User's Manual
Table Of Contents
- FUJITSU Tablet STYLISTIC Q665
- Contents
- Declarations of conformity 7
- Fujitsu Contact Information 8
- Ports and controls 10
- Important notes 14
- First-time setup of your device 19
- Working with the Tablet PC 23
- Settings in BIOS Setup Utility 72
- Troubleshooting and tips 75
- Technical data 85
- Manufacturer’s notes 91
- Declarations of conformity 94
- FCC and IC Regulatory Information 95
- Appendix 99
- Index 114
- Fujitsu Shopping Online
- Maintaining Latest Configuration
- Limited Warranty
- Ports and controls
- Front (figure does not show the water-resistant device variant)
- Right side (top - water-resistant device variant, bottom - non water-resistant device variant)
- Additional safety notes for devices with wireless components
- Protecting the display screen
- Energy saving
- Traveling with your Tablet PC
- Waterproof/dustproof (device-dependent)
- Cleaning the Tablet PC
- Cleaning with disinfectant wipes
- Unpacking and checking the device
- Choose a location
- Connecting the AC adapter
- Switching on the device for the first time
- Switching the Tablet PC on
- Switching the Tablet PC off
- Handwriting recognition
- Touchscreen
- Select display orientation (portrait or landscape format)
- Using fingers
- Using the stylus
- Tablet buttons
- Webcam
- Rechargeable battery
- Using the energy saving functions
- Memory cards
- SIM card
- Ethernet and LAN (only with performance docking cradle)
- GPS
- Your performance docking cradle (optional)
- Keyboard docking station (optional)
- Intermediary VESA Mount Plate (optional)
- Hand strap (optional)
- Security functions
- Configuring the fingerprint sensor
- Using the Security Lock
- SmartCard reader (optional)
- Trusted Platform Module - TPM (device dependent)
- Connecting an external monitor
- Connecting USB devices
- Connecting external audio devices
- Settings in BIOS Setup Utility
- Starting the BIOS Setup Utility
- BIOS Setup Utility operation
- Exiting BIOS Setup Utility
- Exit Saving Changes - save changes and exit BIOS Setup Utility
- Exit Discarding Changes - Reject changes and exit BIOS Setup Utility
- Load Setup Defaults – load default values
- Discard Changes - Discard Changes without exiting BIOS Setup Utility
- Save Changes - save changes without exiting the BIOS Setup Utility
- Save changes and power off
- Executing a reset
- Help if problems occur
- Recovering your Factory Image
- The Tablet PC’s date or time is incorrect
- The printer does not print
- Acoustic warning
- WLAN specifications
- Rechargeable battery
- Keyboard docking station (optional)
- Cover (optional)
- DOC (Industry CANADA) Notices
- ENERGY STAR Compliance
Appendix
Creating a Backup of Bootable Disk and Recovery Image
When you purchased your new system, a copy of the recovery image was loaded into a
hidden partition on your hard disk drive. Having a copy of the recovery image available to
you means that in the event of system failure, you will be able to restore it and re-install
the essential access software using Fujitsu Software Auto Installer.
To make a copy of the recovery image to DVD disks, you will need three or four blank
disks to create the copy. After creating the copy, be sure to label the disks and keep
them in a safe place to ensure they do not get damaged.
Note: If your system does not have an internal writable DVD drive, connect your
system to an external drive* before beginning the following steps.
1.
Launch System Restore and Recovery from the desktop icon. It will allow you to create
the B
ootable Disk and the Recovery Image Disk Set.
2.
On “Step 1: Select the Bootable Disk from the list”:
a.
Select a media type.
b.
Notice the number of disks that are needed for the set.
c.
Click Next to proceed.
3.
On “Step 2: Confirm your Recovery Disk”, click Next.
4.
On “Step 3:” follow the on-screen instructions to make the disk or disk set, then click
Start. It takes approximately 20 minutes to make one disk.
5.
On “Step 4”, when the disk creation is completed, a message appears.
Click F
inish to exit the program.
6.
Repeat Step 1: Select Recovery Disk from the list and repeat the above
steps 2
(a), 2(b), 2(c), 3, 4 and 5.
* DEPENDING UPON YOUR OPTICAL DRIVE AND MEDIA FORMAT USED, SOME MEDIA
TYPES MAY BE INC
OMPATIBLE FOR CREATING IMAGE BACKUPS.
Fujitsu 105