User's Manual
Table Of Contents
- FUJITSU Tablet STYLISTIC Q665
- Contents
- Declarations of conformity 7
- Fujitsu Contact Information 8
- Ports and controls 10
- Important notes 14
- First-time setup of your device 19
- Working with the Tablet PC 23
- Settings in BIOS Setup Utility 72
- Troubleshooting and tips 75
- Technical data 85
- Manufacturer’s notes 91
- Declarations of conformity 94
- FCC and IC Regulatory Information 95
- Appendix 99
- Index 114
- Fujitsu Shopping Online
- Maintaining Latest Configuration
- Limited Warranty
- Ports and controls
- Front (figure does not show the water-resistant device variant)
- Right side (top - water-resistant device variant, bottom - non water-resistant device variant)
- Additional safety notes for devices with wireless components
- Protecting the display screen
- Energy saving
- Traveling with your Tablet PC
- Waterproof/dustproof (device-dependent)
- Cleaning the Tablet PC
- Cleaning with disinfectant wipes
- Unpacking and checking the device
- Choose a location
- Connecting the AC adapter
- Switching on the device for the first time
- Switching the Tablet PC on
- Switching the Tablet PC off
- Handwriting recognition
- Touchscreen
- Select display orientation (portrait or landscape format)
- Using fingers
- Using the stylus
- Tablet buttons
- Webcam
- Rechargeable battery
- Using the energy saving functions
- Memory cards
- SIM card
- Ethernet and LAN (only with performance docking cradle)
- GPS
- Your performance docking cradle (optional)
- Keyboard docking station (optional)
- Intermediary VESA Mount Plate (optional)
- Hand strap (optional)
- Security functions
- Configuring the fingerprint sensor
- Using the Security Lock
- SmartCard reader (optional)
- Trusted Platform Module - TPM (device dependent)
- Connecting an external monitor
- Connecting USB devices
- Connecting external audio devices
- Settings in BIOS Setup Utility
- Starting the BIOS Setup Utility
- BIOS Setup Utility operation
- Exiting BIOS Setup Utility
- Exit Saving Changes - save changes and exit BIOS Setup Utility
- Exit Discarding Changes - Reject changes and exit BIOS Setup Utility
- Load Setup Defaults – load default values
- Discard Changes - Discard Changes without exiting BIOS Setup Utility
- Save Changes - save changes without exiting the BIOS Setup Utility
- Save changes and power off
- Executing a reset
- Help if problems occur
- Recovering your Factory Image
- The Tablet PC’s date or time is incorrect
- The printer does not print
- Acoustic warning
- WLAN specifications
- Rechargeable battery
- Keyboard docking station (optional)
- Cover (optional)
- DOC (Industry CANADA) Notices
- ENERGY STAR Compliance
Appendix
Enter
Determining whether Recovery and Utility is pre-loaded
1.
Turn on or reboot your system. When the Fujitsu logo appears, press the key.
2.
Use the key to get to the Application Menu.
3.
Check whether the Recovery and Utility option is present. If it is not present, it means
that t
he utility must be used from the Bootable Disk. Proceed to “Running Recovery and
Utility f
rom the Bootable Disk” if Recovery and Utility is unavailable.
Running Recovery and Utility from hard disk
1.
Turn on or reboot your system. When the Fujitsu logo appears, press the
key.
2.
Use the key to get to the Application Menu.
3.
Cursor down to Recovery and Utility and press the key.
4.
Choose your language, if necessary. Select Recovery and Utility to proceed.
5.
Three tool options appear: Diagnostics, Recovery, and Utility (refer to the Recovery and
Utility t
ools section below for instructions on how to use these tools).
6.
If this was successful please skip the next step and go to “Recovery and Utility tools.”
7.
If this was NOT successful, please go to the next step.
Running Recovery and Utility from the Bootable disk
To verify/change the boot-up priority (rather than booting-up from the hard drive or
an external media drive), perform the following steps:
1.
Power on your system. When the Fujitsu logo appears on the screen, press the
2.
Insert the bootable disk into the drive tray.
3.
Highlight the CD/DVD option from the Boot menu, then press
Enter
.
4.
Click OK.
key.
5.
Select CD/DVD boot mode: UEFI Mode, if applicable, and then press .
While the files are being loaded from the disk, the Fujitsu logo screen will appear
followed by a pr
ogress bar at the bottom of the screen.
F12
Tab
F12
Tab
Enter
F12
Fujitsu 107