4.4 Charging i. Charging the HHC ‘When charging the HHC by the Vehicle charger, follow these steps: (13 HHC is mounted on the Vehicle charger. The charge lamp of HHC lights up in orange during charge of a battery. (2) The charge will be completed for approximately 3 hours, The lamp will be changed to green when completed. Note While the HHC is on, the battery is not correctly charged. Note If the charging terminal is dirty, the battery may not be charged.
4.5 Specifications Lie Specifications Charging Charging time About 3 hours (1 cell) Power supply DC12V/24V (an automobile battery) Temperature and Operating 0 to +400 humidity temperature and 109% 0 S0%RH humidity Charging to +40°C Storage temperature | -20 to +60°C and humidity 5% to OS%RH Dimensions and weight About 250mm(W) x 90mm{D} x 70mm(H) About 0.
4.6 Cleaning Cover Clean the cover with a cloth moistened with prophylaxis alcohol, with a cloth dipped a water and synthetic detergent solution and squeezed dry, or with a dry cloth. If the second choice is used, be sure to squeeze as much water as possible out of the cloth. Detergent entering the holder can cause a failure. If thinner, benzene, or other volatile solvent is used for cleaning, colors may change or letters may disappear.
Chapter 5 Multi charger 5.1 Outline ® Outline When the Team Pad 400G Series HHC is mounted on a Multi charger, the HHC can be charged. Four battery packs in HHS can be charged at a time.
.2 Component Names ‘The Multi charger can be set with two ways as shown below.
5.3 Connection 1. Connecting to a AC adapter ‘When connecting the Multi charger to a HHC, follow these steps: (1) Connect the AC adapter to the DC IN jack of Multi charger. The AC adapter is not included with the package of the Multi charger, It should be purchased separately. (23 Fix a clamp attached the power cord to the Multi charger. 2.Connecting to a HHC (1) Open the rustproof cover of one unit that will be used.
5.4 Charging 1. Charging the HHC ‘When charging the HHC by this Mali charger, follow these steps: (1) HHC is mounted on the Mali charger. The charge lamp of HHC lights up in orange during charge of a battery. (2) ‘The charge will be completed for approximately 3 hours. The Jap will be changed to green when completed, Note While the HHC is on, the battery is not correctly charged. Note If the charging terminal is dirty, the battery may not be charged.
5.5 Specifications Rem Specifications Charging Charging time About 3 hours (1 cell} Power supply AC100-240V, 50/60Hz Temperature and Operating {to +40°C humidity temperature and humidity Charging 0 to +40°C Storage temperature | -20 fo +60°C and humidity 5% 10 O5%RH Dimensions and weight About 241mm(W) x 125mm(D) x 1 73mm(H) About 2.
5.6 Cleaning Cover Clean the cover with a cloth moistened with prophylaxis alcohol, with a cloth dipped a water and synthetic detergent solution and squeezed dry, or with a dry cloth. If the second choice is used, be sure to squeeze as much water as possible out of the cloth. Detergent entering the holder can cause 4 failure. If thinner, benzene, or other volatile solvent is used for cleaning, colors may change or letters may disappear.
Chapter 6 USB adapter 6.1 Outline Mounting the Team Pad 400G Series HHC on the USR adapter enables you to communicate with the host computer, as well as recharge its internal battery pack. 6.2 Component Names Front View Back View Charge pin Communication pin Communication Lamplighter) DIN USB connector 6.3 Operations Summary Mount a battery-loaded HHC into the USB adapter, and battery recharging starts {with the charge lamp of HHC being illuminated).
6.4 Connection Follow the procedure stated below to connect the USB adapter with the master unit. 6.4.1 Connection with the AC Adapter. 1. Plug the power cord to the USB adapter. Power cord 6.4.2 Connection with the USB cable 1, Attach the USB cable (FHTCB271) to the USB connector of the USB adapter. The USB cable is not included with the package of the USB adapter. It should be purchased separately. 2. Fix a clamp attached the USB cable (FHTCB271) to the USE adapter.
