 4.54 lbs. (2.06 kg) Environmental Requirements Temperature Operating: 41° to 95° F (5° to 35° C).
Pre-Installed Software Depending on your pre-installed operating system, your Tablet PC comes with pre-installed software for playing audio and video files of various formats. In addition there is file transfer software and virus protection software. THE FOLLOWING LIST CONSTITUTES THE SOFTWARE THAT MAY BE INSTALLED ON YOUR COMPUTER. THE PRE-INSTALLED SOFTWARE MAY VARY, AND IS DETERMINED BY YOUR OPERATING SYSTEM AND CONFIGURATION.
Learning About Your Software Tutorials All operating systems and most application software have tutorials built into them upon installation. We highly recommend that you step through the tutorial before you use an application. Manuals Included with your Tablet PC you will find manuals for your installed operating system and other preinstalled software. Any manuals that are not included are available online through the software’s “Help” menu.
CyberLink PowerDVD CyberLink PowerDVD allows you to produce and edit home movies and slideshows on discs. CyberLink YouCam CyberLink YouCam allows you to capture photos or movies on the embedded webcam, add special effects to them, and share them in a variety of formats or via social networks. CyberLink PowerDirector CyberLink PowerDirector allows you to edit and enhance your videos, and add special effects to them.
video recordings, and more — all in one digital notebook on your computer. Office OneNote® 2007 can help you become more productive by keeping the information you need at your fingertips and reducing time spent searching for information across e-mail messages, paper notebooks, file folders, and printouts. Microsoft Touch Pack The Microsoft Touch Pack is a set of three applications and three games that let you enjoy the interactive touch screen with the use of gestures and touches.
Glossary AC Adapter A device which converts the AC voltage from a wall outlet to the DC voltage needed to power your LifeBook Tablet PC. Access point Wireless network device used to bridge wireless and wired network traffic. ACPI Advanced Configuration and Power Interface Active-Matrix Display A type of technology for making flat-panel displays which has a transistor or similar device for every pixel on the screen.
ADSL Asymmetric Digital Subscriber Line. Technology for transporting high bit-rate services over ordinary phone lines. AGP Accelerated Graphics Port. Graphics port specifically designed for graphics-intensive devices, such as video cards and 3D accelerators. Auto/Airline Adapter A device which converts the DC voltage from an automobile cigarette lighter or aircraft DC power outlet to the DC voltage needed to power your LifeBook Tablet PC. BIOS Basic Input-Output System.
Bus An electrical circuit which passes data between the CPU and the sub-assemblies inside your LifeBook Tablet PC. Byte 8 bits of parallel binary information. Cache Memory A block of memory built into the micro-processor which is much faster to access than your system RAM and used in specially structured ways to make your overall data handling time faster. CD-ROM Compact disk read only memory. This is a form of digital data storage which is read optically with a laser rather than a magnetic head.
Configuration The combination of hardware and software that makes up your system and how it is allocated for use. CRT Cathode Ray Tube. A display device which uses a beam of electronic particles striking a luminescent screen. It produces a visual image by varying the position and intensity of the beam. Data The information a system stores and processes. DC Direct current. A voltage or current that does not fluctuate periodically with time.
Disk Drive The hardware which spins the disk and has the heads and control circuitry for reading and writing the data on the disk. Diskette A floppy disk in a hard housing with a shutter. DMA Direct Memory Access. Special circuitry for memory to memory transfers of data which do not require CPU action. DMI Desktop Management Interface.
DVMT Dynamic Video Memory Technology. A video memory architecture that increases the efficiency of the motherboard by using innovative memory utilization and direct AGP. ECP Extended Capability Port. A set of standards for high speed data communication and interconnection between electronic devices. Encryption Key (Network Key) Data encryption key used to encrypt message text and for computing message integrity checks. Data encryption protects data from unauthorized viewing.
Hard drive A spinning platter of magnetic data storage media where the platter is very stiff. I/O Input/Output. Data entering and leaving your Tablet PC in electronic form. I/O Port The connector and associated control circuits for data entering and leaving your Tablet PC in electronic form. IDE Intelligent Drive Electronics. A type of control interface for a hard drive which is inside the hard drive unit. IEEE802.11a Wireless LAN standard that supports a maximum data rate of 54 Mbps. 802.
