MAX S700 CI+ USER'S MANUAL
MAX S700 CI+ ENGLISH USER'S MANUAL
USER’S MANUAL· MAX S700CI+ CAUTIONR RISK OF ELEKTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to “dangerous voltage” and to prevent from a risk of electric shock. Warning: To reduce the risk of electric shock, don’t open the cabinet. Refer servicing to qualified personnel only. The exclamation point within an equilateral triangle is intended to alert the user to important operating and maintenance (servicing).
USER’S MANUAL· MAX S700CI+ Note: This user’s manual is adapted to the version v.1.114. In order to download the complete user’s guide and get more information about receivers, please visit the website http://receivers.ftemaximal.com. The coaxial cable, with satellite signal, must be connected to the “IF IN” connector. The “TV SCART” or “HDMI” connectors must be connector to the TV set. Depending on the type of installation, the receiver should be connected and configured following next examples.
USER’S MANUAL· MAX S700CI+ Quick setup The receiver includes an installation assistant (Quick Setup) that will help you to setup the different parameters. When the receiver is turned on at first time (using the button at the rear panel of the receiver), the next menu is shown on the TV. NOTE: Basic operation hints display on the sidebar and lower bar. - OK : Press [OK] to enter into the menu or choose the item.
USER’S MANUAL· MAX S700CI+ Antenna and program setup Enter the Guided installation or enter the sub-menu to change the settings manually. Type of tuner installation Select the same way of your tuner and press [OK] to confirm the setting. Satellite list editor - Select satellite: Select the satellite in the satellite list. - Name: Edit the name of the satellite. - Orb.pos[Deg]: Edit the degree of Orb. - West/east : choose west or east. - Press [Red] button to remove the current satellite.
USER’S MANUAL· MAX S700CI+ Transponder list editor - Select satellite position: choose the satellite you are using. - Select transponder: choose the transponder from the list. - Frequency: edit the frequency. - Symbol rate: edit the symbol rate - Modulation: Change the modulation to QPSK, QPSK S2 or 8 PSK - Polarization: Change the polarization to Horizontal or Vertical.
USER’S MANUAL· MAX S700CI+ Main menu - File viewer - Media viewer * - Select picture - Select music - Leave media viewer - Recordings * - Timer programming - Mosaic preview - Stream selection - Subtitle track - Audio track - Digital output - System setup - Language setttings - Time settings - Antenna and program setup - Audio/Video setup - General settings - CI Settings - OSD Setup - Mass-storage utilities - Password and parental settings - Software update - Restore factory settings - Information * This
USER’S MANUAL· MAX S700CI+ Index 1. Panel & remote control description............................................................... 9 1.1. Front panel description ......................................................................................................... 9 1.2. Rear panel description.......................................................................................................... 9 1.3. Remote control description.......................................................................
USER’S MANUAL· MAX S700CI+ 3. Main menu...................................................................................................... 16 3.1. File viewer........................................................................................................................... 16 3.1.1. Play Picture.................................................................................................................. 17 3.1.2. Play music.....................................................................
USER’S MANUAL· MAX S700CI+ 1. Panel & remote control description 1.1. Front panel description 1 2 3 1. POWER: 2. STAND BY LED: 3. LOCK LED: 4. DISPLAY: 5. IR SENSOR: 6. FRONT COVER: 7. BUTTONS: 4 5 6 7 Switches the receiver on, or enters standby mode. To completely switch off the receiver, you have to use the switch on the back of the receiver. Shows if the receiver is in Standby mode Indicates a sufficient signal level at the IF IN input. 4 Digits to display the program numbers.
USER’S MANUAL· MAX S700CI+ 1.3. Remote control description 1. MUTE: 2. AUDIO: 3. TV/STB: 4. SLEEP: Switches audio on and off. Opens audio menu. Without function. Starts the sleep timer to turn off the receiver automatically. Press repeadtedly to change the timer. 5. SUB: Switches subtitle on and off.. 6. MULTI: Without function. 7. P/N: Switches between PAL and NTSC. 8. 0~9: For direct typing values and names 9. PG UP / DN: Moves cursor in block steps 10. SAT: Without function. 11.
