Design Technical Manual
Table Of Contents
- CHAPTER00
- CHAPTER01_General_information
- CHAPTER02_Model_selection
- 1. MODEL SELECTION PROCEDURE
- 2. MODEL LINE UP
- 3. MODEL SELECTION AND CAPACITY CALCULATION
- 4. CAPACITY TABLE COOLING (OUTDOOR UNIT)
- 5. CAPACITY TABLE HEATING (OUTDOOR UNIT)
- 6. CAPACITY COMPENSATION COEFFICIENT
- 7. CAPACITY TABLE COOLING (INDOOR UNIT)
- 7-1. COMPACT CASSETTE TYPE
- 7-2. CIRCULAR FLOW CASSETTE TYPE
- 7-3. CASSETTE TYPE
- 7-4. MINI DUCT TYPE
- 7-5. SLIM DUCT / SLIM CONCEALED FLOOR TYPE
- 7-6. MEDIUM STATIC PRESSURE DUCT TYPE
- 7-7. HIGH STATIC PRESSURE DUCT TYPE
- 7-8. VERTICAL AIR HANDLER TYPE
- 7-9. COMPACT FLOOR TYPE
- 7-10. FLOOR / CEILING TYPE
- 7-11. CEILING TYPE
- 7-12. WALL MOUNTED TYPE
- 8. CAPACITY TABLE HEATING (INDOOR UNIT)
- 8-1. COMPACT CASSETTE TYPE
- 8-2. CIRCULAR FLOW CASSETTE TYPE
- 8-3. CASSETTE TYPE
- 8-4. MINI DUCT TYPE
- 8-5. SLIM DUCT / SLIM CONCEALED FLOOR TYPE
- 8-6. MEDIUM STATIC PRESSURE DUCT TYPE
- 8-7. HIGH STATIC PRESSURE DUCT TYPE
- 8-8. VERTICAL AIR HANDLER TYPE
- 8-9. COMPACT FLOOR TYPE
- 8-10. FLOOR / CEILING TYPE
- 8-11. CEILING TYPE
- 8-12. WALL MOUNTED TYPE
- CHAPTER03_Outdoor_units
- CHAPTER04_Indoor_units
- CHAPTER05_Control_system
- 1. CONTROL SYSTEM
- 2. CONTROL UNITS
- 2-1. SYSTEM CONTROLLER
- 2-2. SYSTEM CONTROLLER LITE
- 2-3. TOUCH PANEL CONTROLLER
- 2-4. CENTRAL REMOTE CONTROLLER
- 2-5. WIRED REMOTE CONTROLLER (Touch panel)
- 2-6. WIRED REMOTE CONTROLLER
- 2-7. SIMPLE REMOTE CONTROLLER (With Operation mode)
- 2-8. SIMPLE REMOTE CONTROLLER (Without Operation mode)
- 2-9. WIRELESS REMOTE CONTROLLER
- 2-10. IR RECEIVER UNIT (for ALL DUCT TYPE)
- 2-11. IR RECEIVER UNIT (for CASSETTE TYPE)
- 2-12. IR RECEIVER UNIT (for CIRCULAR FLOW CASSETTE TYPE)
- 2-13. HUMAN SENSOR KIT (for CIRCULAR FLOW CASSETTE TYPE)
- 2-14. REMOTE SENSOR UNIT
- 2-15. PRESSURE SENSOR KIT
- 2-16. GROUP CONTROL METHOD
- 2-17. COMPARISON TABLE OF CONTROLLERS
- 3. ADAPTOR / CONVERTOR UNITS
- 4. SERVICE & WEB MONITORING TOOL
- CHAPTER06_System_design
- CHAPTER07_Function_setting
- CHAPTER08_External_input_and_output
- CHAPTER09_Notes
- CHAPTER10_Optional_parts
- CHAPTER99
RB unit
IN/U OUT/U
Signal amplifier
TRANSMISSION TRANSMISSION
RB unit
IN/U OUT/U
RB unit
IN/U OUT/U
Outdoor unit (Master unit)
Outdoor unit (Slave unit) Outdoor unit (Slave unit)
Refrigerant system 1 (Heat Recovery type)
RB group 1
Indoor unit
Indoor unit
Indoor unit
Indoor unit
Indoor unit
Indoor unit
RB group 2RB group 30
RB unit
IN/U OUT/U
RB unit
IN/U OUT/U
Outdoor unit (Master unit)
Outdoor unit (Slave unit)
Refrigerant system 2 (Heat Recovery type)
RB group 31
Indoor unit
Indoor unit
Indoor unit
Indoor unit
RB group 55
Outdoor unit (Master unit)
Refrigerant system n-1 (Heat Pump type)
Indoor unitIndoor unit
Signal amplifier
TRANSMISSION TRANSMISSION
Outdoor unit (Master unit)
Refrigerant system n (Heat Pump type)
Indoor unitIndoor unit
Signal amplifier
TRANSMISSION TRANSMISSION
Step 4
Step 4
Step 4
Step 2
Step 2
Step 2
●
X1, X2 : Indoor unit to outdoor unit (Master)
Indoor unit to RB unit
RB unit to Outdoor unit (Master)
●
Z1, Z2 : Connection for dierent refrigerant circuit of master outdoor unit
●
H1, H2 : Module link connection between master and slave outdoor units
(It is required for combination use.)
Caution: In Step 2 and Step 4 above, transmission line will connect to dierent terminals on
the Signal Amplier.
- (06 - 122) -
SYSTEM
DESIGN
SYSTEM
DESIGN