answers 2 Technisches Handbuch / Technical Manual Mainboard D1522 / D1521 Deutsch / English / Français
Sie haben ... ... technische Fragen oder Probleme? Wenden Sie sich bitte an: • Ihren zuständigen Vertriebspartner • Ihre Verkaufsstelle Aktuelle Informationen und Updates (z. B. BIOS-Update) zu unseren Mainboards finden Sie im Internet: http://www.fujitsu-siemens.com/mainboards Are there ... ... any technical problems or other questions you need clarified? Please contact: • your sales partner • your sales outlet The latest information and updates (e.g.
Dieses Handbuch wurde auf Recycling-Papier gedruckt. This manual has been printed on recycled paper. Ce manuel est imprimé sur du papier recyclé. Este manual ha sido impreso sobre papel reciclado. Questo manuale è stato stampato su carta da riciclaggio. Denna handbok är tryckt på recyclingpapper. Dit handboek werd op recycling-papier gedrukt. Herausgegeben von/Published by Fujitsu Siemens Computers GmbH Bestell-Nr./Order No.
Deutsch English Mainboard D1522 / D1521 Technisches Handbuch Technical Manual Ausgabe Januar 2003 January 2003 edition Français
Intel, Pentium und Celeron sind eingetragene Warenzeichen der Intel Corporation, USA. Microsoft, MS, MS-DOS und Windows sind eingetragene Warenzeichen der Microsoft Corporation. PS/2 und OS/2 Warp sind eingetragene Warenzeichen von International Business Machines, Inc. Alle weiteren genannten Warenzeichen sind Warenzeichen oder eingetragene Warenzeichen der jeweiligen Inhaber und werden als geschützt anerkannt.
Übersicht/Overview Mainboard D1522 / D1521 1= 2= 3= 4= Interne Anschlüsse und Steckplätze / Internal connectors and slots 21 DIMM 2 DIMM 1 CPU Pentium 4 1 2 3 4 20 5 6 7 8 9 AGP 19 18 17 5= 6= 7= 8= 9= 10 = 11 = 12 = 13 = PCI 1 PCI 2 PCI 3 10 16 14 13 11 15 12 Externe Anschlüsse / External connectors LAN 14 = 15 = 16 = 17 = 18 = 19 = 20 = 21 = Stromversorgung / Power Supply Diskettenlaufwerk / Floppy disk drive IDE-Laufwerke 3/4 / IDE-drives 3/4 Stromversorgungsüberwachung / Power supply mo
Contents Mainboard D1522 / D1521................................................................................................................1 Notational conventions ..............................................................................................................1 Important notes..................................................................................................................................2 Information about boards ...........................................................
Mainboard D1522 / D1521 Your mainboard is available in different configuration levels. Depending on the configuration chosen, some of the hardware components described may not be available on your mainboard. Further information Information on the BIOS Setup and additional descriptions of the drivers are contained: • • • in the readme files on your hard disk on the driver floppy disks included on the CD "Drivers & Utilities Collection" or "Drivers & Utilities" or "ServerStart".
Mainboard D1522 / D1521 Important notes With the mainboard installed you must open the system to access the mainboard. How to dismantle and reassemble the system is described in the operating manual accompanying the system. Connecting cables for peripherals must be adequately shielded to avoid interference. ! Observe the safety notes in the operating manual of your system. Incorrect replacement of the lithium battery may lead to a risk of explosion.
Mainboard D1522 / D1521 List of features Onboard features D1522-A D1521-A Chipset i845GE i845GE Board size µ-ATX µ-ATX ! ! VGA ! ! Buzzer / int. Speaker Support -/! -/! LAN / with Alert-on-LAN !/! !/- ! ! Audio HI-SPEED USB 2.0 !/- -/- Temperature monitoring ! - System Monitoring ! - Fujitsu Siemens Computers Keyboard Power Button Support ! ! DIMM Sockets (DDR SDRAM, PC2100/1600) 2 2 AGP Slot (2/4x, 32 bit, 66 MHz, 1.5 V) 1 1 PCI slot (32 bit, 33 MHz, 5 V and 3.
