Fujitsu F9600 Telephone System LinkPlus Interface Guide SpectraLink 6000 System SpectraLink 8000 System June 2008 Edition 1725-3634-001 Version E
LinkPlus Interface Guide: Fujitsu F9600 Telephone System Trademark Information Notice Polycom® and the logo designs SpectraLink® LinkPlus Link NetLink SVP Are trademarks and registered trademarks of Polycom, Inc. in the United States of America and various countries. All other trademarks used herein are the property of their respective owners. Polycom, Inc. has prepared this document for use by Polycom personnel and customers.
About this Guide Polycom is the market leader in multi-cellular wireless telephone systems for the workplace. We manufacture a range of products to suit any size installation. All Polycom products use our LinkPlus digital integration technology to integrate with various digital switch platforms. Using LinkPlus technology, Wireless Telephones (handsets) emulate digital telephone sets to deliver advanced capabilities such as multiple line appearances and LCD display features.
LinkPlus Interface Guide: Fujitsu F9600 Telephone System Related Documents SpectraLink 6300 MCU : Operator’s Console (1725-36125-001) SpectraLink 6100 MCU: Installation and Operation (1725-36097-001) SpectraLink 6020 Wireless Telephone and Accessories User Guide (1725-36092-001) Available at http://www.polycom.com/usa/en/support/voice/proprietary_wire less/proprietary_wireless.
About this Guide Icons and Conventions This manual uses the following icons and conventions. Caution! Follow these instructions carefully to avoid danger. Note these instructions carefully. Label PN: 1725-36134-001_E.doc This typeface indicates a key, label, or button on SpectraLink hardware.
1 Plan the Interface The system administrator programs the telephone system for use with the handset System using the normal administration terminal or procedures. Programming can be done after the handsets are registered. Recommended programming includes assigning extension numbers to the handsets and programming features on the telephone system so they are easily accessible from the handsets. For analog interfaces, macro codes are in the document relating to configuring the system.
LinkPlus Interface Guide: Fujitsu F9600 Telephone System “model” handsets then use the model as a template to program the other handsets. • All handsets are different: All handsets are programmed differently, so each handset will be programmed individually. Before installation, the parameters of the wired phones should be verified to plan the parameters required for the handsets. Directory number and equipment number The handset supports a total of nine line resources.
Plan the Interface The system administrator may use the Extension Assignments Worksheet at the end of this document to track the port numbers, extensions, users, and features assigned to handsets. The Wireless Telephone Display The SpectraLink Wireless Telephone will display the telephone number as it is dialed. The DT14DS has a two-line by 20-character display. The handset display is 2 lines by 16 characters; therefore, some F9600 messages may be truncated when displayed on the handset.
LinkPlus Interface Guide: Fujitsu F9600 Telephone System Feature Programming Requirements When planning the interface, the following information must be taken into account: Line sequences The handset uses two types of key sequences to access PBX features and multiple lines. LINE sequences are those where the user presses the LINE key and then a number key. The key-map design designates “line” keys that should be programmed for line appearance so that they correspond to line sequences on the handset.
Plan the Interface SpectraLink 6100 MCU For the SpectraLink 6100 MCU, the handset function menu text can only be changed via remote configuration through the services of Polycom’s Customer Support. SpectraLink 8000 Telephony Gateways Function menu text options can be changed in the Administration Console of the SpectraLink 8000 Telephony Gateways.
LinkPlus Interface Guide: Fujitsu F9600 Telephone System Autodial FAB10 through FAB13 may be used for up to 4 Autodial numbers per handset. Specifics are described later in this document. Ring types Handset ring types (soft, normal, vibrator, etc.) are programmed by the handset user and are not accessible or changeable by the system switch. Whenever possible the audible ringer on the handset will follow the cadence provided by the system switch.
2 Interface Implementation This section describes the recommended programming to use the SpectraLink 6000 System (MCU) or SpectraLink 8000 Wireless Telephone system (Gateway) with a Fujitsu F9600 telephone system. The procedures assume: • The F9600 is installed and operational in an approved configuration. See the Telephone Switch Interface Matrix document for tested configurations.
LinkPlus Interface Guide: Fujitsu F9600 Telephone System SpectraLink 8000 Telephony Gateways Connect to the SpectraLink 8000 Telephony Gateway using the serial or modem interface. From the Main Menu, choose Gateway Configuration. Scroll to Telephone Switch Type and press enter to change this field, from the Submenu of PBX types, select Fujitsu. Refer to SpectraLink 8000 Telephony Gateway: Administration Guide for SRP for details on configuring the Telephone Switch Type.
Interface Implementation The FCN +[number] and LINE+[number] labels represent the key sequence on the handset mapped to the corresponding key on the desk set. The handset function menu default settings are shown on each corresponding button in the above diagram; these may be changed as described above in Function Menu Programming. Some of these functions (Mute, Redial, Forward, etc.) are activated by softkeys or FCN menu options on the SpectraLink 6000 and SpectraLink 8020/8030 Wireless Telephones.
LinkPlus Interface Guide: Fujitsu F9600 Telephone System Note that the TYPE must be 3. The other parameters in the brackets can be the default values. Other related commands: CHA MLDT, DEL MLDT, DIS MLDT Clear programmable buttons The programmable buttons are probably assigned to a default button pattern. Perform the following to clear all buttons (button 00 will not be cleared since this is the prime-line button).
Interface Implementation Note: The following features should not be assigned to the PTB 4xx, and should not be assigned to other SpectraLink Wireless Telephones if they are not supported on the handset: • AUTO ANSWER • DIAL-BY-NAME • All DATA features • FORCED CALL FORWARD • FLEXIBLE CALL FORWARD • HEADSET • All TCSI features When programming is complete, the installer can test the handsets.
LinkPlus Interface Guide: Fujitsu F9600 Telephone System Using the Autodial feature 1. To use the Autodial feature, perform the following steps: 2. Press START on the same handset that was programmed above. 3. Press the Autodial key sequence for the number to be dialed (FCN +4, FCN +5, FCN +9, or FCN +*). The pre-programmed number is then dialed. 4. Wait for your party to answer. 5. Press END when the call is completed.
3 Extension Assignments Worksheet Shelf: _______ Interface Module: _______ Handset 1 Interface Module Circuit # 1 Handset 2 2 Handset 3 3 Handset 4 4 Handset 5 5 Handset 6 6 Handset 7 7 Handset 8 8 Handset 9 9 Handset 10 10 Handset 11 11 Handset 12 12 Handset 13 13 Handset 14 14 Handset 15 15 Handset 16 16 Handset # Ext. # PN: 1725-36134-001_E.
