User Manual

ManualsBrandsFuji Spray ManualsPaint ApplicationFuji 2804-T75G Mini-Mite 4 PLATINUM - T75G Gravity HVLP Spray System

Limited 2 Year Warranty

Fuji Industrial Spray Equipment Ltd. issues a 24

month limited warranty to the purchaser effective from

the date of purchase against defects in materials or

workmanship. This warranty does not cover abuse,

accidental damage, misuse, normal wear parts, motor

brush replacement, or spray gun maintenance and

clean-up. Warranty is void if repairs are made or

attempted by unauthorized persons. At our option,

Fuji Spray will repair or replace defective parts

without charge provided the purchaser return parts

prepaid to the nearest authorized service center or to

the factory.

Factory returns must first receive a Return Material

Authorization. In North America, please call 800-

650-0930 to obtain an authorization number. In other

countries, please call the company where you pur-

chased the product.

This unit is designed to be used for spray painting and

similar operations only. Fuji Spray will not be held

liable if equipment is not used solely for the purpose it

was designed. Warranty will become void through

improper installation or operation. Any modifications

to the equipment or deviations from recommended

procedures, accidental damage or any related action

that impairs or abuses normal wear and care of Fuji

Spray equipment will also void warranty and liability.

CONTENTS

Contents . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety Precautions . . . . . . . . . . . . . . . . 2

Getting Started. . . . . . . . . . . . . . . . . . . . . 3

Spray Pattern . . . . . . . . . . . . . . . . . . . . . . 4

Spraying Technique . . . . . . . . . . . . . 5

Aircap Selection . . . . . . . . . . . . . . . . . . . 6

Viscosity Guide . . . . . . . . . . . . . . . . . . . . 7

Latex Paint . . . . . . . . . . . . . . . . . . . . . . . . 8

General Cleaning . . . . . . . . . . . . . . . . . . . . 9

Cleaning Fluid Passages . . . . . . . . . . . 10

Turbine Problems . . . . . . . . . . . . . . . . . 10

Finish Problems . . . . . . . . . . . . . . . . . .11

Filter Replacement. . . . . . . . . . . . . . . .11

Spray Gun Problems . . . . . . . . . . . . . 12-14

Needle Packing Nut . . . . . . . . . . . . . . . 14

Parts Diagrams. . . . . . . . . . . . . . . . . 15 -18

Service Information. . . . . . . . . . . . . . . . 19

Warranty Information . . . . . . . . . . . . . . 20

CE Declaration . . . . . . . . . . . Back Cover

Summary of content (10 pages)

PAGE 1
Limited 2 Year Warranty Fuji Industrial Spray Equipment Ltd. issues a 24 month limited warranty to the purchaser effective from the date of purchase against defects in materials or workmanship. This warranty does not cover abuse, accidental damage, misuse, normal wear parts, motor brush replacement, or spray gun maintenance and clean-up. Warranty is void if repairs are made or attempted by unauthorized persons.
PAGE 2
Please read these instructions carefully before using the equipment For SERVICE & PARTS GROUNDING INSTRUCTIONS This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug.
PAGE 3
GUN HOLDER & FILLING STATION GETTING STARTED Please register your Fuji Spray Product at www.fujispray.com/product-registration NOTE: Throughout this Manual we have used the generic word ‘Paint’ to describe all and any coatings. Please substitute the word ‘Paint’ for whatever finish or coating you are spraying. Your Fuji Spray Gun has been adjusted at the factory and is ready for spraying.
PAGE 4
CHANGING THE SHAPE OF THE FAN A) Loosen the Collar 5201. Turn the Air Cap 5202 to the horizontal position then re-tighten the Collar to lock it into place. This setting produces a vertical spray pattern. This pattern is used more than any other by experienced spray painters. B) Setting the Air Cap in a vertical position produces a horizontal spray pattern. To lock it in position, tighten the Collar. The horizontal fan pattern is the most useful for painting vertically such as a doorframe.
PAGE 5
FUJI T-70 & T-75G SPRAY GUN ACTUAL SPRAYING TECHNIQUES. The Spray Gun should be held perpendicular to the surface at all times. HOLD THE GUN NO MORE THAN 8” (20cm) AWAY FROM THE SURFACE TO BE PAINTED. CORRECT METHOD Start off the piece. Pull the Trigger and move the Spray Gun in the direction you want to spray. Continue off the edge of the piece on the other end before releasing the Trigger. Between each successive pass, overlap by about a half.
PAGE 6
AIR CAP SET SELECTION Six additional size Setups are available as accessories. Size No.3 (1.3mm) is standard with all Fuji T-Spray Guns. 1.0mm, 1.3mm or 1.5mm can be used for any type of fine-finishing application. The larger sizes such as 1.5mm allow for more fluid output - desirable with fast drying lacquers. AIR CAP SET - Part 5100 Series If you do not intend on spraying walls & ceilings the only additional Setups you need would be the 1.0mm, 1.5mm, and 1.8mm. No. 1 (Part 5100-1) .8mm (.
PAGE 7
LEAKAGE FROM THE NOZZLE VISCOSITY GUIDE This occurs when the Needle Packing Nut 5210 is too tight compressing the Needle Packing 5209 too tightly around the Needle. A Viscosity Cup (Ford #4 Standard) is included with your Fuji System. Half fill the cup with water. Attach the Gun to the Hose and turn on the Turbine blower to pressurize the Cup. Pull the Trigger and release. Check the Nozzle for water spurting out. Use the supplied wrench to GENTLY loosen the Nut (1 or 2 degrees only at a time).
PAGE 8
THE TRIGGER IS SLUGGISH A WORD ABOUT LATEX Although Latex Paint was never originally intended to be sprayed, a professional finish can be achieved by following a few simple rules. (Please do not confuse Latex with the newer water-based coatings). For work such as cabinetry or trim, our equipment can be used successfully with Latex Paint. The Latex will have to be thinned with WATER - approximately 10-30% depending on the brand of paint.
PAGE 9
SPRAYGUN PROBLEMS GENERAL CLEANING NO PAINT (OR VERY LITTLE PAINT) To clean the Gun after each use, empty all paint from the Cup. Use a solvent-soaked rag to clean the residue in the Cup. Then, spray some clean solvent through the Gun into a clean rag (to avoid filling the room with unnecessary spray) or a bucket. Repeat until the inside of the fluid passages in the Gun, Metal Fluid Tube etc. are clean. Use the wet rag to wipe off the Air Cap and tip of the Fluid Nozzle.
PAGE 10
CLEANING FLUID PASSAGES FINISH PROBLEMS To clean, flush solvent through the Spray Gun while the paint is still wet inside the Gun. If this type of quick cleaning is performed frequently, the Spray Gun will function well for many years. 99% of problems with a Spray Gun stem from clogs in the fluid passages and (perhaps more important), the Pressure Tube air passages. Please see Page 12... No Paint (or very little paint).