Infrastructure A name of a wireless LAN configuration. This type of communication uses an access point. Another type of communication is called Ad Hoc. IP Address An identifier for a computer or device on a TCP/IP network. Networks using the TCP/IP protocol route messages based on the IP address of the destination. The format of an IP address is a 32-bit numeric address written as four numbers separated by periods. Each number can be zero to 255. For example, 1.160.10.240 could be an IP address.
IRQ Interrupt Request. An acronym for the hardware signal to the CPU that an external event has occurred which needs to be processed. KB Kilobyte. One thousand bytes. LAN Local Area Network. An interconnection of computers and peripherals within a single limited geographic location which can pass programs and data amongst themselves. LCD Liquid Crystal Display. A type of display which makes images by controlling the orientation of crystals in a crystalline liquid.
MB Megabyte. One million bytes. Megahertz 1,000,000 cycles per second. Memory A repository for data and applications which is readily accessible to your LifeBook Tablet PC’s CPU. MHz Megahertz. MIDI Musical Instrument Digital Interface. A standard communication protocol for exchange of information between computers and sound producers such as synthesizers. Modem A contraction for MOdulator-DEModulator. The equipment which connects a computer or other data terminal to a communication line.
Network key Data that is used for encrypting data in data communication. The personal computer uses the same network key both for data encryption and decryption, therefore, it is necessary to set the same network key as the other side of communication. Network name (SSID: Service Set Identifier ) When a wireless LAN network is configured, grouping is performed to avoid interference or data theft. This grouping is performed with “Network name (SSID)”.
Peripheral Device A piece of equipment which performs a specific function associated with but not integral to a computer. Examples: a printer, a modem, a CD-ROM. Pitch (keyboard) The distance between the centers of the letter keys of a keyboard. Pixel The smallest element of a display, a dot of color on your display screen. The more pixels per area the clearer your image will appear. POST Power On Self Test.
Protocol Procedures and rules use to send and receive data between computers. - Method of sending and receiving data - Process used to handle communication errors Conditions required for communication are organized in procedures for correct transfer of information. RAM Random Access Memory. A hardware component of your LifeBook Tablet PC that holds binary information (both program and data) as long as it has the proper power applied to it.
SDRAM Synchronous Dynamic Random Access Memory. Serial Port A connection to another device through which data is transferred one bit at a time on a single wire with any other wires only for control of the device not for transfer of data. Shared key authentication 802.11 network authentication method in which the AP sends the client device a challenge text packet that the client must then encrypt with the correct WEP key and return to the AP.
Stereo (audio) A system using two channels to process sound from two different sources. Subnet mask TCP-IP network is controlled by being divided into multiple smaller networks (subnets). IP address consists of the subnet address and the address of each computer. Subnet mask defines how many bits of IP address comprise the subnet address. The same value shall be set among computers communicating with each other. SVGA Super VGA. S-Video Super Video.
USB Universal Serial Bus. Standard that allows you to simultaneously connect up to 127 USB devices such as game pads, pointing devices, printers, and keyboards to your computer. VRAM Video Random Access Memory. A memory dedicated to video display data and control. WFM Wired for Management is Intel’s broad-based initiative to reduce the total cost of ownership (TCO) of business computing without sacrificing power and flexibility.
Regulatory Information Notice Changes or modifications not expressly approved by Fujitsu could void this user’s authority to operate the equipment. FCC NOTICES Notice to Users of Radios and Television This equipment has been tested and found to comply with the limit for class B digital devices, pursuant to parts 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Appendix A: WLAN User’s Guide FCC Regulatory Information Please note the following regulatory information related to the optional wireless LAN device. Regulatory Notes and Statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions, however, are far much less than the electromagnetic energy emissions from wireless devices such as mobile phones.
Regulatory Information/Disclaimers Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.
FCC Radio Frequency Exposure statement The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used.
Before Using the Optional Wireless LAN This manual describes the procedures required to properly set up and configure the optional integrated Wireless LAN Mini-PCI device (referred to as "WLAN device" in the rest of the manual). Before using the WLAN device, read this manual carefully to ensure its correct operation. Keep this manual in a safe place for future reference.
