User Manual - M-Model Cover.
Fuji Limited 2 Year Warranty Fuji Industrial Spray Equipment Ltd. (“Fuji”) provides a 24 month limited warranty on the product to the original purchaser effective from the date of purchase against defects in materials and workmanship.
Please read these instructions carefully before using the equipment For SERVICE & PARTS USA GROUNDING This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug.
GUN HOLDER GUN HOLDER INSTALLATION The 2 holes on the top of the Holder require the Black Machine Screws and Washers. These Screws fit into Threaded Inserts in the Metal Case. Do not overtighten - snug is fine. The single Silver-Colored Screw must be installed to the single hole on the side of the Gun Holder. Once again, please do not overtighten this screw - snug is fine. GUN HOLDER USE Place the Hose Connector 11 (base of the Gun Handle) over the shaft of the Gun Holder shown in above illustration.
· Always wear appropriate gloves and eye protection · Always wear a respirator or mask. Read all instructions of the respirator or mask to ensure that it will provide the necessary protection against the inhalation of harmful vapors. Please also check with the local jurisdiction. · Paint, solvents, insecticides and other materials may be harmful if inhaled. · Store hazardous fluid in approved containers, and dispose of it according to applicable guideline.
;EŽƚ ^ŚŽǁŶͿ &ŝƚƐ ƚŽ hͲdƵďĞ ϰϯ WƵƐŚ ƚŽ ƌĞůĞĂƐĞ WƌĞƐƐƵƌĞ dƵďĞ Please register your Fuji Spray Product at www.fujispray.com/product-registration NOTE: Throughout this Manual we have used the generic word ‘Paint’ to describe all and any coatings. Please substitute the word ‘Paint’ for whatever finish or coating you are spraying.
CHANGING SIZE & SHAPE OF THE PATTERN A) Loosen the Collar #1. Turn the Aircap #2 to the horizontal position. This setting produces a vertical spray pattern. Always make sure the Collar is snug tight. B) Setting the Aircap in a vertical position produces a horizontal spray pattern. To lock it in position, tighten the Collar #1 clockwise until it stops turning. C) For smaller pattern sizes, the Aircap can be set at horizontal or vertical. Turn the Pattern Control Knob #6 (at the rear of the Gun).
FUJI M-MODEL SPRAY GUN SPRAYING TECHNIQUE The spraygun should be held perpendicular to the surface at all times. HOLD THE GUN NO MORE THAN 8” (20cm) AWAY FROM THE SURFACE TO BE PAINTED. But closer is ok. CORRECT METHOD Start moving the spraygun in the direction you want to spray and press the trigger. Between each successive pass, overlap by about a quarter. INCORRECT METHOD Never, for any reason, point the spraygun directly at the face, or head of a person.
AIRCAP SET SELECTION TURBINE CARE AND MAINTENANCE 5 additional setups are available as accessories. Size No.3 is standard with all Fuji M-Sprayguns. No. 2, 3 or No. 4 can be used for any type of fine-finishing application. The larger sizes such as No. 4 allow for more fluid output. This is desirable when spraying fast drying lacquers. It allows you to spray wetter to obtain better leveling. FILTER(S) It is important to clean or replace your filters regularly.
CLEANING FLUID PASSAGES VISCOSITY GUIDE To clean, flush appropriate solvent (refer to material manufacturer's cleaning recommendations) through the Spraygun while the paint is still wet inside the gun. If this type of quick cleaning is performed frequently, the Spray Gun will function well for many years. 99% of problems with a Spray Gun stem from clogs in the fluid passages and (perhaps more important), the Pressure Tube air passages. Please see Page 13... No Paint (or very little paint).
A WORD ABOUT LATEX LEAKAGE FROM THE NOZZLE Although latex paint was never originally intended to be sprayed, a professional finish can be achieved by following a few simple rules. (Please do not confuse latex with the newer water-based coatings). For work such as cabinetry or trim, our equipment can be used successfully with latex paint. The latex will have to be thinned with WATER - approximately 20-30% depending on the brand of paint.
THE TRIGGER IS SLUGGISH • • GENERAL CLEANING The Needle Packing is too tight - see ADJUSTING THE NEEDLE PACKING. Page 15 Bent Needle POOR SPRAY PATTERN • • • • Damaged Needle or Nozzle Nozzle is clogged Air holes in Aircap clogged Gun too far from surface (max.
FINISH PROBLEMS SPRAYGUN PROBLEMS ORANGE PEEL - If the finish is rough and resembles orange peel then the material is too thick. (Or perhaps you have the Air Control Valve turned down - please check that it is fully open). The ‘paint’ will not atomize properly and the surface will be spotty. To remedy this, add more thinner (or appropriate solvent). For fast drying products such as lacquers, you may also want to add a lacquer retarder.
