Installation Manual

En-1
2. STANDARD PARTS
The following installation parts are supplied. •
Use them as required.
Name and shape Q’ty
Installation manual
(This manual)
1
Operating manual
1
Grille
1
Bracket frame
1
Screw-A
10 mm
16
Screw-B
10 mm
6
Cable clip
2
Binder
3
Bushing
1
3. DIMENSION
Diagrams showing connection between bracket frame and Grille are given below.
UTD-G*SA
[Top View] Unit : mm
74
29
P200×3=600
263
2 × Ø5 hole
645
4 × Ø3.2 burring hole
Bushing (*1)
116
130 180
683
555
23
249
216
[Front View]
35
78
148
2 × Ø3.2
burring hole
Ø3.2
Inner Diameter (ID)
of the bushing
Ø5 hole
74
29
942
84
[Side View]
INSTALLATION MANUAL
PART NO. 9380267010
AIR CONDITIONER
OPTIONAL PARTS
Auto Louver Grille
For authorized service personnel only.
1. SAFETY PRECAUTIONS
• Be sure to read this Manual thoroughly before installation.
• The warnings and precautions indicated in this Manual contain important
information pertaining to your safety. Be sure to observe them.
• Hand this Manual, together with the Operating Manual to the customer.
Request the customer to keep them on hand for future use, such as for relocating
or repairing the unit.
WARNING
This mark indicates procedures which, if improperly
performed, might lead to the death or serious injury of the
user.
Install at a location that can sufficiently withstand the weight. If the strength is
inadequate, grille may fall and cause an injury.
Firmly install the grille. Or else, it may fall and cause an injury.
Do not turn ON the power until all work has been completed. Turning ON the
power before the work is completed can cause serious accidents such as electric
shock or fire.
Never touch electrical components immediately after the power supply has been
turned off. Electrical shock may occur. After turning off the power, always wait 5
minutes or more before touching electrical components.
CAUTION
This mark indicates procedures which, if improperly
performed, might possibly result in personal harm to the
user, or damage to property.
Do not install the unit in the following areas
In the upper part of the vicinity of room entrance. It may cause condensation •
on the outlet port.
Near a wall surface. It may cause condensation on the wall during cooling.•
Area fi lled with mineral oil or containing a large amount of splashed oil or •
steam, such as a kitchen.
Perform heat insulation and field setting according the manual. Not installing as
per the instructions may cause condensation.
Do not move the up-down louvers manually. It may cause a malfunction.
Don’t install the unit where it will be exposed to direct sunlight. Or else, it may
cause a change in color.
When the installation area is exposed to direct sunlight, take measures to block
the light such as covering the grille surface with a sheet. Or else, it may cause a
change in color.
Use an appropriate Grille that is compatible with the indoor unit. Refer to Design
& Technical manual for further details. If not used with the correct combination, it
may cause condensation.
Contents
1. SAFETY PRECAUTIONS ................................................................ 1
2. STANDARD PARTS ......................................................................... 1
3. DIMENSION ..................................................................................... 1
4. LOCATION ....................................................................................... 2
5. INSTALLATION METHOD................................................................ 2
5.1. Mounting the bracket frame ...................................................... 2
5.2. Mounting the grille .................................................................... 3
6. WIRING-INSIDE THE EQUIPMENT ................................................ 3
6.1. For Type-A ................................................................................ 3
6.2. For Type-B ................................................................................ 3
7. WIRING-OUTSIDE THE EQUIPMENT ............................................ 4
8. FIELD SETTING .............................................................................. 4
9. TEST OPERATION .......................................................................... 4
EnglishEspañolPortuguês DeutschItalianoРусский FrançaisEλληvIkάTürkçe
9380267010_IM.indb 19380267010_IM.indb 1 1/12/2011 9:40:50 AM1/12/2011 9:40:50 AM