P3PC-2242-01EN fi-6670(A)/fi-6770(A)/fi-6750S Thank you for purchasing a fi-6670(A) / fi-6770(A) / fi-6750S Color Scanner series. This Getting Started is the startup guide that summarizes the preparatory actions needed before use. Be sure to thoroughly read this manual before you start using the scanner. Contents Introduction....................................................................2 Regulatory Information .................................................2 Conventions...........................
Introduction Thank you for purchasing our fi-6670(A)/fi-6770(A)/fi-6750S series Color Image Scanner. Scanner Models This manual covers the following five scanner models, each featuring as: Model fi-6670 fi-6670A Description Equipped with an automatic document feeder (ADF) for automatic document feeding and duplex scanning. The fi-6670A comes with a color graphics adapter (CGA) board as a standard feature. It enables advanced image processing at a high speed when used with Kofax VRS.
Conventions The use of a shielded interface cable is required to comply with the Class B limits of Part 15 of FCC rules. The length of the Power cable must be 3 meters (10 feet) or less. assumes no liability whatsoever for damages arising from use of this product by the user in high-safety applications, and for any claims or compensation for damages by the user or a third party.
*1) Where there is no distinction between the different versions of the above operating system, the general term "Windows" is used. *2) All the descriptions in this manual assume the usage of Adobe Acrobat bundled with this product. However, Adobe Acrobat may be upgraded without notice. If the descriptions differ from the screens actually displayed, refer to the Adobe Acrobat Help. Arrow Symbols in This Manual The user must not perform repairs on this scanner.
Safety Information Safety Information Warning Indications Used In This Manual The following indications are used in this manual to obviate any change of accident or damage to you and/or the equipment. WARNING This indication alerts operators to an operation that, if not strictly observed, may result in severe injury or death. CAUTION This indication alerts operators to an operation that, if not strictly observed, may result in safety hazards to personnel or damage to equipment.
Unplug the scanner when a trouble occurs. Immediately unplug the scanner when a trouble occurs. Never cut the ground connection until the scanner is unplugged from the Power outlet. Do not disassemble the scanner. Do not take apart or modify the scanner. The inside of the scanner contains high-voltage components. Touching these components might cause electric shock or fire. CAUTION The following are important cautions described in this manual Do not install the scanner on an unstable work table.
Safety Information Disconnect the power plug from the Power outlet when the scanner is not in use for a long period of time. When the scanner is not going to be used for a long period of time, be sure to disconnect the power plug from the Power outlet. Do not install the scanner in direct sunlight. Do not install the scanner under direct sunlight or near heating apparatus. Doing so might cause excessive heat to build up inside the scanner, which can cause scanner trouble or even fire.
1 Preparation Contents of the Scanner Package When you open the scanner package, handle the main unit and its attachments carefully. Make sure the scanner package contains all the parts listed in the package contents list that is included in the package box. If any parts are missing or defective, contact your FUJITSU scanner dealer or an authorized FUJITSU scanner service provider. Part Names and Functions This section describes the scanner parts and their functions.
1 Preparation ■ fi-6770/fi-6770A/fi-6750S (Flatbed type) Chute Roller Cover ADF (automatic document feeder) ADF Paper Chute Stacker Paper Chute Extension Stacker Extension Side Guide Side Guide Button Stopper Operator Panel Flatbed Transport Lock Document Cover ADF Lock Screw Handle Document Holding Pad Lock Screw Storage Hole Document Bed ADF Open Button fi-6770 SCSI ID Switch CGA Board Slot SCSI Connector 1 fi-6770A Ventilation Port USB Connector 1 CGA Board Power Connector Main Powe
■ Model-Common Parts Brake Roller (x1) (consumable) Pick Arm (x1) Brake Roller Holder (x1) Ultrasonic Sensor (x2) (for multifile detection) Feed Roller (x4) Plastic Roller (x4) Chute Roller (x1) (Usually covered with a hood) Glass (x2) Pick Roller Cover (x1) Sheet Guide (x2) Pick Roller (1 x 2 types) (consumable) Functions of the Operator Panel The Operator Panel is comprised of a Function Number Display, buttons, and LEDs, which are used to operate the scanner and to check the scanner status.
1 Preparation ■ Flatbed type Check Check LED Function Number Display Function [Function] button Send to [Send to] button Scan / Stop [Scan/Stop] button Power [Power] button/Power LED Name Description Check LED Lights (in orange) when an error occurs. Function Number Display Indicates the scanner status. [Function] button Switches the function activated by the [Send to] button. [Send to] button Launches linked application software for scanning. Resets an error indication.
2 Installing the Scanner The following describes how to install the scanner. 1 Place the scanner at its installation site. The outer dimensions and the spaces required for installing the respective scanner types are as follows: (Unit: mm/inches) ADF type Flatbed type 390 (15.3) 300 (11.8) 432 (17.0) 686 (27.0) 640 (25.1) 342 (13.4) 700 500 (27.5) (19.6) 329 (13.0) 1179 (46.4) 690 (27.1) 1030 (40.5) Outer dimensions Installation space 2 Unlock the Transport Lock (Flatbed type only).
2 Installing the Scanner 3) Gently close the Document Cover. 4) Change the position of the ADF. CAUTION • Be careful not to pinch your fingers when moving the ADF. • Never rotate the ADF by more than 180 degree. Doing so may damage the ADF. The ADF can be set to any of the following three positions: After repositioning the ADF, be sure that the ADF is firmly locked to the new position.