Mainboard D1522 / D1521 External ports VGA Audio Mic. in / Line in / Line out (2 x 0,5 W / 8 Ω) 1 1 1/1/1 1/1/1 Game/MIDI - - LAN (RJ-45) 1 1 1/1 1/1 USB Ports (2.0, ~480 Mb/s) 2 2 Serial Ports (FIFO, 16550 compatible) 1 1 Parallel Port (EPP/ECP) 1 1 PS/2 mouse/keyboard * for use with internal devices or optional Front or Rear panel ** not supported by standard power supplies Special technical features – special features Your mainboard is available in different configuration levels.
Mainboard D1522 / D1521 Logo Boot A customer-specific logo can be displayed during system booting. The logo is loaded using the LogoFlash tool. The logo can have a size of 640 x 480 pixels with 16 colours. The tool is provided on the CD "Drivers & Utilities" or "Drivers & Utilities enhanced" or is available on the Internet at http://www.fujitsu-siemens.com/mainboards.
Brief instructions on installing mainboard Brief instructions on installing mainboard If you have purchased a separate mainboard, you can install the mainboard in your system in accordance with the following brief instructions. The activities described here assume a basic knowledge of PCs and cannot be carried out by a layperson. If you are not sure whether you have the necessary specialised knowledge, then leave this work to an expert. The illustrations of the system show examples of possible cases.
Brief instructions on installing mainboard Ê Should no suitable connection field be provided in the case, then you must install the connection field (1) provided. Ensure the plate is aligned properly so that the connections are suitable for the mainboard later. Ê Set the mainboard on the edge on which the connection field is located (2) and then insert the board in the case (3). Make sure that spacers in the housing are only mounted at points at which there are mounting holes in the mainboard.
Interfaces and connectors Interfaces and connectors The positions of the interfaces and connectors are shown on page "Cover". The components and connectors marked are not necessarily present on the mainboard. External ports The positions of the external ports are shown on page "Cover".
Interfaces and connectors Graphics port - Supported screen resolutions Depending on the operating system used, the screen resolutions in the following table refer to the mainboard screen controller. If you are using an external screen controller, you will find details of supported screen resolutions in the operating manual or technical manual supplied with the controller.
Interfaces and connectors Pin assignment of internal ports The pin assignment of some internal connections is shown in English in the following. i Some of the following connectors may be optional! Front panel Watch the poling of the LEDs. The positive pole of the connection cables is often indicated with a coloured wire. Power On/Off Message LED Sleep LED 1) Power On Sleep 1) HD-LED LED 1) 3) 1) Reset 1 2 SCSI LED Input 1) 2) Speaker 1) Cable is not included in the delivery scope.
Interfaces and connectors Power On LED II 1 Pin Note 1 2 3 Power On LED (Anode) Power On LED (Anode) Power On LED (Cathode) 3 1 Power supply ATX 11 Pin Signal Pin Signal 1 2 3 4 5 6 7 8 9 10 +3.3 V (P3V3P) +3.3 V (P3V3P) GND +5 V (VCC) GND +5 V (VCC) GND Powergood (high asserted) +5 V Auxiliary (VCC Aux) +12 V (P12VP) 11 12 13 14 15 16 17 18 19 20 +3.
Interfaces and connectors 1 Fan 1 (system fan - supervised) Pin 1 2 Signal GND Controlled Fan voltage (0 V, +6 V ... +12 V, max. 1 A) or fix Fan voltage (+12 V, max. 1 A) Fan sense 3 1 Fan 2 (system fan - supervised) Pin Signal 1 2 GND Controlled Fan voltage (0 V, +6 V ... +12 V, max. 1 A) or fix Fan voltage (+12 V, max.
