Datasheet

Technical details
PRIMERGY TX150 S6
Housing type Floorstand Floorstand Floorstand Floorstand Rack Rack Rack Rack
Hard disk architecture 3.5” SAS/
SATA
3.5” SAS/
SATA
2.5” SAS 2.5” SAS 3.5” SAS/
SATA
3.5” SAS/
SATA
2.5” SAS 2.5” SAS
Power supply Standard Hotplug Standard Hotplug Standard Hotplug Standard Hotplug
Mainboard
Mainboard type D 2559
Chipset Intel
®
3210
Processor quantity and type 1 x Intel
®
Celeron
®
processor / Intel
®
Pentium
®
Dual-Core processor / Intel
®
XEON
®
processor 3000 sequence
Processor options Intel
®
Celeron
®
440 (1C, 2.00 GHz, SLC: 512 KB, 800 MHz, 35 W)
Intel
®
Core™2 Duo E7200 (2C, 2.53 GHz, SLC: 3 MB, 1066 MHz, 65 W)
Intel
®
Pentium
®
E2140 (2C, 1.60 GHz, SLC: 1 MB, 800 MHz, 65 W)
Intel
®
Pentium
®
E2200 (2C, 2.20 GHz, SLC: 1 MB, 800 MHz, 65 W)
Intel
®
Xeon
®
E3110 (2C, 3.00 GHz, SLC: 6 MB, 1333 MHz, 65 W)
Intel
®
Xeon
®
E3120 (2C, 3.16 GHz, SLC: 6 MB, 1333 MHz, 65 W)
Intel
®
Xeon
®
L3110 (2C, 3.00 GHz, SLC: 6 MB, 1333 MHz, )
Intel
®
Xeon
®
X3220 (4C, 2.40 GHz, SLC: 2x4 MB, 1066 MHz, 95 W)
Intel
®
Xeon
®
X3360 (4C, 2.83 GHz, SLC: 2x6 MB, 1333 MHz, 95 W)
Intel
®
Xeon
®
X3370 (4C, 3.00 GHz, SLC: 2x6 MB, 1333 MHz, 95 W)
Memory slots 4 (2 banks with 2 slots each)
Memory slot type PC2-6400 (unbufferd DIMM DDR2 800 ECC)
Memory capacity (min. - max.) 1 GB - 8 GB
Memory Protection Advanced ECC
Memory notes Mix and match possible; with dual channel operation better performance (2 modules with equal capacity
necessary). Single channel (1 module) conguration possible.
Memory options 2 GB (1 module(s) with 2 GB), DDR2, 800 MHz
1 GB (1 module(s) with 1 GB), DDR2, 800 MHz
Upgrade notes For a memory and processor upgrade a BIOS update may be required.
Interfaces
USB ports 8 x USB 2.0 (1x front, 4x rear, 3x internal)
Graphics (15-pin) 1 x VGA
Serial 1 (9-pin) 1 x serial RS-232-C, usable for iRMC or system or shared
Serial 2 (9-pin) 1 x serial RS-232-C (optional)
Parallel (25-pin) 1 x Centronics 25-pin EPP/ECP compatible (option)
Mouse / Keyboard (PS/2) 2
LAN / Ethernet (RJ-45) 1 x Gbit/s Ethernet
Service LAN (RJ45) 1 x dedicated service LAN port for iRMC S2 (10/100 Mbit/s)
Service LAN trafc can be switched to shared onbord Gbit LAN port
Onboard or integrated Controller
Integrated RAID Controller Integrated RAID 0/1 or RAID 5/6 controller for SAS base units (occupies one PCIe slot).
See under Components RAID controller
SATA Controller Intel
®
ICH9R, 2 ports used for accessible drives
4 port for internal SATA HDDs with RAID 0, 1, 10 for Windows and Linux; RAID 5 iButton optional
LAN Controller BCM 5755, 10/100/1000 Mbit/s Ethernet, PXE-Boot via LAN from PXE server, iSCSI Boot (also diskless) via
onboard LAN
Remote Management Controller Integrated Remote Management Controller (iRMC S2, 32 MB attached memory incl. graphics controller), IPMI
2.0 compatible
TPM Inneon / 1.2 (option)
Slots
PCI-Express x8 2 x short
PCI-Express x4 (mech. x8) 1 x short
PCI slots 3 x PCI 32/33 MHz, 2x long, 5V
Slot Notes in SAS conguration 1x PCI-Express occupied by modular RAID controller
Drive bays
Accessible drive bays 3 x 5.25/1.6-inch
1 x 3.5/1-inch for FDD
Notes accessible drives all possible options described in relevant system congurator
Drive bays (Base unit specic)
Hard disk bays 4 x 3.5-inch
hot-plug
SAS/SATA
4 x 3.5-inch
non hot-plug
SATA
8 x 2.5-inch
hot-plug
SAS
8 x 2.5-inch
hot-plug
SAS
4 x 3.5-inch
hot-plug
SAS/SATA
4 x 3.5-inch
hot-plug
SAS/SATA
8 x 2.5-inch
hot-plug
SAS
8 x 2.5-inch
hot-plug
SAS
Optional hard disk bays 2 x 3.5-inch
hot-plug
HDD box
2 x 3.5-inch
hot-plug
HDD box
- - 2 x 3.5-inch
hot-plug
HDD box
2 x 3.5-inch
hot-plug
HDD box
- -
Operating panel
Operating buttons On/off switch
NMI button
Reset button