6.4.3 Connection with the Master Unit L 2. 3 Unplug the power cord of the USB adapter from the wall outlet and switch off the master unit. Attach the USB cable (FHTCB271) to the USB connector of the master unit. Plug the power cord of the USE adapter in a wall outlet and switch on the master nit after making sure that the cable connections are correct. 6.4.4 Connection with the HHC 1. Make sure that the communication pin of USB adapter and communication pin of the HHC are clean. 2.
6.5 Communication 1. Plug the USB adapter power cord in a wall outlet. Insert it in the USB adapter, and Place the HHC in communication state, The communication lamp on the USB adapter lights green during communication. 3. The communication lamp switches off when the communication ends normally. NOTE Data may be lost if the power cord of the USB adapter is unplugged from the wall outlet during communication. Do not unplug the USB adapter power cord before communication ends.
6.6 Recharging Follow the procedure below by using the USB adapter to recharge the HHC. (1) Log the USB adapter power cord in a wall outlet. (2) Confirm that the required is mounted. (33 Connect the HHC to the USB adapter, recharge begins, (4) The charge lamp lights orange during recharge. (5) The charge will be completed for approximately 3 hours. The lamp will be changed to green when completed, NOTICE Keep the HHC switched off during recharge.
6.7 Specifications Rem Specification Communication Connection c .
Chapter 7 LAN adapter 7.1 Outline Mounting the Team Pad 400G Series HHC on the LAN adapter enables you to communicate with the host computer, as well as recharge its internal battery pack. 7.2 Component Names Front View Back View Communication pin Communication lamp (green) DCN LAN connector 7.3 Operations Summary Mount a battery-loaded HHC into the LAN adapter, and battery recharging starts (with the charge lamp of HHC being illuminated).
7.4 Connection Follow the procedure stated below to connect the LAN ADAPTER with the master unit. 7.4.1 Connection with the AC Adapter. Plug the power cord to the LAN adapter Power cord 7.4.2 Connection with the LAN cable Attach the LAN cable to the USB connector of the LAN adapter. The LAN cable is not included with the package of the LAN adapter. It should be purchased separately.
7.4.3 Connection with the Master Unit 1. Unplug the power cord of the LAN adapter from the wall outlet and switch off the master unit. 2. Attach the LAN cable to the LAN connector of the master unit, 3. Plug the power cord of the LAN adapter in a wall outlet and switch on the master unit after making sure that the cable connections are correct. 7.4.4 Connection with the HHC 1. Make sure that the communication pin of LAN adapter and communication pin of the HHC are clean. 2.
7.5 Communication 1. Plug the LAN adapter power cord in a wall outlet, 2. Insert tin the LAN adapter, and Place the HHC in communication state, The communication lamp on the LAN adapter lights green during communication. 3. The communication lamp switches off when the communication ends normally. NOTE Data may be lost if the power cord of the LAN adapter is unplugged from the wall outlet during communication. Do not unplug the LAN adapter power cord before communication ends.
7.6 Recharging Follow the procedure below by using the LAN adapter to recharge the HHC, {1) Log the LAN adapter power cord in a wall outlet. (2) Confirm that the required is mounted. (3) Connect the HHC to the LAN adapter, recharge begins. (4) The charge lamp lights orange during recharge, (5) The charge will be completed for approximately 3 hours. The Tamp will be changed to green when completed. NOTICE Keep the HHC switched off during recharge.
7.7 Specifications Rem Specifications HHC/LAN adapter interface (USB UF) USB (LAN IF) Host computer/LAN adapter interface Communications indicator Green LED illuminated for the duration of communication, off at a successful ending of the session of communication. Charge function Charge time About 3 hours {cell} Power supply IGNACIO 240 V, 50/60 Hz Temperature Operating 0 to +40°C Charging 0 to +40°C Storage =20°C to +60°C Humidity Operating 10°C to 90% RH Storage 5 tw 95%RH Dimensions JAW) Weight About 0.