Wireless LAN Modes Using this Device Ad Hoc Mode "Ad Hoc Mode" refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Point(s). Connectivity is accomplished using only client devices in a peer-to-peer fashion. That is why Ad Hoc networks are also known as peer-to-peer networks.
Access Point (Infrastructure) Mode Infrastructure mode refers to a wireless network architecture in which devices communicate with wireless or wired network devices by communicating through an Access Point. In infrastructure mode, wireless devices can communicate with each other or with a wired network. Corporate wireless networks operate in infrastructure mode because they require access to the WLAN in order to access services, devices, and computers (e.g., file servers, printers, databases).
How to Handle This Device The WLAN device is an optional device that may come pre-installed in your mobile computer. Under normal circumstances, it should not be necessary for you to remove or re-install it. The operating system that your mobile computer comes with has been pre-configured to support the WLAN device. • The Wireless LAN devices support IEEE802.11a, IEEE802.11b, IEEE802.11g, and IEEE802.11n. • The WLAN devices operate in the 2.4 GHz ISM band and the 5 GHz lower, middle, and upper UNII bands.
Deactivation Using the Wireless On/Off Switch The WLAN device can be deactivated quickly and efficiently by toggling the Wireless LAN/Bluetooth On/Off Switch to the Off position. The switch has no effect on non-Wireless LAN models. WLAN/Bluetooth Switch Figure 50. Wireless LAN/Bluetooth On/Off Switch Location Disconnection Using the Icon in the Taskbar Note that disconnecting via the icon in the system tray does not turn off the radio; it continues to transmit and receive even though it’s not connected.
Configuring the Wireless LAN The WLAN device can be configured to establish wireless network connectivity using the software that is built into Windows. Support for most industry standard security solutions is contained in this software. Pre-defined parameters will be required for this procedure. Please consult with your network administrator for these parameters: Configuring the WLAN 1 2 Click the Start button, then select Control Panel. 3 4 5 6 7 8 Double-click on the Wireless Network Connection icon.
Troubleshooting the WLAN Troubleshooting Causes and countermeasures for troubles you may encounter while using your wireless LAN are described in the following table.
Problem Unavailable network connection (continued) Possible Cause Possible Solution RF interference from Access Points or other wireless networks The use of identical or overlapping RF channels can cause interference with the operation of the WLAN device. Change the channel of your Access Point to a channel that does not overlap with the interfering device. Wireless network authentication has failed Re-check your Network Authentication, Encryption, and Security settings.
WLAN Specifications Specifications Item Specification Type of network The optional integrated Intel Centrino Advanced-N 6200 (a/b/g/n, 2 x 2) and Atheros XSPAN 802.11bgn) WLAN devices conform to IEEE 802.11a, 802.11b/g, and 802.11n (draft-compliant), Wi-Fi based*. Transfer rate (Automatic switching) 54 Mbps maximum data rate (IEEE802.11n to be determined) Active frequency • • • 802.11n (draft): 2.4 GHz or 5 GHz 802.11b/g: 2400~2473 MHz 802.
* “Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the interconnectivity of wireless LAN (Wi-Fi Alliance) has been passed. ** The communication ranges shown above will increase or decrease depending on factors such as number of walls, reflective material, or interference from external RF sources. *** Encryption with network key (WEP) is performed using the above number of bits, however, users can set 40 bits/ 104 bits after subtracting the fixed length of 24 bits.
Using the Bluetooth Device The optional Integrated Bluetooth module (BSMAN3) is a wireless device installed in selected Fujitsu mobile computers. What is Bluetooth Bluetooth technology is designed as a short-range wireless link between mobile devices, such as laptop computers, phones, printers, and cameras. Bluetooth technology is used to create Personal Area Networks (PANs) between devices in short-range of each other.
FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The Bluetooth antenna is located on the front edge of the right palm rest and is exempt from minimum distance criteria due to its low power. The transmitters in this device must not be co-located or operated in conjunction with any other antenna or transmitter.
Appendix B: Fingerprint Sensor Device Introducing the Fingerprint Sensor Device Your system has a fingerprint sensor device at the bottom left below the display screen. Fingerprint Sensor Device Figure 51.
