User's Manual

44
Call/Network Services
Entering touch-tone signals (DTMF tones)
This feature is used for services such as listening to calls on your home
answering machine, ticket reservations and bank balance inquiries.
1
→
"Phone"
2
Enter the phone number, tap " " for one second or
more, and enter a pause (,)
3
Enter the message (touch-tone signal) to send
●
Enter "0" to "9", "*" and "#".
●
When sending multiple messages, separate each message with a
pause (,) delimiter.
4
Tap "SEND"
Note
●
For details on sending touch-tone signals during a call, see
"Operations during calls in progress" (P. 43).
Showing/hiding caller ID at each call
[186/184]
You can specify whether or not to show your telephone number (caller
ID) on the other party's telephone when you make a call.
●
Your caller ID is important personal information. So, take care when
notifying people about it.
1
→
"Phone"
2
Enter the phone number of the other party
3
M→
"Hide My ID" (Add 184)/"Show My ID" (Add
186)
4
Tap "SEND"
Note
●
Show/hide caller ID can be batch set in "Caller ID Notification
Service" (P. 52).
Making an international call
[WORLD CALL]
●
For details on use overseas, see "Overseas Use" (P. 120).
For details on unclear points about WORLD CALL, contact the
"docomo Information Center" on the last page of this manual.
1
→
"Phone"
2
Add "+" (tap "0" for one second or more), enter
country code, area code (city code) and the other
party's phone number
●
If the area code (city code) begins with "0", omit the "0". However,
"0" must be included when making a call to some countries or
regions such as Italy.
●
When selecting from the country list and entering "+ country
code", enter the area code (city code) and the telephone number,
and select
M→
"Add Country code".
3
Tap "SEND"
Note
●
Country codes can be registered by tapping
→
"Phone"
→mM
→
"Country code setting".
45
Call/Network Services
Receiving calls
1
You have an incoming call
2
Tap or press
D
●
To reject incoming calls, either tap or press
M
for one
second or more.
●
If you had a call in the sleep mode or while key operations or the
screen were locked, slide
to the right end to answer the call.
To reject the call, slide
to the left end.
3
When you have finished the call, tap "End" or press
M
Note
●
On this FOMA terminal, calls cannot be put on hold.
●
If your face, or something, comes close to the proximity sensor
during a call, the display goes out, it is redisplayed by moving
away from the sensor.
■
To temporarily mute the ringtone during an incoming call
During an incoming call, press
E
or
F
.
Operations during calls in progress
The following operations are possible in the call in progress screen.
①
Temporarily puts the call on hold*
1
*
2
②
Name or telephone number
③
Ends the call
④
Calls another party*
2
⑤
Turns the Bluetooth head set on*
1
Switches to hands-free talking using
the Bluetooth head set.
⑥
Call time
⑦
Displays the dial pad*
1
Sends touch-tone signals (DTMF
tones).
⑧
Turns the MIC off (mute)*
1
Makes your voice inaudible to the
other party.
⑨
Turns the speaker phone on*
1
Makes the other party's voice audible
from the speaker.
*1 Tapping again restores the screen to
the previous state.
*2 Catch Phone (P. 50) must be
subscribed to.
Note
●
Grayed out items are unavailable.
Adjusting the in-call volume
[In-call volume]
1
During a call in progress, press
E
(increase
volume) or
F
(decrease volume)
Note
●
The in-call volume can be adjusted only during a call in progress
and not at other times.
③
①
④
⑤
②
⑦
⑧
⑨
⑥
Call in progress screen