Supplement for Embedded MegaRAID SATA User’s Guide CA97232-0014-01EN Supplement for Embedded MegaRAID SATA User’s Guide 1 / 13
Supplement for Embedded MegaRAID SATA User’s Guide Contents ¾ Before reading this manual .......................................................................................................................................................... 3 ¾ About the change in the Array controller display name according to the driver's update.................................. 3 ¾ “Product Names” (page 3) ............................................................................................................
Supplement for Embedded MegaRAID SATA User’s Guide ¾ Before reading this manual This document is to supplement the description to the Embedded MegaRAID SATA User’s Guide. Please also refer to the “Safety Precautions” and “Embedded MegaRAID SATA User’s Guide” accompanied with “Array Controller Document & Tool CD” when this document is used. Note: The page number in bracket indicates the page in the Current User’s Guide for your reference purpose.
Supplement for Embedded MegaRAID SATA User’s Guide ¾ “Product Names” (page 3) Include the following information when the “Table: Abbreviation of Product Names” on P.3 of the User’s Guide is referred.
Supplement for Embedded MegaRAID SATA User’s Guide z Updating Drivers (Windows Server 2008 – Full installation) The update procedure for the device driver using Windows Server 2008 is as follows; 1 Log on to Windows with Administrator privileges. 2 Insert the “Array Controller Document & Tool CD” into a CD/DVD drive. 3 Select [Diagnostics] -> [Device Manger] from [Server Manger]. 4 Double-click [Storage controllers]. The Controllers list appears.
Supplement for Embedded MegaRAID SATA User’s Guide z Updating Driver (Windows Server 2008 – ServerCore Installation) 1 Log on to Windows with Administrator privileges. 2 Insert “Array Controller Document & Tool CD” into the CD/DVD drive. 3 Execute the command below from the command prompt. ・For Windows Server 2008 pnputil -i -a [CD/DVD Drive]:\Drivers\MegaSR\W2K8\MegaSR.INF ・For Windows Server 2008 x64 pnputil -i -a [CD/DVD Drive]: \Drivers\MegaSR\W2K8x64\MegaSR.
Supplement for Embedded MegaRAID SATA User’s Guide ¾ “4.1.3 Access Privileges to ServerView RAID” (page 58) As for “■ User privilege”, the description is slightly modified as follows; Current User’s Guide (ServerView RAID V2.x.xx-xx or previous): ■ User privilege The User privileges are mainly used to see the status of the array controllers, hard disks, and logical drives. To use the User privileges, log in to ServerView RAID Manager with any of the user names and passwords registered with the OS.
Supplement for Embedded MegaRAID SATA User’s Guide Step 6 Once the system is up and running, create and configure a Windows user account. Regarding the above, the description is change as follows; Current User’s Guide: (ServerView RAID V2.x.xx-x or previous) Users Account for User Privileges 1. Create a user account for the User privileges of ServerView RAID. Make sure that the user account for the User privileges does not belong to the “raid-adm” group. ServerView RAID V3.x.
Supplement for Embedded MegaRAID SATA User’s Guide ¾ “4.4.4 Uninstallation of HDD Check Scheduler” (page 71) The procedure of the “4.4.4 Uninstallation of HDD Check Scheduler” on page 71 is partially modified as follows; Step 2 Click [Start] button – [All Programs] (or [Programs]) – [Accessories] – [Command Prompt]. The above procedure is no longer needed when ServerCore is installed with Windows Server 2008.
Supplement for Embedded MegaRAID SATA User’s Guide ¾ “4.7.1 Viewing and Changing Array Controller Settings” (page 84) When using ServerView RAID V3.0.14-00 or later, following setting is displayed under [settings] tab, but This function is not supported. Option Logical drive number for boot Default Value 0 Initial Value 0 Description Not supported ¾ “4.7.3 Setting ServerView RAID” (page 87) When using ServerView RAID V3.0.
Supplement for Embedded MegaRAID SATA User’s Guide ¾ “4.9.2 Checking Array Controller Status” (page 98) When using driver version of V10.xx or later, As for “4.9.2 Checking Array Controller Status” on page 98, include the information as follows; Item Adapter Category BIOS version BIOS build time Description Version number of the expansion ROM BIOS for the array controller. BIOS build time of the expansion ROM BIOS for the array controller. ¾ “5.1.
Supplement for Embedded MegaRAID SATA User’s Guide Description Not detecting hard disks and unmatched insert locations The displayed message is different according to the situation. [Message 1] WARNING! BIOS detected configured disks w. some drive(s) missing, pls power off the system, remove the drive from port:XX and reinsert it in another slot. Press any key to continue. (*Press any key, and the following message appears.) If you proceed, you'll lose this configuration. Press any key to continue.
Supplement for Embedded MegaRAID SATA User’s Guide Supplement for Embedded MegaRAID SATA User’s Guide CA97232-0014-01EN Issued on Sep, 2008 Issued by FUJITSU LIMITED ● The contents of this manual may be revised without prior notice. ● Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual. ● No part of this manual may be reproduced in any form without the prior written permission of Fujitsu.