• Log into homepages that require a username and password After you have “enrolled” - or registered - your fingerprint, you can simply swipe your fingertip over the sensor for the system recognize you. The fingerprint sensor uses Softex OmniPass which provides password management capabilities to Microsoft Windows operating systems. OmniPass enables you to use a "master password" for all Windows, applications, and on-line passwords.
• Windows XP Professional operating system • At least 35 MB available hard disk space Installing the OmniPass Application If OmniPass is already installed on your system, go to “User Enrollment” on page 181. Otherwise continue with this section on software installation. • • INSTALLATION OF THE APPLICATION REQUIRES THAT YOU HAVE AN EXTERNAL OPTICAL DRIVE ATTACHED TO YOUR SYSTEM. FOR INSTALLATION, OMNIPASS REQUIRES THAT THE USER INSTALLING OMNIPASS HAVE ADMINISTRATIVE PRIVILEGES TO THE SYSTEM.
1 From the Windows Desktop, double-click the key-shaped OmniPass icon in the taskbar (usually located in the lower right corner of the screen), or, Click the Start button, select Settings, and click Control Panel. Double-click Softex OmniPass in the Control Panel, and the OmniPass Control Center will appear.
User Enrollment Before you can use any OmniPass features you must first enroll a user into OmniPass. Master Password Concept Computer resources are often protected with passwords. Whether you are logging into your computer, accessing your email, e-banking, paying bills online, or accessing network resources, you often have to supply credentials to gain access. This can result in dozens of sets of credentials that you have to remember.
Basic Enrollment The Enrollment Wizard will guide you through the process of enrolling a user. Unless you specified otherwise, after OmniPass installation the Enrollment Wizard will launch on Windows login. If you do not see the Enrollment Wizard, you can bring it up by clicking Start on the Windows taskbar; select Programs; select Softex; click OmniPass Enrollment Wizard. 1 Click Enroll to proceed to username and password verification.
1 During initial user enrollment, you will be prompted to select the finger you wish to enroll. Fingers that have already been enrolled will be marked by a green check. The finger you select to enroll at this time will be marked by a red arrow. OmniPass will allow you re-enroll a finger. If you choose a finger that has already been enrolled and continue enrollment, OmniPass will enroll the fingerprint, overwriting the old fingerprint. Select a finger to enroll and click [Next].
OmniPass Authentication Toolbar After installing OmniPass and restarting, you will notice a dialog you have not seen before at Windows Logon. This is the OmniPass Authentication Toolbar, and it is displayed whenever the OmniPass authentication system is invoked.
Associating a Friendly Name After clicking the OmniPass key cursor near the login prompt, OmniPass will prompt you to enter a “friendly name” for this site. You should enter something that reminds you of the website, the company, or the service you are logging into. In its secure database, OmniPass associates this friendly name with this website.
Click Finish to complete the remember password procedure. The site location, the credentials to access the site, and the OmniPass authentication settings for the site are now stored in the OmniPass secure database. The OmniPass authentication settings (Settings for this Password Site) can always be changed in Vault Management.
Password Management OmniPass provides an interface that lets you manage your passwords. To access this GUI, double-click the OmniPass key in the system tray. Click Vault Management; you will be prompted to authenticate. Once you gain access to Vault Management, click Manage Passwords under Vault Settings. You will see the Manage Passwords interface, with a list of friendly names.
To add a new identity, click New Identity or double-click Click here to add a new identity. Name the new identity and click [OK], then click [Apply]. You can now switch to the new identity and start remembering passwords. To delete an identity, highlight the identity you want to delete and click [Delete Identity], then [Apply]. WHEN YOU DELETE AN IDENTITY, ALL OF ITS ASSOCIATED REMEMBERED SITES AND PASSWORD PROTECTED DIALOGS ARE LOST.
Configuring OmniPass This section gives an overview of both the Export/Import function and the OmniPass Control Center. Exporting and Importing Users YOU CANNOT IMPORT A USER INTO OMNIPASS IF THERE ALREADY IS A USER WITH THE SAME NAME OMNIPASS. ENROLLED IN Using OmniPass Control Center, you can export and import users in and out of OmniPass. The export process backs up all remembered sites, credentials, and enrolled fingerprints for an OmniPass user.
