fi-6010N Network Scanner Getting Started Contents 3.3 Setting the Scanner Name ................................................. 7 Introduction ................................................................................. iii ■ Manuals ........................................................................................... iii ■ Regulatory Information ................................................................. iii ■ Note of Liability ...........................................................
fi-6010N Network Scanner Getting Started Introduction ■ Note of Liability Thank you for purchasing the fi-6010N Network Scanner. This easy-to-operate network scanner is used to scan documents for further use. encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is located.
fi-6010N Network Scanner Getting Started PFU LIMITED International Sales Dept., Imaging Business Division, Products Group Solid Square East Tower, 580 Horikawa-cho, Saiwai-ku, Kawasaki-shi Kanagawa 212-8563, Japan Phone: (81-44) 540-4538 How Trademarks are Indicated in This Manual All Rights Reserved, Copyright© PFU LIMITED 2008. Windows® XP Windows Vista® Windows Server® 2003 Windows Server® 2008 .
fi-6010N Network Scanner Getting Started Do not touch the inside of the scanner unless necessary. Do not cover the scanner with something during its operation. Do not take apart or modify the scanner. The inside of the scanner contains highvoltage components. Touching these components might cause electric shock or fire. Do not use the scanner while covered with a blanket, etc. Doing so may raise the temperature inside and cause a fire. Do not use the scanner where it gets wet.
fi-6010N Network Scanner Getting Started Scanner Features Chapter 1 1.2 Logging In The scanner functions available after login vary in the following ways for different types of user: For more details, refer to the "Operator's Guide". • Administrator Can setup and manage the scanner. • Regular User Can scan documents and then send, print, or save the resulting data. 1.
fi-6010N Network Scanner Getting Started 1.5 Names and Functions of Parts Chapter 2 ■ Removable Parts Parts that can be removed from the scanner are displayed below. This section describes the scanner parts and their functions. Pad assembly Startup button ADF paper chute 2.2 Installing the Scanner Pick roller Side guides Sheet guide Top cover 2.
fi-6010N Network Scanner Getting Started Chapter 3 2.4 Attaching the Keyboard Cover 3.1 Logging in Top-center guide The layout of the keyboard may differ according to the language selected for the operating environment. The layout of each keyboard cover is prepared according to language requirements. Take the keyboard cover for the selected language out of its packaging, and attach it to the scanner. This scanner is set up for use with an English (US) keyboard.
fi-6010N Network Scanner Getting Started 4. Enter the "Current Password", "New Password", and "Confirm New Password". Passwords must be between 7 and 127 characters long. Alphanumeric characters (case sensitive) and symbols may be entered. 3. Press the [List] button for the "Timezone" input field. 4. Press the [OK] button. ⇒ The restart confirmation screen appears. The default timezone is "(GMT+09:00) Osaka, Sapporo, Tokyo". ⇒ A list of timezones appears. 5. Press the [Later] button. 4.
fi-6010N Network Scanner Getting Started 3.6 Setting the Admin Network 3. Set the scanner's IP address. This may be done automatically, by pressing the DHCP [On] button. The IP address may also be set manually, by pressing the DHCP [Off] button and entering the following numerical addresses: Set the network settings for connecting to a scanner from the Admin Tool or Central Admin Server. 1. Select the [Network Settings] tab on the top menu. • IP Address • Subnet Mask • Default Gateway 2.
fi-6010N Network Scanner Getting Started 4. Enter the following numerical addresses: 5. Press the [Ping] button. ⇒ A ping test is performed and the results are • Primary WINS • Secondary WINS If a WINS server setting is not required, enter "0.0.0.0". displayed. If the result shows "Lost=0 (0% loss)", the network connection is functioning normally. For any other result, refer to "Checking Basic Network Operation with a Ping Test" (page 23). A Secondary WINS cannot be set without a Primary WINS.
fi-6010N Network Scanner Getting Started Chapter 5 • Downloading is not possible while ATTENTION an administrator or user operation is being processed. • Do not close the Web browser or logout until installation is complete. ATTENTION Installation will fail if the length of any installation path (folder path plus installation file name) exceeds 259 characters. Select an installation folder that respects this limit. ⇒ The "File Download - Security Warning" screen appears. 5. Press the [Run] button.
fi-6010N Network Scanner Getting Started Chapter 6 Performing a Scan Test 7. Check the scanned data. If no document is loaded • Message Document not found. Load a document into the ADF, making sure the side guides are adjusted correctly and try again. • Action Load a document, and try the scan test again. If a multifeed is detected • Message Feed Error: Document(s) may not match the set paper size, ADF may have grabbed more than one sheet, or documents may not be suitable for scanning.
fi-6010N Network Scanner Getting Started Appendix A If some other error occurs • Message An error has occurred. Try turning the power off and back on again. The administrator should contact the FUJITSU scanner dealer or an authorized FUJITSU scanner service provider for help.
fi-6010N Network Scanner Getting Started Appendix B CAUTION WARNING Scanner Care ■ Which Parts and When The glass scanner windows inside the ADF can become hot when the scanner is used. Before cleaning inside the scanner or replacing any parts, turn off the power, unplug the AC adapter from the outlet, and wait for at least 15 minutes. The power does not need to be turned off when cleaning the feed rollers. Clean all parts after every 1,000 sheets scanned.
fi-6010N Network Scanner Getting Started Appendix C CAUTION Replacing Parts The glass scanner windows inside the ADF can become hot when the scanner is used. ATTENTION Before cleaning inside the scanner or replacing any parts, turn off the power, unplug the AC adapter from the outlet, and wait for at least 15 minutes. ■ Part No. and Replacement Cycle for Carrier Sheet Use only the PFU LIMITED parts specified. Do not use consumable parts made by other manufacturers.
fi-6010N Network Scanner Getting Started Appendix D Network Connection Troubleshooting If a server cannot be connected to by using its IP address, and does not respond to a ping test, try the following steps: ■ Checking Basic Network Operation with a Ping Test If a network connection is not possible, refer to "3.9 Checking the Network Connection" (page 11) for ping results and how to deal with them.
fi-6010N Network Scanner Getting Started No. 6 Problem Action The network link speed/duplex mode for the scanner and server are invalid, or Auto-Negotiation is not supported by the server. For this scanner, the default [Link Speed/Duplex Mode] setting is "Auto-Negotiation". On the "Network Status" screen, match the scanner and server's network link speed/duplex mode settings.
fi-6010N Network Scanner Getting Started Appendix E Problem Scanner cannot be turned on. Scanning does not start. Even after pressing the top cover [SCAN] button, scanning does not start. Multifeed errors occur frequently.
fi-6010N Network Scanner Getting Started Copyright NetAdvantage 2007 Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: Copyright 2000-2007 Infragistics, Inc. 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
The name of Juniper Networks may not be used to endorse or promote products derived from this software without specific prior written permission. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3.
