ScanPartner 620C Image Scanner User's Manual (Doc. No. 250-0062-0 Ver. 1.
FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communication.
Table of Contents 1. INTRODUCTION ........................................................................................... 1-1 2. INSTALLATION ............................................................................................ 2-1 2.1 SHIPPING BRACKET ...................................................................................................2-1 2.1.1 REMOVING THE SHIPPING BRACKET.............................................................2-1 2.1.2 REFITTING THE SHIPPING BRACKET ........
1. INTRODUCTION Congratulations on your purchase of Fujitsu ScanPartner 620C Scanner. Before you install and operate the new Scanner, please take a few minutes to read through this manual. It provides you with the proper instructions on how to unpack, install, operate and maintain the Scanner. Figure 1-1 shows how the Scanner is packed. You can check all items against your “checklist”, included with your Scanner.
2. INSTALLATION Please unpack the Scanner carefully, and check the contents against the checklist. If any items are missing or damaged, please contact your authorized local dealer immediately. Precautions • Keep the Scanner out of direct sunlight. Direct exposure to the sun or excessive heat may cause damage to the unit. • Do not install the Scanner in a humid or dusty place. • Be sure to use the proper AC power source. • Place the Scanner securely on an even, flat surface.
“Shipping Position” Figure 2-1 Removing the Shipping Bracket “Use Position” Figure 2-2 Securing the Shipping Bracket 2-2
2.1.2 REFITTING THE SHIPPING BRACKET Whenever you need to move the Scanner to a new location it is advisable to refit the shipping bracket to avoid causing damage to the Scanners’ internal mechanism. Please follow the instructions below to refit the shipping bracket. i). Turn off the Scanner power at the power on/off switch. ii). Open the document cover. iii). Turn off the Scanner. Note: For steps (iv) to (vi) please refer to Figure 2-1 and 2-2. iv).
SCSI ID Selector On Off SCSI Termination Switch Figure 2-3 Adjusting the SCSI ID setting.
2.3 ADF PAPER CHUTE i). Raise the right side of the paper chute to about 45 degrees. ii). Pull down the wire leg from under the paper chute. iii). Insert the wire leg into the grips on the document cover. iv). Pull out the paper chute extension to the length you want.
2.4 ADF OUTPUT TRAY i). Hold the output paper tray some 30 degrees aslant as shown in Figure 2-5. ii). Insert the three protrusions on the output paper tray to the three slots on the ADF. iii). Release the paper tray gently. Make sure the tray is firmly attached to the ADF. iv). Pull out the output paper tray extension wire to the desired length.
2.5 DOCUMENT LOADING For flatbed scanning Documents that can not be scanned using the ADF can be placed on the flatbed for scanning. (See Figure 2-6) i). Place the document to be scanned onto the document glass face down. ii). Position the document so that the upper-right corner is aligned with the reference mark.
2.6 ADF SCANNING Standard paper size can be scanned automatically using the ADF. Refer to Figure 2-7. i). To prevent occasional paper jam when automatically feeding multiple documents, fan the paper before loading. ii). Lift the balance wire and place the documents to be scanned onto the ADF paper chute face down, with the leading edge in the auto feeder entrance. Let the balance wire rest on the top of the documents. iii).
2.7 CONNECTING THE CABLE i). Turning the Power Off Depress the side marked “O” to turn the power off. Connect the power cable and SCSI signal cable as shown in Figure 2-8 and Figure 2-9. ii). Turning the Power On Depress the side marked “I” to turn the power on. The POWER LED will light. If not, please check the power source. iii). SCSI Termination The Fujitsu ScanPartner 620C comes complete with a built in SCSI terminator.
Power Switch SCSI Port Power Cable Figure 2-8 ScanPartner 620C Power Cable Connection SCSI Cable Connector To PC SCSI Port Figure 2-9 ScanPartner 620C SCSI Cable Connection 2-10
3. MAINTENANCE 3.1 CLEANING THE ADF Your Scanner is designed to be maintenance free. However, it still needs to be cleaned occasionally to ensure optimum image quality and performance. From time to time the pad assembly and feeding rollers may become contaminated with ink, toner particles or paper dust. In this case the scanner may not feed documents smoothly or several documents may feed at once. If this occurs please follow the cleaning procedures to return your Scanner to its original state.
