User's Manual

FUNC TION OPERA T ION A ND DES C R IPT ION（T he following description is without
voice prompt.）
S c an R esumed Mode（S C -REV ）——Menu No.18
1. In frequency or channel mode, press Menu+18, the LC D displays:
2. Press key Menu, and then press key ▲ or ▼ to choose，the L C D displays:
There are three ways of sc anning .
TO：T ime scanning，continue to sc an after searching sig nal for 5 s.
C O：C arrier scanning ，when it searches the signal, it continues to sc an after the signal disappears.
S E：S earch sc anning ，stop scanning once searching the signal.
3. After setting, press key Menu to confirm, and then press key PT T or Exit to standby.
This func tion can scan activities from other radios’ frequencies or c hannels. Y ou can selec t the scan
mode acc ording to your request.
T he op eration s tep s are as f ollows :
!
NOTE
S elec t“ off” in
normal use to
avoid affecting
the radio.
ʎ
PTT ID（PT T-ID）——Menu No.19
1. In frequency or channel mode, press Menu+19, the LC D displays:
2. Press key Menu, and then press key ▲ or ▼ to choose, the LC D displays:
There are four kinds of mode：
OFF：not send.
BOT ：Press PTT key to send code.(T he PT T-ID is set by software)
EOT ：R elease PT T key to send code.
BOT H：Press or release PT T key to send code.
3. After setting, press key Menu to confirm, and then press key PT T or Exit to standby.
This funcition can set the sound of sending PT T-ID when you press key PT T or release it.
T he op eration s tep s are as f ollows :
FUNC TION OPERA T ION A ND DES C R IPT ION（T he following description is without
voice prompt.）
DTMFS T （DT MFS T ）——Menu No.16
This function is that when the radio transmits, the recipient c an hear the DT MF and A NI-ID code issued
by the radio.
!
NOTE
Do not use this func tion if not neces sary in case to af fec t the radio.
ʎ
S ignal C ode（S -C ODE）——Menu No.17
1. In frequency or channel mode, press Menu+17, the LC D displays:
2. Press key Menu, and then press key ▲ or ▼ to choose，the LC D displays:
3. After setting, press key Menu to confirm, and then press key PT T or Exit to standby.
This function is to set radio signal code, it can set 1-15 g roups. T his function can just be set by
prog ram software.
T he op eration s tep s are as f ollows :
1. In frequency or channel mode, press Menu+16, the LC D displays:
2. Press key Menu and then press key ▲ or ▼ to choose, the LC D displays:
C hoose mode: OF F： OFF
DT -S T ：When transmitting , manually press keypads to make DT MF sound.
A NI-S T ：When transmitting, it automatically makes DT MF sound.
DT +A NI：W hen transmitting , manually press keypads or automatically makes DTMF sound.
3. After setting, press key Menu to confirm, then press PT T or E xit to standby.
T he op eration s tep s are as f ollows :
!
NOTE
S elec t“ OFF” when using in case to af fec t the radio.
ʎ
16
DTMFST
OFF
16
DTMFST
DT-ST
17
S-CODE
1
17
S-CODE
13
SC-REV
T0
18
SC-REV
SE
18
PTT-ID
OFF
19
PTT-ID
BOT
19
31 32