Design Technical Manual
Table Of Contents
- CHAPTER00
- CHAPTER01_General_information
- CHAPTER02_Model_selection
- 1. MODEL SELECTION PROCEDURE
- 2. MODEL LINE UP
- 3. MODEL SELECTION AND CAPACITY CALCULATION
- 4. CAPACITY TABLE COOLING (OUTDOOR UNIT)
- 5. CAPACITY TABLE HEATING (OUTDOOR UNIT)
- 6. CAPACITY COMPENSATION COEFFICIENT
- 7. CAPACITY TABLE COOLING (INDOOR UNIT)
- 7-1. COMPACT CASSETTE TYPE
- 7-2. CIRCULAR FLOW CASSETTE TYPE
- 7-3. CASSETTE TYPE
- 7-4. MINI DUCT TYPE
- 7-5. SLIM DUCT / SLIM CONCEALED FLOOR TYPE
- 7-6. MEDIUM STATIC PRESSURE DUCT TYPE
- 7-7. HIGH STATIC PRESSURE DUCT TYPE
- 7-8. VERTICAL AIR HANDLER TYPE
- 7-9. COMPACT FLOOR TYPE
- 7-10. FLOOR / CEILING TYPE
- 7-11. CEILING TYPE
- 7-12. WALL MOUNTED TYPE
- 8. CAPACITY TABLE HEATING (INDOOR UNIT)
- 8-1. COMPACT CASSETTE TYPE
- 8-2. CIRCULAR FLOW CASSETTE TYPE
- 8-3. CASSETTE TYPE
- 8-4. MINI DUCT TYPE
- 8-5. SLIM DUCT / SLIM CONCEALED FLOOR TYPE
- 8-6. MEDIUM STATIC PRESSURE DUCT TYPE
- 8-7. HIGH STATIC PRESSURE DUCT TYPE
- 8-8. VERTICAL AIR HANDLER TYPE
- 8-9. COMPACT FLOOR TYPE
- 8-10. FLOOR / CEILING TYPE
- 8-11. CEILING TYPE
- 8-12. WALL MOUNTED TYPE
- CHAPTER03_Outdoor_units
- CHAPTER04_Indoor_units
- CHAPTER05_Control_system
- 1. CONTROL SYSTEM
- 2. CONTROL UNITS
- 2-1. SYSTEM CONTROLLER
- 2-2. SYSTEM CONTROLLER LITE
- 2-3. TOUCH PANEL CONTROLLER
- 2-4. CENTRAL REMOTE CONTROLLER
- 2-5. WIRED REMOTE CONTROLLER (Touch panel)
- 2-6. WIRED REMOTE CONTROLLER
- 2-7. SIMPLE REMOTE CONTROLLER (With Operation mode)
- 2-8. SIMPLE REMOTE CONTROLLER (Without Operation mode)
- 2-9. WIRELESS REMOTE CONTROLLER
- 2-10. IR RECEIVER UNIT (for ALL DUCT TYPE)
- 2-11. IR RECEIVER UNIT (for CASSETTE TYPE)
- 2-12. IR RECEIVER UNIT (for CIRCULAR FLOW CASSETTE TYPE)
- 2-13. HUMAN SENSOR KIT (for CIRCULAR FLOW CASSETTE TYPE)
- 2-14. REMOTE SENSOR UNIT
- 2-15. PRESSURE SENSOR KIT
- 2-16. GROUP CONTROL METHOD
- 2-17. COMPARISON TABLE OF CONTROLLERS
- 3. ADAPTOR / CONVERTOR UNITS
- 4. SERVICE & WEB MONITORING TOOL
- CHAPTER06_System_design
- CHAPTER07_Function_setting
- CHAPTER08_External_input_and_output
- CHAPTER09_Notes
- CHAPTER10_Optional_parts
- CHAPTER99
z
Installation method
Refer to an installation manual for the details.
Transmission
cable
Transmission
cable
Power supply cable
Power supply
cable
Washer
Harness
Connection cable
Rear view
LAN cable
Cable tie
Touch pen tray
Switch box
Hole in wall
Installation plate
Screw
Screw
(a) Lan cable
(b) Lan terminal
(c) CF card
(a) (b) (c)
Transmission
cable
Transmission
cable
power supply cable
power supply
cable
Washer
Cable tie
Harness
Connection cable
Cable tie
Touch pen tray
Switch box
Hole in wall
Installation plate
Screw
Screw
Case of UTY-DTGYZ1
Case of UTY-DTGY
CAUTION: In advance install a switchbox to the wall where the touch panel
controller is to be installed.
z
The diagram of the mounting plate screw hole positions
5-13/16 (147)
2-1/16 (53)
2 (51)
1/４ (7)
3-3/4 (95)
8-5/16 (211)
7-1/16 (180)
3-9/16 (90)
3/8 (10)
5-9/16 (142)
7-7/16 (189)
2-15/16 (74.2)2-1/4 (56.7)
2-7/16 (62.6) 1/2 (12.4)
5-11/16 (145)
7-1/2 (190)
3/8 (10)
2-1/4 (57)
1/2 (12)
2-R3/8 (4)
R1/8 (2.5)
2-R1/8 (2.5)
3/16 (R5)
2-Ø15/16 (23.7)
Unit : in. (mm)
CAUTION: Refer to the mounting screw hole positions of the switchbox that
is to be installed in advance and check the compatibility.
- (05 - 45) -
CONTROL
SYSTEM
CONTROL
SYSTEM