USER’S MANUAL· MAX S700CI+ 2. Basic operation on remote control unit. 2.1. Standby Mode 1. Press [Power] button to switch from TV/radio mode to standby mode 2. In standby mode press [Power] button again to switch back to TV/radio mode. The last active channel will be showed. 3. To switch off the STB complete press the main power button. 2.2. Mute 1. Press the [Mute] button to mute the sound. On the screen an icon will be displayed to indicate the muted sound. 2.
USER’S MANUAL· MAX S700CI+ 2.11. FAV In TV mode press the [FAV] button to display the Favorite Group window on the screen as the picture beside shows. In the Favorite Group window you can select the desired favorite channel with [CH▲/▼] and confirm it with [OK] to switch to it. In bigger groups you can navigate with [PGUP/ PGDN]. Press [Exit] to close the Favorite Group window. 2.12.
USER’S MANUAL· MAX S700CI+ 2.15. Channel list In TV mode press [OK] button to open the TV service window. 1. Press the [Red] button to display TV services. Press [▲/▼] button to select TV service and press [OK] to change to your selected service. 2. Press [Green] display Radio services Press [▲/▼] button to select Radio service and press [OK] to change to your selected service. 3.
USER’S MANUAL· MAX S700CI+ 2.19. ZOOM 1. The [Zoom] key allows you to magnify a certain area on the images and the current screen will show 2. Press [Zoom] key again, the image will enlarge rotate as x1, x2, x4, x6, x8, x12, x16. 3. In “x2 ~ x16” image, using [CH▲/▼ / VOL◄/►] keys to move the image center area you want to see. 4. In zoom mode, press [Exit] to close “Zoom” window. 2.20. INFO 1.
USER’S MANUAL· MAX S700CI+ 2. If some services are being recorded, it will show the service name on REC1 and REC2. 2.25. Forward / rewind (◄◄|►►) * When you play a recorded channel, press [◄◄] button to back the program fast and Press [►►] to fast forward the program.Selection: 2x, 4x, 8x, 16×, 64× speed. 2.26. Play / Pause (►II) * When you play a current or recorded program, press [►II] will stop the program, press [►II] again will play the program continually. 2.27.
USER’S MANUAL· MAX S700CI+ 3. Main menu Press [Menu] to enter into the main menu. Press [▲/▼] to select the sub menu, Press [OK] to enter the selected sub-menu. 3.1. File viewer 1. In File viewer menu, all of the connected storage device can be seen. Select the storage device and press [OK] to enter into the device. 2. Press [▲/▼] to select the file. After the file has been selected, press [OK] to play the file, whether it can be played depends on whether the format can be supported by the software.
USER’S MANUAL· MAX S700CI+ 3.1.1. Play Picture 1. Select the specific picture file (jpg, bmp and png format are supported). The dimension and size displays on the top of the preview picture. 2. Press [OK] to open the picture and play the picture in full screen. 3. Press [►II] button to pop up the slideshow scope menu. Press [▲/▼] to select the scope you need and Press [OK] to confirm the selection and start slideshow.
USER’S MANUAL· MAX S700CI+ 3.2.1. Select picture menu Select the picture file and press [OK] to play the picture. 1. 2. 3. 4. 5. 6. 7. 8. Press [INFO] to pop up the operation menu. Press [Blue] button to play the next picture. Press [Yellow] button to play the previous picture. Press [Red] button to start the slideshow. Press [Green] button to play the shuffle on. Press [►►I] button to Zoom in. Press [I◄◄] button to Zoom out. Press [REC] button to rotate. 3.2.2.
USER’S MANUAL· MAX S700CI+ 3.4.1. Edit timer menu, 1. Title: Edit the title. 2. Timer type: Edit timer type (Recording, Switch Service, Power Down). 3. Start date: Edit timer start date. 4. Start time: Edit timer start time. 5. Duration: Edit timer duration. 6. Select the service. 7. Edit timer mode: Single, weekdays, weekly weekends daily. 8. Edit power mode after recording: power on/ standby. 9. Select the device you are going to record to. Press [REC] button to save the settings and exit the menu.