3 Connecting the Cables The following describes how to connect the cables between the scanner and your computer. The type of the connector for the cable depends on the scanner model you use. Confirm the scanner model and use the correct cable.
3 Connecting the Cables 1 2 3 Make sure that the computer is turned OFF. Open the Cable Cover (ADF type only). Connect the scanner to your computer either with a USB or SCSI cable. • You cannot make both USB and SCSI cable connections at the same time. • You cannot connect multiple computers to the scanner at the same time. • If Kofax VRS is not used on the fi-6670A or fi-6770A, connect the cable to USB Connector 1 or SCSI Connector 1 on the scanner.
4 Installing the Scanner Software Brief Information on the Bundled Software To scan documents with this scanner, you must install a scanner driver for operating the scanner as well as scanning software (hereinafter called the "application") for launching the driver and performing a scan. The scanner drivers and applications provided with the scanner are as follows: ■FUJITSU TWAIN 32 [TWAIN Driver] (*1) Conforms to the TWAIN standard. Used when you operate the scanner using TWAIN-compliant applications.
4 Installing the Scanner Software ■Adobe Acrobat 8.1 Standard A de-facto standard application used for creating, editing, managing, and making use of digitalized documents in PDF format. *1: The product ID used for its installation differs from the official product name. It is shown in [ ].
Installing the Bundled Software The following describes how to install the bundled software from the “SETUP DVD-ROM” contained in the scanner package. You can select either the [INSTALL (Recommended)] or [INSTALL (Custom)] menu when installing the SETUP DVD-ROM. The former installs all the software programs needed to operate the scanner; the latter installs the selected software programs one by one. For how to install Adobe Acrobat, refer to "Installing Adobe Acrobat" (on page 21) in the next section.
4 Installing the Scanner Software 4 5 6 Click the [INSTALL (Recommended)] button. DThe list of scanners appears. Select the scanner model name you will be using. Then, click the [Next] button. Install the software, following the on-screen instructions. INSTALL (Custom) This menu lets you select and install the required software programs one by one. The procedure for custom-installing the required software is as follows: If an old version of the software is installed already, uninstall it first.
3 Insert the SETUP DVD-ROM into your DVD drive. D The [FUJITSU Image Scanner Setup] screen appears. If this screen does not appear, find "Install.exe" in the DVD-ROM using "Windows Explorer" or "Computer" and execute it directly. 4 Click the [INSTALL (Custom)] button. DThe [INSTALL PRODUCTS] screen appears. 5 Click the button for the software to be installed. 6 Install the software, following the on-screen instructions. Repeat Steps 5 and 6 to install other software program(s) here.
4 Installing the Scanner Software Installing Adobe Acrobat The following describes how to install Adobe Acrobat using the "Adobe Acrobat DVD-ROM" provided with this scanner. You do not have to install Adobe Acrobat if it is already installed on your computer. 1 Insert the Adobe Acrobat DVD-ROM into your DVD drive. D The DVD-ROM is recognized automatically, and the "Adobe® Acrobat® Installer for Fujitsu Scanners" appears. If the setup dialog box does not appear, find "Install.
5 Test-Scanning Documents Using ScandAll PRO, you can test-scan documents to check if they are scanned with the ADF correctly. For how to scan documents with the flatbed, refer to “Chapter 5 Various Documents” in the Operator’s Guide. The following describes how to test-scan a document: 1 Turn on the scanner. 1) Press the “I” side of the main power switch of the scanner. 2) Press the [Power] button on the Operator Panel. The scanner is turned ON, and the Power LED on the Operator Panel lights in green.
5 Test-Scanning Documents 4 Load a sheet into the scanner. 1) Load the document on the ADF Paper Chute face down. 2) Align the side guides to the width of the document. 3) Pull out the Stacker to the length of the document, and then raise the Stopper. 5 6 7 Launch ScandAll PRO. Select the [start] menu D [All Programs] D [Fujitsu ScandAll PRO] D [Fujitsu ScandAll PRO]. Select the [Tool] menu D [Preferences]. D The [Setup] dialog box appears.
If “Kofax VRS Scanner“ does not appear in the list, check if the interface cable is properly connected to SCSI/USB Connector 2. If “Kofax VRS Scanner“ does not appear even after you have connected the cable properly, then refer to “Chapter 8 Troubleshooting“ in the Operator’s Guide. 10 Select the [Scan] menu D [Scan Settings]. D The [Scan Settings] dialog box appears. 11 Clear the [Save to file] checkbox. You only check the operation now, so you do not have to save to file.
5 Test-Scanning Documents ■ Kofax VRS Configure scan settings, and then click the [OK] button. 14 In the [Scan Settings] dialog box, click the [Scan] button. D The scanned document images are displayed in the ScandAll PRO window. Refer to “Chapter 8 Troubleshooting” in the Operator’s Guide, in case you see a number and an alphabet displayed on the Function Number Display.
fi-6670(A)/fi-6770(A)/fi-6750S Image Scanner Getting Started P3PC-2242-01EN Issue Date: May 2008 Issued by: PFU LIMITED • Copying of the contents of this manual in whole or in part and copying of the scanner application is prohibited under the copyright • The contents of this manual are subject to change without notice. • PFU LIMITED is not liable whatsoever for any damages resulting from use of this scanner and procedures described in this manual, profit due to defects, and any claims by a third party.
