Operating instructions

En-8
TIMER OPERATION
Before using the timer function, be sure that the Remote Controller is set to the correct current time (see page 5).
To Use the ON timer or OFF timer
1
Press the START/STOP button [Fig. 6 (6-9)]
(if the unit is already operating, proceed to step 2).
The indoor unit’s OPERATION Indicator Lamp (green) [Fig. 4 (4-1)] will light.
2
Press the TIMER MODE button [Fig. 6 (6-5)] to select
the OFF timer or ON timer operation.
Each time the button is pressed the timer function changes in the following order:
CANCEL OFF ON
PROGRAM (OFF  ON, OFF  ON)
The indoor unit’s TIMER Indicator Lamp (orange) [Fig. 4 (4-2)] will light.
3
Use the TIMER Set buttons [Fig. 6 (6-14)] to adjust the
desired OFF time or ON time.
Set the time while the time display is fl ashing (the fl ashing will continue for
about 5 seconds).
button: Press to advance the time.
button: Press to reverse the time.
After 5 seconds, the display will return to the original state.
To Cancel the Timer
Use the TIMER MODE button to select “CANCEL”.
The air conditioner will return to normal operation.
To Change the Timer Settings
Perform steps 2 and 3.
To Stop Air Conditioner Operation while
the Timer is Operating
Press the START/STOP button.
To Change Operating Conditions
If you wish to change operating conditions
(Mode, Fan Speed, Thermostat Setting), after
making the timer setting wait until the entire
display reappears, then press the appropriate
buttons to change the operating condition
desired.
To Cancel the Timer
Use the TIMER MODE button to select “CANCEL”.
The air conditioner will return to normal operation.
To Change the Timer Settings
1.
Follow the instructions given in the section
“To Use the ON timer or OFF timer” to select
the timer setting you wish to change.
2. Press the TIMER MODE button to select
either OFF ON or OFF ON.
To Stop Air Conditioner Operation while
the Timer is Operating
Press the START/STOP button.
To Change Operating Conditions
If you wish to change operating conditions
(Mode, Fan Speed, Thermostat Setting), after
making the timer setting wait until the entire
display reappears, then press the appropriate
buttons to change the operating condition
desired.
To Use the Program timer
1
Press the START/STOP button [Fig. 6 (6-9)].
(if the unit is already operating, proceed to step 2).
The indoor unit’s OPERATION Indicator Lamp (green) [Fig. 4 (4-1)] will light.
2
Set the desired times for OFF timer and ON timer.
See the section “To Use the ON timer or OFF timer” to set the desired mode
and times.
After 3 seconds, the display will return to the original state.
The indoor unit’s TIMER Indicator Lamp (orange) [Fig. 4 (4-2)] will light.
3
Press the TIMER MODE button [Fig. 6 (6-5)] to select the
Program Timer operation (OFF ON or OFF ON will display).
The display will alternately show “OFF timer” and “ON timer”, then change to
show the time setting for the operation to occur fi rst.
● The program timer will begin operation. (If the ON timer has been selected
to operate fi rst, the unit will stop operating at this point.)
After 5 seconds, the display will return to the original state.
About the Program timer
● The program timer allows you to integrate OFF timer and ON timer operations in a
single sequence. The sequence can involve one transition from OFF timer to ON timer,
or from ON timer to OFF timer, within a twenty-four hour period.
● The fi rst timer function to operate will be the one set nearest to the current time.
The order of operation is indicated by the arrow in the Remote Controller Display
(OFF  ON, or OFF  ON).
● One example of Program timer use may be to have the air conditioner automatically
stop (OFF timer) after you go to sleep, then start (ON timer) automatically in the morn-
ing before you wake up.
9385989320-02_OM_EN.indd 89385989320-02_OM_EN.indd 8 19-Jul-19 15:04:3819-Jul-19 15:04:38