Interfaces and connectors USB C/D / E/F - dual channel 1 2 11 12 (internal or external via special wire) Pin Signal Pin Signal 1 3 5 7 9 11 Key VCC C Data negative C Data positive C GND Key 2 4 6 8 10 12 Chipcard reader on VCC D Data negative D Data positive D GND Not Connected 1 Intrusion for case open detect for optional push-button (opener) Pin Signal 1 2 3 GND Case open (low asserted) Intrusion switch present (low asserted) 1 Audio S/PDIF (2-pin) Pin Signal 1 2 GND SPDIF out A
Interfaces and connectors 1 Audio S/PDIF (3-pin) Pin Signal 1 2 3 GND SPDIF out GND 1 Audio front panel 2 Pin Signal Pin Signal 1 3 5 7 9 Micro input Micro bias Right line output NC Left line output 2 4 6 8 10 Analog GND Analog VCC Right line return Key Left line return CD-ROM audio 1 Pin Signal 1 2 3 4 Left CD audio input CD GND CD GND Right CD audio input Processor power supply 3 1 Pin Signal Pin Signal 1 3 GND GND 2 4 +12 V +12 V 14 - English A26361-D1522-Z120-3-6319
Settings with switches and jumpers Settings with switches and jumpers Your mainboard is equipped with switches or jumpers. The positions of the switches or jumpers are shown on page "Cover".
Add-on modules / Upgrading Add-on modules / Upgrading ! Exit energy-saving mode, switch off the system and remove the power plug from the mains outlet, before carrying out any of the procedures described in this chapter! Even when you have switched off the device, parts (e.g. memory modules, AGP and PCI extension boards) are still supplied with power. Installing and removing processors Technical data Intel Pentium 4 with 400 or 533 MHz front side bus in the mPGA478 design.
Add-on modules / Upgrading Mounting heat sink Be sure to use heat conducting material between the processor and the heat sink. If a heat conducting pad (rubber-like foil) is already applied to the heat sink, then use it. Otherwise you must apply a very thin layer of heat conducting paste. Heat conducting pads can only be used once. If you remove the heat sink, you must clean it and apply new heat conducting paste before you remount it.
Add-on modules / Upgrading Upgrading main memory Technical data Technology: DDR 266 or DDR 333 unbuffered DIMM modules 184-pin; 2.5 V; 64 Bit, no ECC Total size: 128 Mbytes up to 2 Gbyte DDR-SDRAM Granularity: 32, 64, 128, 256, 512 or 1024 Mbyte for one socket A current list of the memory modules recommended for this mainboard is available on the Internet at: www.fujitsu-siemens.de/mainboards. At least one memory module must be installed.
Add-on modules / Upgrading Removing a memory module 1 1 Ê Ê Push the clips on the right and left of the compartment outward (1). Pull the memory module from the compartment (2). Upgrading AGP screen controllers Technical data: The AGP slot supports the modes 1x/2x/4x with 32 bits and 66 MHz. Only 1.5 V AGP screen controllers are supported. i Some older 3.3 V AGP screen controllers are coded like 1.5 V AGP screen controllers. The installation of such 3.
Add-on modules / Upgrading PCI bus interrupts - Selecting correct PCI slot i To achieve optimum stability, performance and compatibility, avoid the multiple use of ISA IRQs or PCI IRQ Lines (IRQ sharing). Should IRQ sharing be unavoidable, then all involved devices and their drivers must support IRQ sharing. PCI IRQ Lines connect AGP slots, PCI slots and onboard components to the interrupt controller. PCI IRQ Lines are permanently wired on the mainboard.
Add-on modules / Upgrading Replacing lithium battery In order to permanently save the system information, a lithium battery is installed to provide the CMOS-memory with a current. A corresponding error message notifies the user when the charge is too low or the battery is empty. The lithium battery must then be replaced.
Add-on modules / Upgrading BIOS update When should a BIOS update be carried out? Fujitsu Siemens Computers makes new BIOS versions available to ensure compatibility to new operating systems, new software or new hardware. In addition, new BIOS functions can also be integrated. A BIOS update should always also be carried out when a problem exists that cannot be solved with new drivers or new software. Where can I obtain BIOS updates? The BIOS updates are available on the Internet at www.fujitsu-siemens.
