Design Technical Manual
Table Of Contents
- CHAPTER00
- CHAPTER01_General_information
- CHAPTER02_Model_selection
- 1. MODEL SELECTION PROCEDURE
- 2. MODEL LINE UP
- 3. MODEL SELECTION AND CAPACITY CALCULATION
- 4. CAPACITY TABLE COOLING (OUTDOOR UNIT)
- 5. CAPACITY TABLE HEATING (OUTDOOR UNIT)
- 6. CAPACITY COMPENSATION COEFFICIENT
- 7. CAPACITY TABLE COOLING (INDOOR UNIT)
- 7-1. COMPACT CASSETTE TYPE
- 7-2. CIRCULAR FLOW CASSETTE TYPE
- 7-3. CASSETTE TYPE
- 7-4. MINI DUCT TYPE
- 7-5. SLIM DUCT / SLIM CONCEALED FLOOR TYPE
- 7-6. MEDIUM STATIC PRESSURE DUCT TYPE
- 7-7. HIGH STATIC PRESSURE DUCT TYPE
- 7-8. VERTICAL AIR HANDLER TYPE
- 7-9. COMPACT FLOOR TYPE
- 7-10. FLOOR / CEILING TYPE
- 7-11. CEILING TYPE
- 7-12. WALL MOUNTED TYPE
- 8. CAPACITY TABLE HEATING (INDOOR UNIT)
- 8-1. COMPACT CASSETTE TYPE
- 8-2. CIRCULAR FLOW CASSETTE TYPE
- 8-3. CASSETTE TYPE
- 8-4. MINI DUCT TYPE
- 8-5. SLIM DUCT / SLIM CONCEALED FLOOR TYPE
- 8-6. MEDIUM STATIC PRESSURE DUCT TYPE
- 8-7. HIGH STATIC PRESSURE DUCT TYPE
- 8-8. VERTICAL AIR HANDLER TYPE
- 8-9. COMPACT FLOOR TYPE
- 8-10. FLOOR / CEILING TYPE
- 8-11. CEILING TYPE
- 8-12. WALL MOUNTED TYPE
- CHAPTER03_Outdoor_units
- CHAPTER04_Indoor_units
- CHAPTER05_Control_system
- 1. CONTROL SYSTEM
- 2. CONTROL UNITS
- 2-1. SYSTEM CONTROLLER
- 2-2. SYSTEM CONTROLLER LITE
- 2-3. TOUCH PANEL CONTROLLER
- 2-4. CENTRAL REMOTE CONTROLLER
- 2-5. WIRED REMOTE CONTROLLER (Touch panel)
- 2-6. WIRED REMOTE CONTROLLER
- 2-7. SIMPLE REMOTE CONTROLLER (With Operation mode)
- 2-8. SIMPLE REMOTE CONTROLLER (Without Operation mode)
- 2-9. WIRELESS REMOTE CONTROLLER
- 2-10. IR RECEIVER UNIT (for ALL DUCT TYPE)
- 2-11. IR RECEIVER UNIT (for CASSETTE TYPE)
- 2-12. IR RECEIVER UNIT (for CIRCULAR FLOW CASSETTE TYPE)
- 2-13. HUMAN SENSOR KIT (for CIRCULAR FLOW CASSETTE TYPE)
- 2-14. REMOTE SENSOR UNIT
- 2-15. PRESSURE SENSOR KIT
- 2-16. GROUP CONTROL METHOD
- 2-17. COMPARISON TABLE OF CONTROLLERS
- 3. ADAPTOR / CONVERTOR UNITS
- 4. SERVICE & WEB MONITORING TOOL
- CHAPTER06_System_design
- CHAPTER07_Function_setting
- CHAPTER08_External_input_and_output
- CHAPTER09_Notes
- CHAPTER10_Optional_parts
- CHAPTER99
LED105
CODE No.
Setting Mode
LED104
CODE No.
Setting Function
Factory
setting
Outdoor unit
Remarks
Master Slave
2 0
Switching
between
batch stop or
emergency stop
0 0 Batch stop
l
¡
-
*1
This mode selects the pattern of
the stop function to be operated
by the external input terminal
(CN134).
•Batch stop: The stop of all
indoor units connected to same
refrigerant system due to input
signal coming from CN134.
•Emergency stop: When
emergency stop is actuated, the
indoor unit does not accept the
operation command from the
remote controller. On the other
hand, when the emergency
stop is released (no input from
CN134), the air conditioner
does not return to the original
operation until operate indoor
unit by the remote controller.
0 1 Emergency stop
2 2
Snow falling
protection fan
mode
0 0 Enable
l
¡
-
*1
This mode operates the fans
of outdoor units in order to
prevent the units from stopping
operation when they are
covered by snow.
0 1 Disable
2 3
Interval setting
for snow falling
protection fan
mode
0 0 Standard (30minutes)
l
¡
-
*1
When the snow falling protection
fan mode is set, the operation
interval of the fans of outdoor
units can be selected.
0 1 Short1 (5minutes)
0 2 Short2 (10minutes)
0 3 Short3 (20minutes)
2 4
High static
pressure mode
0 0 Standard
l
¡ ¡
When installing a duct to the
discharge of an outdoor unit, set
the high static pressure mode
according to the static pressure
of the duct to be installed.
Furthermore, use this setting if
the Airow from the discharge
of an outdoor unit is poor, such
as when installed in a place with
a low ceiling.
0 1
High static pressure 1
(equivalent to 30Pa)
0 2
High static pressure 2
(equivalent to maximum)
0 3 Prohibited
2 5 Prohibited
0 0 Prohibited
l
Setting prohibited
0 1 Prohibited
2 6 Prohibited
0 0 Prohibited
l
Setting prohibited
0 1 Prohibited
2 7 Prohibited
0 0 Prohibited
l
Setting prohibited
0 1 Prohibited
2 8
Change of unit
(Temperature)
0 0 Celsius (°C)
l
¡ ¡
0 1 Fahrenheit (°F)
2 9
Change of unit
(Pressure)
0 0 MPa
l
¡ ¡
0 1 psi
*1: Do not set this for outdoor units with Slave setting.
- (07 - 62) -
FUNCTION
SETTING
FUNCTION
SETTING