Design Technical Manual
Table Of Contents
- CHAPTER00
- CHAPTER01_General_information
- CHAPTER02_Model_selection
- 1. MODEL SELECTION PROCEDURE
- 2. MODEL LINE UP
- 3. MODEL SELECTION AND CAPACITY CALCULATION
- 4. CAPACITY TABLE COOLING (OUTDOOR UNIT)
- 5. CAPACITY TABLE HEATING (OUTDOOR UNIT)
- 6. CAPACITY COMPENSATION COEFFICIENT
- 7. CAPACITY TABLE COOLING (INDOOR UNIT)
- 7-1. COMPACT CASSETTE TYPE
- 7-2. CIRCULAR FLOW CASSETTE TYPE
- 7-3. CASSETTE TYPE
- 7-4. MINI DUCT TYPE
- 7-5. SLIM DUCT / SLIM CONCEALED FLOOR TYPE
- 7-6. MEDIUM STATIC PRESSURE DUCT TYPE
- 7-7. HIGH STATIC PRESSURE DUCT TYPE
- 7-8. VERTICAL AIR HANDLER TYPE
- 7-9. COMPACT FLOOR TYPE
- 7-10. FLOOR / CEILING TYPE
- 7-11. CEILING TYPE
- 7-12. WALL MOUNTED TYPE
- 8. CAPACITY TABLE HEATING (INDOOR UNIT)
- 8-1. COMPACT CASSETTE TYPE
- 8-2. CIRCULAR FLOW CASSETTE TYPE
- 8-3. CASSETTE TYPE
- 8-4. MINI DUCT TYPE
- 8-5. SLIM DUCT / SLIM CONCEALED FLOOR TYPE
- 8-6. MEDIUM STATIC PRESSURE DUCT TYPE
- 8-7. HIGH STATIC PRESSURE DUCT TYPE
- 8-8. VERTICAL AIR HANDLER TYPE
- 8-9. COMPACT FLOOR TYPE
- 8-10. FLOOR / CEILING TYPE
- 8-11. CEILING TYPE
- 8-12. WALL MOUNTED TYPE
- CHAPTER03_Outdoor_units
- CHAPTER04_Indoor_units
- CHAPTER05_Control_system
- 1. CONTROL SYSTEM
- 2. CONTROL UNITS
- 2-1. SYSTEM CONTROLLER
- 2-2. SYSTEM CONTROLLER LITE
- 2-3. TOUCH PANEL CONTROLLER
- 2-4. CENTRAL REMOTE CONTROLLER
- 2-5. WIRED REMOTE CONTROLLER (Touch panel)
- 2-6. WIRED REMOTE CONTROLLER
- 2-7. SIMPLE REMOTE CONTROLLER (With Operation mode)
- 2-8. SIMPLE REMOTE CONTROLLER (Without Operation mode)
- 2-9. WIRELESS REMOTE CONTROLLER
- 2-10. IR RECEIVER UNIT (for ALL DUCT TYPE)
- 2-11. IR RECEIVER UNIT (for CASSETTE TYPE)
- 2-12. IR RECEIVER UNIT (for CIRCULAR FLOW CASSETTE TYPE)
- 2-13. HUMAN SENSOR KIT (for CIRCULAR FLOW CASSETTE TYPE)
- 2-14. REMOTE SENSOR UNIT
- 2-15. PRESSURE SENSOR KIT
- 2-16. GROUP CONTROL METHOD
- 2-17. COMPARISON TABLE OF CONTROLLERS
- 3. ADAPTOR / CONVERTOR UNITS
- 4. SERVICE & WEB MONITORING TOOL
- CHAPTER06_System_design
- CHAPTER07_Function_setting
- CHAPTER08_External_input_and_output
- CHAPTER09_Notes
- CHAPTER10_Optional_parts
- CHAPTER99
IN THE CASE OF SET UP THE INDOOR UNIT IN BOTH THE UPPER
SIDE AND THE LOWER SIDE OF THE OUTDOOR UNIT
c
d
e
f
b
a
H
2
H
3
H
5
H
5
H
4
H
5
*4
Limitation:
ft. (m)
Diagram
Maximum allowable pipe
length (actual pipe length)
Between master outdoor unit and the farthest indoor
unit
541 (165) or less a + b + c
Between the rst separation tube and the farthest
indoor unit
197 (60) or less a
Total pipe length 3280 (1000) or less *1 Total
Between outdoor unit and outdoor unit branch kit 9 (3) or less c, d, e
Between the farthest outdoor unit to the rst outdoor
unit branch kit
39 (12) or less d + f, e + f
Maximum allowable
height dierence
Between indoor unit 49 (15) or less H2
Between outdoor unit 19-11/16in. (0.5) or less H3
Between RB unit 49 (15) or less H4
Between RB unit and indoor unit 16 (5) or less H5
¾
1 : Total pipe length is limited by the condition that total refrigerant amount should not exceed 231lbs. (105kg).
¾
3 : When cooling operation will be conducted at outdoor air temperature below 23°F (-5°C) ,the outdoor unit must be installed in a position
that is higher than indoor units or same level as indoor unit or 16’ (5m) lower than indoor unit.
¾
4 : Although "b" does not have limitation. Set to be 541’ (165m) or less in total pipe length of "a+b+c".
¾
5 : The pipe length is 25’ (7.5m) or more, between master outdoor unit and the nearest indoor unit.
- (06 - 37) -
SYSTEM
DESIGN
SYSTEM
DESIGN