This .opi file contains all your user specific OmniPass data, and it is both encrypted and password protected. This user profile does NOT contain any of your encrypted data files. Importing an OmniPass User Profile To import an OmniPass user open the OmniPass Control Center, and click Import/Export User under Manage Users. Click Imports a new user into OmniPass and then select OmniPass Import/Export File (*.opi) and click Next.
OmniPass Control Center This section will serve to explain functions within the OmniPass Control Center that weren’t explained earlier. You can access the OmniPass Control Center any of three ways: • Double-click the golden OmniPass key shaped icon in the Windows taskbar (typically in the lowerright corner of the desktop) • Click the Start button; select the Programs group; select the Softex program group; and click the OmniPass Control Center selection.
User Settings The User Settings tab has four interfaces: Audio Settings, Taskbar Tips, and Enrollment. User settings allow users to customize OmniPass to suit their individual preferences. Under User Settings (Audio Settings and Taskbar Tips) you can set how OmniPass notifies the user of OmniPass events (e.g., successful login, access denied, etc.). The details of each setting under the Audio Settings and Taskbar Tips interfaces are self-explanatory.
Troubleshooting You cannot use OmniPass to create Windows users. You must first create the Windows user, and you will need administrative privileges to do that. Once the Windows user is created, you can add that user to OmniPass using the same username and password Cannot add Windows users to OmniPass If you experience difficulties adding a Windows user to OmniPass, you may need to adjust your local security settings.
If you are having difficulties due to the first reason, you will need to update OmniPass with your changed Windows account password. Click Update Password and you will be prompted with a dialog to reconfirm your password. Enter the new password to your Windows user account and click OK. If the error persists, then it is unlikely the problem is due to your Windows user account password changing.
Index Battery Latches 29 BIOS guide 73 setup utility 72 Bluetooth Where to Find Information 177 Boot Sequence 71 Booting the System 73 Built-in Speakers 108 Button Icons 57, 60 A About This Guide 13 AC adapter 68 indicator 31 plug adapters 132 Active Digitizer 47 Air Vents 27, 29 Anti-theft lock slot 26 Auto/Airline Adapter 68, 69 Automatically Downloading Driver Updates 125 C CapsLock 32 CD-ROM 108, 109 Click Me! 75 Cold-swapping 55 Configuration Label 135 Contact Information 14 Controls and Connectors 1
Display Panel 20, 33 brightness 37 opening 33 problems 114, 115 Dock port 17 Docking Port 100 Double-Clicking 43 Dragging 43, 45 Drivers and Application Restore CD 121 Dual Built-in Microphones 22 DVD drive problems 108, 109 password replacement 185 remembering a password 186 uninstalling OmniPass 182 user enrollment 183 using OmniPass 185 Fujitsu Contact Information 14 Fujitsu Driver Update utility 76, 125, 144 Fujitsu LifeBook storing 130 traveling 131 Fujitsu Shopping Online 15 Function Key F10 41 F3 41
capacity 93 checking capacity 93 compartment 28, 91 installing 91 problems 110 upgrade module 91 Memory Stick installing 88 removing 88 Memory Stick/Secure Digital Cards 87 Microphone Jack 17, 23, 103 Modular Bay 54 cold-swapping 55 devices 54 installing 55 removing 55 Modular Devices 55 installing 55 removing 55 Mouse problems 110 I IEEE 1394 (4-pin) Jack 21 IEEE 1394 Port 101 Internal LAN Jack 100 K Keyboard 21, 39 cursor keys 39 function keys 40 numeric keypad 39 problems 110 windows keys 40 L LifeBoo
Pen Tether Attachment Point 25 Port Replicator connector 29 problems 109 Post-logon button functions 59 Power AC adapter 68 Auto/Airline adapter 68 failure 111, 112 indicator 30 management 77 off 80 on 70 problems 113 sources 68 Power Management 77 Power On Self Test 71, 117 Power/Suspend/Resume Button 20, 77 Pre-Installed Software 142 Adobe Acrobat Reader 143 Google Toolbar 143, 144 manuals 143 Pre-logon button functions 57 SD/Memory Stick Slot 17 SDRAM 28, 91 Secure Digital Card removing 88 Security Butt
U Universal Serial Bus Ports 101 USB 101, 110 USB 2.
