User manual
Table Of Contents
- FUJITSU Tablet STYLISTIC Q736
- Contents
- Innovative technology
- Ports and controls
- Important notes
- First-time setup of your device
- Working with the Tablet PC
- Status indicators
- Switching on the Tablet PC
- Switching the Tablet PC off
- Handwriting recognition
- Touch screen
- Select display orientation (portrait or landscape orientation)
- Using fingers
- Using the pen
- Tablet buttons
- Camera
- Rechargeable battery
- Using the power-management features
- Memory cards
- SIM card
- Wireless LAN€/ Bluetooth€/ UMTS€/ LTE / NFC wireless components (dependent on configuration)
- Ethernet and LAN (only cradle or keyboard dock)
- GPS
- Accessories for your Tablet PC (optional)
- Security functions
- Connecting external devices
- Settings in BIOS Setup Utility
- Starting the BIOS Setup Utility
- Operating BIOS Setup Utility
- Exiting BIOS Setup Utility
- Exit Saving Changes - save changes and exit BIOS Setup Utility
- Exit Discarding Changes – Discard changes and exit BIOS Setup Utility
- Load Setup Defaults – Copy Standard Entries
- Discard Changes – Discard changes without exiting the BIOS Setup Utility
- Save Changes - save changes without exiting the BIOS Setup Utility
- Save Changes and Power Off
- Troubleshooting and tips
- Executing a reset
- Help if problems occur
- The Tablet PC's date or time is incorrect
- Battery charging indicator not lit
- The Tablet PC's touchscreen remains dark
- The display on the Tablet PC's touchscreen is difficult to read.
- The external monitor remains blank
- The external monitor is blank or the image is unstable
- The cursor does not correctly follow the pen movements
- Pen input not working
- The Tablet PC does not start after switch on
- The Tablet PC stops working
- The printer does not print
- The wireless connection to a network does not work
- The battery discharges too quickly
- SmartCard reader is not recognised.
- SmartCard PIN forgotten
- User and/or supervisor SmartCard lost
- SmartCard lost
- Acoustic warnings
- Error messages on the screen
- Restoring the system under Windows€10
- Technical data
- Manufacturer’s notes
- Index
Manufacturer’s notes
Radio frequencies used
RF module Frequency band Max. transmission po w er
1 BT 2400-2480 MHz 100 mW
2
NFC
13.56 MHz 20 mW
3 WLAN 2410-2480 MHz 100 mW
4 WLAN 5150-5350 MHz class 2 200 mW
5
WLAN 5470-5725 MHz class 1 1 W
6
GSM
850 MHz, 900 MH z 2 W
7
UMTS
1900 MHz, 1800 MHz 500 mW
8 LTE 2100 MHz, 2600 MHz 500 mW
9 LTE 850 MHz, 900 MHz 2 W
Other certification marking s
Certificationmarkings
Any other certification markings are listed in the "Manual Appendix -
Additional Certifications" supplement.
If such markings a re available, you can fin d the supplement on the Internet at
"
http://support.ts.fujitsu.com/Ma nuals/" with the Operating Manual for your device .
Regulatory notices
If there is no FCC logo and also no FC C ID on the device then this device is
not approved by the Federal Co mmunications Commission (FCC) of the USA.
Although it is not explicitly forbidden to travel in the US trading area carrying this
device, to avoid trouble at customs clearan ce, Fujitsu Techn ology Solutions GmbH
recommends not to bring this device into the US trading area.
Regulatory information for Tablet PCs without wireless device
Regulatoryinformation
NOTICE:
Changes or modifications not exp ressly a pproved by F ujitsu Technology Solutions
could void this user’s authority to operate the equipment.
Notice to Users of Radios and Television
These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate wireless frequen cy energy
and, if not installed and used in accordan ce with the instructions, may cause harmful interference
to wireless communications. However, there is no guarantee that interferen ce will not occur in a
particular installation. If this equipment does cause harmful interference to wireless or television
reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct t he interference by one or more of th e following measures:
• Reorient or relocate the receiving ant enna.
• Increase the separation between the eq uipm ent and receiver.
Fujitsu 93