FINISH PROBLEMS SPRAYGUN PROBLEMS ORANGE PEEL - If the finish is rough and resembles orange peel then the material is too thick. (Or perhaps you have the Air Control Valve turned down - please check that it is fully open). The ‘paint’ will not atomize properly and the surface will be spotty. To remedy this, add more thinner (or appropriate solvent). For fast drying products such as lacquers, you may also want to add a lacquer retarder.
THE TRIGGER IS SLUGGISH • • GENERAL CLEANING The Needle Packing is too tight - see ADJUSTING THE NEEDLE PACKING. Page 15 Bent Needle POOR SPRAY PATTERN • • • • Damaged Needle or Nozzle Nozzle is clogged Air holes in Aircap clogged Gun too far from surface (max.
A WORD ABOUT LATEX LEAKAGE FROM THE NOZZLE Although latex paint was never originally intended to be sprayed, a professional finish can be achieved by following a few simple rules. (Please do not confuse latex with the newer water-based coatings). For work such as cabinetry or trim, our equipment can be used successfully with latex paint. The latex will have to be thinned with WATER - approximately 20-30% depending on the brand of paint.
CLEANING FLUID PASSAGES VISCOSITY GUIDE To clean, flush appropriate solvent (refer to material manufacturer's cleaning recommendations) through the Spraygun while the paint is still wet inside the gun. If this type of quick cleaning is performed frequently, the Spray Gun will function well for many years. 99% of problems with a Spray Gun stem from clogs in the fluid passages and (perhaps more important), the Pressure Tube air passages. Please see Page 13... No Paint (or very little paint).
AIRCAP SET SELECTION TURBINE CARE AND MAINTENANCE 5 additional setups are available as accessories. Size No.3 is standard with all Fuji M-Sprayguns. No. 2, 3 or No. 4 can be used for any type of fine-finishing application. The larger sizes such as No. 4 allow for more fluid output. This is desirable when spraying fast drying lacquers. It allows you to spray wetter to obtain better leveling. FILTER(S) It is important to clean or replace your filters regularly.
FUJI M-MODEL SPRAY GUN SPRAYING TECHNIQUE The spraygun should be held perpendicular to the surface at all times. HOLD THE GUN NO MORE THAN 8” (20cm) AWAY FROM THE SURFACE TO BE PAINTED. But closer is ok. CORRECT METHOD Start moving the spraygun in the direction you want to spray and press the trigger. Between each successive pass, overlap by about a quarter. INCORRECT METHOD Never, for any reason, point the spraygun directly at the face, or head of a person.
CHANGING SIZE & SHAPE OF THE PATTERN A) Loosen the Collar #1. Turn the Aircap #2 to the horizontal position. This setting produces a vertical spray pattern. Always make sure the Collar is snug tight. B) Setting the Aircap in a vertical position produces a horizontal spray pattern. To lock it in position, tighten the Collar #1 clockwise until it stops turning. C) For smaller pattern sizes, the Aircap can be set at horizontal or vertical. Turn the Pattern Control Knob #6 (at the rear of the Gun).
;EŽƚ ^ŚŽǁŶͿ &ŝƚƐ ƚŽ hͲdƵďĞ ϰϯ WƵƐŚ ƚŽ ƌĞůĞĂƐĞ WƌĞƐƐƵƌĞ dƵďĞ Please register your Fuji Spray Product at www.fujispray.com/product-registration NOTE: Throughout this Manual we have used the generic word ‘Paint’ to describe all and any coatings. Please substitute the word ‘Paint’ for whatever finish or coating you are spraying.
· Always wear appropriate gloves and eye protection · Always wear a respirator or mask. Read all instructions of the respirator or mask to ensure that it will provide the necessary protection against the inhalation of harmful vapors. Please also check with the local jurisdiction. · Paint, solvents, insecticides and other materials may be harmful if inhaled. · Store hazardous fluid in approved containers, and dispose of it according to applicable guideline.
GUN HOLDER GUN HOLDER INSTALLATION The 2 holes on the top of the Holder require the Black Machine Screws and Washers. These Screws fit into Threaded Inserts in the Metal Case. Do not overtighten - snug is fine. The single Silver-Colored Screw must be installed to the single hole on the side of the Gun Holder. Once again, please do not overtighten this screw - snug is fine. GUN HOLDER USE Place the Hose Connector 11 (base of the Gun Handle) over the shaft of the Gun Holder shown in above illustration.
Fuji Limited 2 Year Warranty Fuji Industrial Spray Equipment Ltd. (“Fuji”) provides a 24 month limited warranty on the product to the original purchaser effective from the date of purchase against defects in materials and workmanship.
FUJI SPRAY® CONNECT WITH US! @FUJISPRAY @FUJISPRAYOFFICIAL @FUJISPRAY NEED HELP? FUJISPRAY.COM SUPPORT@FUJISPRAY.COM +1-800-650-0930 Fuji Industrial Spray Equipment Ltd. 800 Alness Street, Toronto, ON, Canada M3J 2H5 User Manual - M-Model Cover.
