User Manual
Table Of Contents
- FUJITSU LIFEBOOK E5412 | E5512
- Contents
- Innovative technology
- Ports and controls
- Important notes
- First-time setup of your device
- Working with the notebook
- Status indicators
- Switching on the notebook
- Switching off the notebook
- Keyboard
- Touchpad and touchpad buttons
- Touchscreen/LCD screen without touch function (device-dependent)
- WebCam and Infrared Camera
- Rechargeable battery
- Using the power-management features
- Memory cards
- Loudspeakers and microphones
- SIM card (configuration dependent)
- Wireless components Wireless LAN€/ Bluetooth€/ LTE (optional)
- Ethernet and LAN
- Your Port Replicator
- Security functions
- Connecting external devices
- Removing and installing components during servicing
- Settings in BIOS Setup Utility
- Starting the BIOS Setup Utility
- Operating the BIOS Setup Utility
- Exiting BIOS Setup Utility
- Exit Saving Changes - save changes and exit BIOS Setup Utility
- Exit Discarding Changes – Discard changes and exit BIOS Setup Utility
- Load Setup Defaults – Copy Standard Entries
- Discard Changes – Discard changes without exiting the BIOS Setup Utility
- Save Changes - save changes without exiting the BIOS Setup Utility
- Save Changes and Power Off
- Erase Disk
- Troubleshooting and tips
- Help if problems occur
- Recovering drive contents from the Recovery DVD
- Restoring the system under Windows
- The notebook's date or time is incorrect
- When certain characters are entered on the keyboard, only numerals are written
- The notebook’s LCD screen remains blank
- The LCD screen is difficult to read
- The external monitor remains blank
- The external monitor is blank or the image is unstable
- The notebook cannot be started
- The notebook stops working
- The printer does not print
- The wireless connection to a network does not work
- SmartCard reader is not recognised.
- SmartCard PIN forgotten
- SmartCard lost
- Error messages on the screen
- Technical data
- Manufacturer’s notes
- Index
Troubleshooting and tips
Error messages on the screen
Errormessages onthescr eenErrormessage:
This section describes the error messages generated by the BIOS Setup. Error messages displayed
by the operating system or programme s are described in the relevant documentation.
If the error message appears repeatedly, despite troubleshooting m easure s, please
contact the place of purchase or o ur customer service centre.
Error message/cause Resolution
CMOS ba ttery bad
If the error message occurs repeatedly, the
buffer battery in the notebook is flat.
► Contact your sales outlet
or our customer
service centre.
System CMOS checksum bad - Default configuration
used
The system configuration inform ation is
incorrect.
► Switch the notebook of
f.
► Switch the notebook on.
► Press the function k
ey
F2
to access the
BIOS Setup.
► In the BIOS Setup, select the Exit menu.
► Select the entry Lo
ad Setup Defaults.
► Select OK and press the Enter key.
Extended memory failed at offset: xxxx Failing B its:
zzzz zzzz
When testing th e extended memory an error has
resulted at the address xxxx.
► Check whether the additional memory
module has been inserted correctly.
Failure Fixed Disk n
The drive settings are incorrect.
► Start the BIOS Setup (P ri mary Master
submenu) and select the correct settings.
Keyboard controller error
► Switch the notebook off using with the
ON/OFF button.
► Wait 3 - 5 seconds and switch on the
notebook aga in.
Keyboard error
If you are using an external keybo ard:
► Check the connection and reboot the
notebook.
nn Stuck key
► Make sure that no key is pressed.
Operating system not found
► Check
whether your drive has been correctly
config
ured in the BIOS Setup.
► Make sure that the operating system is
installed on the corresponding drive.
Press <F1> to resume, < F2> to SE TU P
This error message appears if an error occurs
during the self-test before starting the operating
system.
► Press the
F1
function key to start the
operating system.
► Press the function key
F2
to access the
BIOS Setup.
74 Fujitsu