Datasheet

System configurator and order-information guide
F
PRIMERGY TX300 S5 Status 2009-09-29
Section
III
Memory
- There are 9 memory slots for max. 72GB DDR3 RAM per CPU available with 8GB DIMMs
=> max. 144GB for two CPU`s ( 72GB per CPU )
( For explanation of following terms refer to section "Memory Configurations"
- The memory area is divided into 3 channels per CPU with 3 slots per channel
- Slot 1 of each channel belongs to memory bank 1, the slot 2 belongs to memory bank 2 and
slot 3 belongs to memory bank 3
No mix of dual rank and quad rank modules possible for the configuration of the same CPU
1.) In the independent channel mode is following configuration possible
- Each slot can optionally be equipped with 2GB single rank, 4GB and 8GB dual rank DDR3 modules or
with 8GB quad rank DDR3 modules
2.) In the spare channel mode is following configuration possible
- Each memory bank can optionally be equipped with 3x2GB single rank,
3x4GB and 3x8GB dual rank DDR3 modules or with 3x8GB quad rank DDR3 modules
Each slot of one bank has to be equipped with identical modules for spare channel mode
In channel A and B of CPU 1 or channel D and E of CPU 2 are always the active memory modules,
in channel C of CPU 1 and channel F of CPU 2 is always the spare module
3.) In the mirrored channel mode is following configuration possible
- Each memory bank can optionally be equipped with 2x2GB single rank,
2x4GB and 2x8GB dual rank DDR3 modules or with 2x8GB quad rank DDR3 modules
In each memory bank channel A and B of CPU 1 or channel D and E of CPU 2 have to be equipped with
identical modules for mirrored channel mode. Channel C of CPU 1 and channel F of CPU 2 is not equipped
In channel B is always the mirrored memory of channel A of CPU 1
In channel E is always the mirrored memory of channel D of CPU 2
DDR3 1066 and 1333MHz modules can be mixed, but run always with the slower speed.
With three DIMMs per channel only 800MHz is possible.
- For each CPU minimum 1 memory module has to be configured in Independent Channel Mode
( => Additional memory extensions can still be configured up to eight times per CPU ) or
one bank has to be equipped with two modules (channel A+B for CPU 1 or D+E for CPU 2) in
Mirrored Channel Mode
( => Additional memory extensions can still be configured up to two times per CPU ) or
one bank has to be equipped with three modules (channel A+B+C for CPU 1 or D+E+F for CPU 2)
in Spare Channel Mode or Performance Mode
( => Additional memory extensions can still be configured up to two times per CPU )
- ECC with SDDC (Chipkill) is standard for TX300 S5.
For a description of memory configurations refer to section "Memory Configurations"
Minimum one memory module or order code per CPU = first memory
Registered (reg) RDIMMs
Note 1.)
For "independent channel mode" usage! Max. DDR3 memory speed depends on the memory configuration
- One DDR3-1066 PC3-8500 reg ECC memory module
of one CPU memory channel and on the speed of the CPU itself.
Memory 2GB (single rank) S26361-F3284-E513 The memory channel with the lowest speed defines the speed
Memory 4GB (dual rank) S26361-F3284-E514 of all CPU channels in the system, also for the channels of the
Memory 8GB (dual rank) S26361-F3284-E515 second CPU if configured.
One DIMM per channel = max. 1333MHz,
Choose up to 9 order codes above per CPU. two DIMMs per channel = max. 1066MHz,
three DIMMs per channel = max. 800MHz,
9x for each CPU
with max.
3 modules Registered (reg) RDIMMs
per channel For "independent channel mode" usage!
- One DDR3-1333 PC3-10600 reg ECC memory module Note 2.)
Memory 2GB (single rank) S26361-F3285-E513 Max. DDR3 memory speed 1333MHz is only
Memory 4GB (dual rank) S26361-F3285-E514 possible with CPU`s X5550 and X5570
Memory 8GB (dual rank) S26361-F3285-E515
Choose up to 9 order codes above per CPU.
G1 G2
Fujitsu Technology Solutions x86 PRIMERGY Server 13 of 30