OPERATING MANUAL MODE D’EMPLOI MANUAL DE FUNCIONAMIENTO AIR CONDITIONER Español Français English CEILING SUSPENSION TYPE KEEP THIS MANUAL FOR FUTURE REFERENCE FUJITSU GENERAL LIMITED 9362292047_OM_cover1.
CONTENTS SAFETY PRECAUTIONS ....................................... 1 FEATURES AND FUNCTIONS .............................. 2 NAME OF PARTS ................................................... 3 PREPARATION ....................................................... 5 OPERATION ........................................................... 6 TIMER OPERATION ............................................... 8 SLEEP TIMER OPERATION ................................... 9 ADJUSTING THE DIRECTION OF AIR CIRCULATION .......
FEATURES AND FUNCTIONS AUTOMATIC OPERATION ● COOLING MODEL Merely press the START/STOP button, and the unit will begin automatic operation in the Cooling or Dry mode as appropriate, in accordance with the thermostat setting and the actual temperature of the room.
NAME OF PARTS Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). Fig. 1 1 9 7 6 5 4 0 MANUAL AUTO SWING SWING TIMER OPERATION 3 8 Fig. 2 Electrical Breaker This breaker is installed during the electrical installation. Fig. 3 Fig. 4 Fig. 6 Fig. 5 En-3 9362292047_OM_en.
Fig. 1 Indoor Unit Fig. 4 Remote Control Unit 1 2 3 4 5 6 A B C D E F G H Operating Control Panel (Fig. 2) MANUAL AUTO button Remote Control Signal Receiver OPERATION Indicator Lamp (red) TIMER Indicator Lamp (green) SWING Indicator Lamp (orange) (HORIZONTAL SWING) 7 SWING Indicator Lamp (orange) (VERTICAL SWING) ● If the TIMER indicator lamp flashes when the timer is operating, it indicates that a fault has occurred with the timer setting (See page 16 Auto Restart).
PREPARATION Load Batteries (R03/LR03/AAA × 2) 1 CAUTION! Press and slide the battery compartment lid on the reverse side to open it. Slide in the direction of the arrow while pressing the 2 Insert batteries. 3 Close the battery compartment lid. Be sure to align the battery polarities ( mark. ) correctly. Never mix new and used batteries, or batteries of different types. Batteries should last about one year under normal use.
OPERATION Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). To Select Mode Operation 1 Press the START/STOP button. 2 Press the MASTER CONTROL button to select the desired mode. The indoor unit’s OPERATION indicator lamp (red) will light. The air conditioner will start operating. Each time the button is pressed, the mode will change in the following order. sAUTO s COOL s DRY *HEATt FANt About three seconds later, the entire display will reappear.
OPERATION Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). About Mode Operation AUTO: COOLING MODEL ● When the room temperature is 4 °F higher than the set temperature, the mode will switch between Cooling and Drying. ● During the Drying mode operation, the FAN setting should be switched to LOW for a gently cooling effect during which the fan may temporarily stop rotating.
TIMER OPERATION Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). Before using the timer function, be sure that the remote control unit is set to the correct current time (See page 5). To Use the ON timer or OFF timer 1 Press the START/STOP button (if the unit is already operating, proceed to step 2). TIMER ON OFF PM The indoor unit’s OPERATION indicator lamp (red) will light. 2 Press the TIMER button to select the OFF timer or ON timer operation.
TIMER OPERATION About the PROGRAM timer About the ON timer ● The PROGRAM timer allows you to integrate OFF timer and ON timer operations in a single sequence. The sequence can involve one transition from OFF timer to ON timer, or from ON timer to OFF timer, within a twentyfour hour period.
ADJUSTING THE DIRECTION OF AIR CIRCULATION Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). Vertical (up-down) direction of airflow is adjusted by pressing the remote control unit’s AIR FLOW DIRECTION VERTICAL SET button. Horizontal (right-left) direction of airflow is adjusted by pressing the remote control unit’s AIR FLOW DIRECTION HORIZONTAL SET button.
SWING OPERATION Begin air conditioner operation before performing this procedure. To select Vertical airflow SWING Operation Press the AIR FLOW DIRECTION VERTICAL SWING button. The SWING indicator lamp (VERTICAL SWING) (orange) will light. In this mode, the UP/DOWN air direction flap will swing automatically to direct the air flow both up and down. To Stop Vertical airflow SWING Operation Press the AIR FLOW DIRECTION VERTICAL SWING button once again. The SWING indicator lamp (VERTICAL SWING) will go out.
MANUAL AUTO OPERATION Use the MANUAL AUTO operation in the event the remote control unit is lost or otherwise unavailable. How To Use the Main Unit Controls Press the MANUAL AUTO button on the main unit operating control panel. To stop operation, press the MANUAL AUTO button once again. CAUTION! Do not press the MANUAL AUTO button with wet hands or pointed objects, otherwise an electric shock or malfunction may occur.
SELECTING THE REMOTE CONTROL UNIT SIGNAL CODE When two or more air conditioners are installed in a room and the remote control unit is operating an air conditioner other than the one you wish to set, change the signal code of the remote control unit to operate only the air conditioner you wish to set (four selections possible). When two or more air conditioners are installed in a room, please contact your retailer to set the individual air conditioner signal codes.
TROUBLESHOOTING Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). WARNING! In the event of a malfunction (burning smell, etc.), immediately stop operation, turn off the electrical breaker, and consult authorized service personnel. Merely turning off the unit’s power switch will not completely disconnect the unit from the power source. Always be sure to turn off the electrical breaker to ensure that power is completely off.
TROUBLESHOOTING Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).
OPERATING TIPS AUTO Restart In Event of Power Interruption ● Should the power supply to the air conditioner be interrupted by a power failure, the air conditioner will restart automatically in the previously selected mode once the power is restored. ● Should a power failure occur during TIMER operation, the timer will be reset and the unit will begin (or stop) operating under the new timer setting. In this event, the TIMER indicator lamp (green) will flash (see page. 4).