ADF Pad Module Feeding Roller ¬ Figure 3-1 Opening the ADF unit and Document Cover 3-2
3.2 CLEANING THE GLASS The procedures: i). Soak a cotton swab with some isoprophy alcohol (95%). ii). Open the ADF unit and document cover as shown in Figure 6-2. Wipe the glass of flatbed area and ADF area by moving the swab from side to side. iii). Close the ADF unit and document cover. Your Scanner is now ready for use.
3.3 REPLACING THE ADF SNAP-IN PAD MODULE After scanning approximately 150,000 pages through the ADF, the pad spring may be worn out and you may experience problems with document feeding. In this case, it is highly recommended to replace the pad module with a new one. For ordering the pad module, please consult your nearest dealer and follow the procedure below to replace it. Disassembling Procedure 1. Open the ADF front cover by depressing the ADF release button. 2.
Assembling Procedure 1. Take out the ADF pad module from the box. 2. Hold the upper part of the pad clamp and place it gently to the pad holder as shown in Figure 3-4.
4. TROUBLESHOOTING The Scanner will automatically perform a simple self-test each time it is turned on. This will help spot major system errors in the Scanner itself. When the test is initiated, the READY LED is flashing. When the test is completed, if no error occur, the READY LED is steadily on. If you have problems with the operation of your Scanner, please check the following troubleshooting hints. 4.
Question: Paper becomes skewed in the Scanner. Answer: a) Check the feeding roller condition; do the cleaning if necessary. (See Section 3.1) b) Use the paper guide when feeding the paper. Question: When I power on the Scanner, it makes noises and will not stand ready. Answer: There are two possibilities: a) You forgot to remove the shipping retainer from the Scanner. Please remove the shipping retainer first. b) You did not place the Scanner on a flat desktop surface.
Question: While scanning, the Scanner often makes noises, or it scans back and forth. Answer: Please choose lower speed from the TWAIN user interface for low speed PC. Question: The scanned image always comes out to be too dark. Answer: a) Use your application to modify the Gamma setting to 2.2 and 1.8 for your printer and monitor respectively. b) Use Brightness setting from the TWAIN user interface to get a brighter image.
ADF Unit ADF Paper Chute Document Figure 4-2 ADF Paper Jam - Removing the Paper 4-4
5. SPECIFICATIONS All specifications are subject to change without notice. The following can not be properly fed by ADF: • Paper with clip or staple attached; • Paper with ink not totally dry; • Paper with inconsistent thickness, such as envelopes; • Paper with wrinkles, curls, folds or tears; • Tracing paper; • Coated paper; • Carbonless paper; • Paper narrower than 3.5" or wider than 8.
5.1 SCANPARTNER 620C SPECIFICATIONS v 1-pass colour v Flatbed with ADF built-in v 36-bit colour v 12-bit Grey Scale v Line Art/Halftone v Error Diffusion (single bit) Optical Resolution v 600 x 1200 dpi in a dpi increments Light Source v Cold Cathode fluorescent lamp ADF Capacity v 50 pages ADF Scanning Speed v 20 PPM (200dpi, B/W mode, ADF) Scanning Document Size Max. v ADF mode 8.5” x 14” v Flatbed mode 8.5” x 11.
Index A P ADF cover · 4-3 paper chute · 2-5 ADF Scanning · 2-8 paper chute extension · 2-5 paper jam · 2-8, 4-3 POWER LED · 2-9 B protrusions · 2-6 balance wire · 2-8 R C READY LED · 4-1 Cleaning the ADF · 3-1 reference mark · 2-7 Cleaning the Glass · 3-3 refit the shipping bracket · 2-3 Connecting the Cable · 2-9 S D Scanner packing · 1-2 document cover · 2-5 SCSI chain · 2-3 Document Loading · 2-7 SCSI ID selector · 2-3 SCSI Termination · 2-9 O shipping bracket · 2-1 shipping position · 2