Add-on modules / Upgrading BIOS Recovery - Recovering System BIOS i All BIOS settings are reset to the default values. Ê Ê Open the casing as described in the operating manual. Ê Ê Ê Close the casing as described in the operating manual. Ê Ê Open the casing as described in the operating manual. Ê Ê Ê Ê Ê Close the casing as described in the operating manual. Set the switch for "Restore system BIOS" to ON or plug the corresponding jumper (see "Settings with switches and jumpers" chapter).
Add-on modules / Upgrading Safety for processor on Fujitsu Siemens Computers mainboards If the processor uses an old or incorrect microcode, error-free operation cannot be ensured. Fujitsu Siemens Computers has therefore implemented a function on its mainboards that interrupts the booting process if no suitable microcode is available for the installed processor. The output error message is Patch for installed CPU not loaded. Please run the bios flash update diskette.
Annex Annex Electrical Properties Loadability for connections and fuses i Make sure that the connected devices do not overload the connections. Fuse No. Fuse Connection Maximum loadability 1 750 mA 2 3 4 5 6 7 500 mA 500 mA 500 mA 500 mA 500 mA 500 mA Keyboard Mouse VGA connector USB port A USB port B USB port C USB port D USB port E USB port F Not specified Not specified Minimum 50 mA 500 mA 500 mA 500 mA 500 mA 500 mA 500 mA The fuses on this mainboard can be used several times (polyfuses).
Annex APM and ACPI system status, energy-saving modes System status ACPI Status* APM Status Power LED Sleep LED Power consumption Wake-up time Normal operation G0 S0 On To Off Normal Simple energysaving mode G1 S1 Standby Off To Almost like normal Almost immediate ly S3 RAM, wake-up components ca. 5s S4 Wake-up components ca.
Annex Mainboard Revision and BIOS Version The compatibility, e.g. with new processors, can be independent of the BIOS version or the revision status of the mainboard used. The CPU and BIOS compatibility lists are available on the Internet at www.fujitsu-siemens.de/mainboards. Mainboard: Revision level The revision status of the mainboard exactly identifies which mainboard you have.
Error messages Error messages This chapter contains error messages generated by the mainboard. Available CPUs do not support the same bus frequency – System halted! Memory type mixing detected Non Fujitsu Siemens Memory Module detected – Warranty void There are more than 32 RDRAM devices in the system Check whether the system configuration has changed. If necessary, correct the settings.
Error messages DMA test failed EISA CMOS not writable Extended RAM Failed at offset: nnnn Extended RAM Failed at address line: nnnn Failing Bits: nnnn Fail-Safe Timer NMI failed Multiple-bit ECC error occurred Memory decreased in size Memory size found by POST differed from EISA CMOS Single-bit ECC error occurred Software NMI failed System memory exceeds the CPU’s caching limit System RAM Failed at offset: nnnn Shadow RAM Failed at offset: nnnn Switch the device off and on again.
Error messages Missing or invalid NVRAM token Switch the device off and on again. If the message is still displayed, please contact your sales outlet or customer service centre. Monitor type does not match CMOS - RUN SETUP Correct the entry for the monitor type in the Main menu of the BIOS Setup. On Board PCI VGA not configured for Bus Master In the BIOS Setup, in the Advanced menu, submenu PCI Configuration, set the Shared PCI Master Assignment entry to VGA.
Error messages System battery is dead - Replace and run SETUP Replace the lithium battery on the mainboard and redo the settings in the BIOS Setup. System Cache Error - Cache disabled Switch the device off and on again. If the message is still displayed, please contact your sales outlet or customer service centre. System CMOS checksum bad - - Default configuration used Call the BIOS Setup and correct the previously made entries or set the default entries.
Error messages SmartCard reader - error messages This chapter contains error messages generated by the SmartCard reader (chipcard reader). Boot access denied The Sicrypt SmartCard has no access rights to the system. Check your chipcard Either the Sicrypt SmartCard has been wrongly inserted, or it is not a PC-Lock Sicrypt card. Chipcard reader FAIL An error has occurred on the serial port to the SmartCard reader (chipcard reader).
Error messages Glossary The technical terms and abbreviations given below represent only a selection of the full list of common technical terms and abbreviations. Not all technical terms and abbreviations listed here are valid for the described mainboard.