USER’S MANUAL· MAX S700CI+ 3.7.4. Audio/video setup 1. Display format: switch the screen aspect ratio mode. You can select the needed mode from Auto / 4:3 / 16:9 with [◄/►]. 2. Scaling method: You can select pillar/letterbox, fullscreen (zoom), fullscreen (CCO). 3. HDMI signal: Options are 1080i, 720P, 480i, 576i. 4. SDTV standard: Options are PAL, NTSC, SECAM. 5. Scart output You can select CVBS+YPbPr, Y/C to choose scart output 6.
USER’S MANUAL· MAX S700CI+ 3.7.5. CI settings 1. You can see the CI status in this menu, when there is no CI module, it will display “No module” 2. After you insert CI module into the Slot, CI+ matching will start automatically. 3. Then the status will appear to be Module Inserted. Please press [OK] to set the configuration of you CI slot. 4. Pin-Code modification: Set the pin code of the CI module. 5. If there is no Smartcard inserted into the module.
USER’S MANUAL· MAX S700CI+ Then the services and channels that CI+ card supports are available. 6. The language of CI module is available in English and German. 7. The module information. 8. CI+ software download is available. - 22 - MAX S700 CI+ Version 1.
USER’S MANUAL· MAX S700CI+ 3.7.6. OSD setup 1. OSD display time: Enter the OSD display time using numbers or press [◄/►] to increase or decrease. The max display time is 30 seconds. 2. OSD transparency: Press [◄/►] to edit the OSD transparency. 3. OSD color scheme: Press [◄/►] to edit the OSD color scheme (Red, Grey, Blue and Green). 4. Menu window hor. Alignment Select the horizon location of OSD to be left/center/right. 5. Menu window ver.
USER’S MANUAL· MAX S700CI+ 3.7.10. Restore factory settings… When you press [OK] on the “restore factory settings” item: If you press [OK] then all changes you made will be reset to default values. Press [Exit] to abort the restoring. 3.8. Information When you select the “Information” menu you will see a screen like beside. The screen displays information about the current channel. Including satellite, software version, CI slot, service and storage device information.
USER’S MANUAL· MAX S700CI+ 4. Technical Specification VIDEO Decoding Bit rate Output Aspect ratio Active pixel (SCART) Active pixel (HDMI) Output connector MPEG-4 & MPEG-2 & MEPG-1 compatible Max. 90Mbit/s PAL/NTSC 4:3, 16:9, Letterbox 480i/576i 480i / 576i / 720p / 1080i / 1080p HDMI / Scart / RCA AUDIO Decoding Mode Bit rate Output connector MPEG / Dolby Digital / Dolby Digital + Mono / Left / Right / Stereo Max.
USER’S MANUAL· MAX S700CI+ 5. Conformity declaration CONFORMITY DECLARATION “WE , FTE MAXIMAL, DECLARE THAT THE PRODUCT MAX S700 CI+ IS IN CONFORMITY WITH FOLLOWING DIRECTIVES Low Voltage Directive 2006/95/EC EMC Directive 2004/108/EC” If you wish a copy of the conformity declaration, please contact the company - 26 - MAX S700 CI+ Version 1.
ESPAÑA Mogoda, 110 Pol. Industrial Can Salvatella 08210 Barberà del Vallès (Barcelona) España Tel. 00 34 93 729 27 00 Fax. 00 34 93 729 30 73 ftemaximal@ftemaximal.com www.ftemaximal.com FRANCE 16 ZAE Les Mouilles 74570 Groisy Tel. 00 33 450 68 80 17 Fax. 00 33 450 68 84 68 sav@ftemaximal.fr www.ftemaximal.com ITALIA Via Edison, 29 42040 Calerno di Sant’Ilario d’Enza (RE) Tel. 00 39 05 22 90 97 01 Fax. 00 39 05 22 90 97 48 fte@fte.it www.ftemaximal.com DEUTSCHLAND BCN Distribuciones S.A.
