User's Manual

60
Settings
■
Radio interference with wireless LANs
Wireless LANs (IEEE802.11b/g) use the same frequency band (2.4
GHz) as the Bluetooth function. For this reason, using the Bluetooth
LAN function of your FOMA terminal at the same time as the wireless
function may cause radio interference, drop in communications speed,
noise, or failed connections.
Also, even when only the Bluetooth LAN function of your FOMA t
erminal
is used, the same phenomena will occur if a Bluetooth function-installed
device is used nearby
. If this happens, perform the following measures:
1. Keep your FOMA terminal at least 10 m away from the Bluetooth
function-installed device.
2. Turn the Bluetooth function-installed device off if it is within 10 m of
your FOMA terminal.
Turning the Bluetooth function on to enable
detection of your
FOMA
terminal
1
→
"Settings"
→
"Wireless controls"
2
Select the "Bluetooth" checkbox
3
Tap "Bluetooth settings" and select the
"Discoverable" checkbox
Your FOMA terminal can be detected for approximately 120 seconds
from other Bluetooth devices.
●
When your FOMA terminal is detected by another Bluetooth
device and receives the pair setting request, either tap "Pair" or
advance to step 4 of "Setting pairs with other Bl
uetooth devices".
Note
●
Packet communications is available even with the Bluetooth
function enabled.
●
When you are not connecting by Bluetooth communications,
disable the Bluetooth function to prevent battery wear.
●
The Bluetooth function enabled/disabled setting is held even when
your FOMA terminal is turned off.
●
The Bluetooth function cannot be used while your FOMA terminal
is turned off.
Renaming your FOMA terminal
You can change the name of your FOMA terminal that is displayed on
other Bluetooth devices.
●
Enable the Bluetooth function in advance.
1
→
"Settings"
→
"Wireless controls"
→
"Bluetooth
settings"
2
Tap "Device name"
3
Enter the new name, and tap "OK"
Setting pairs with other Bluetooth devices
You can connect your FOMA terminal to Bluetooth headphones and talk
handsfree by setting your FOMA terminal as a pair with other Bluetooth
devices.
Once you have set your FOMA terminal as a pair with a Bluetooth
device, the pair setting is stored in me
mory.
●
To do this, enable the Bluetooth function in advance and make sure
that the Bluetooth your FOMA terminal is to be paired with can be
detected.
1
→
"Settings"
→
"Wireless controls"
→
"Bluetooth
settings"
2
Tap "Scan for devices"
Detected Bluetooth devices are displayed in the Bluetooth terminal
list.
3
Tap the Bluetooth device you want to connect to
4
If necessary, enter the pass code (PIN), and tap
"OK"
The pair setting and connection status are displayed under the
name of the Bluetooth device in the Bluetooth device list.
61
Settings
Connecting to a paired Bluetooth device
1
→
"Settings"
→
"Wireless controls"
→
"Bluetooth
settings"
2
In the Bluetooth terminal list, tap the device you
want to connect to
Note
●
To connect to an unpaired device, tap on the device in the
Bluetooth terminal list for one second or more, and tap "Pair &
connect".
Sending files by Bluetooth communications
The following describes an example of the operation to send an image
in the media folder by Bluetooth communications.
●
First set the recipient's FOMA terminal so that is can be detected.
1
Open the media folder, and tap the image you want
to send for one second or more
●
For details on the media folder, see P. 93.
2
"Share"
→
"Bluetooth"
●
If the Bluetooth function is disabled, tap "Turn on".
3
In the Bluetooth terminal list, tap the recipient's
FOMA terminal
When is displayed on the status bar, open the notification panel
and check that transmission is completed.
Receiving files by Bluetooth communications
1
Enable detection of your FOMA terminal
will be displayed on the status bar.
2
Open the notification panel, and tap "Bluetooth
share: Incoming file"
3
Tap "Accept"
When is displayed on the status bar, open the notification panel
and check that reception is completed.
Disconnecting a Bluetooth device
1
→
"Settings"
→
"Wireless controls"
→
"Bluetooth
settings"
2
In the Bluetooth terminal list, tap a connected
device
3
Tap "OK"
Unpairing a Bluetooth device
1
→
"Settings"
→
"Wireless controls"
→
"Bluetooth
settings"
2
In the Bluetooth terminal list, tap a paired device for
one second or more
3
Tap "Unpair" or "Disconnect & unpair"