Datasheet

ManualsBrandsFSP FORTRON ManualsPower Supply UnitsIndustrial PC PSU 180 W 80 PLUS

SPECIFICATION

ESD09081969

Released Date:2011/06/23-10:56:20

Summary of content (12 pages)

PAGE 1
SPECIFICATION ESD09081969 Released Date:2011/06/23-10:56:20
PAGE 2
1/11禁止翻印外洩文件資料管制文件資料管制文件資料管制台灣桃園市建國東路 22 號 NO.22,Jianguo E, Rd.,Taoyuan City,Taiwan,R.O.C. TEL:+886-3-375-9888 FAX:+886-3-375-6966 SPECIFICATION FSP180-50LE(STD001) 9PA1803552 Main Feature Active PFC Circuit Full Range Input APR 8, 2010 REV:02 ESD09081969-R9.
PAGE 3
文件資料管制文件資料管制文件資料管制 MODEL: FSP180-50LE Revision History Rev 02 2/11禁止翻印外洩 Description UPDATE Erp DESCRIPTION Date Author 4.8 KARL 2 ESD09081969-R9.
PAGE 4
文件資料管制文件資料管制文件資料管制 1. GENERAL DESCRIPTION AND SCOPE This is the specification of Model FSP180-50LE; AC-line powered switching power supply with active PFC (Power Factor Correction) circuit, meet EN61000-3-2 and with Full Range Input features. Designed and manufactured by FSP GROUP. The 5Vsb power is less than 1Winput at power off mode (PS_ON input at high state) which is comply with EuP Lot 6 year 2010 requirement.
PAGE 5
文件資料管制文件資料管制文件資料管制 3. PHYSICAL REQUIREMENTS 3.1 MECHANICAL SPECIFICATIONS The mechanical drawing of the subject power supply, which indicate the form factor, location of the mounting holes, location, the length of the connectors, and other physical specifications of the subject power supply. Please refer to the attachment drawing. 3.2 CONNECTOR SPECIFICATIONS The power supply connectors are: AC Inlet : Standard inlet socket 10A/250V, UL/CSA/VDE approved.
PAGE 6
文件資料管制文件資料管制文件資料管制 4. ELECTRICAL REQUIREMENTS 4.1 OUTPUT ELECTRICAL REQUIREMENTS The subject power supply will meet all electrical specifications below, over the full operation temperature range and dynamic load regulation. 4.1.1. OUTPUT RATING Output 1 2 3 4 5 Nominal +3.3V +5V +12V -12V +5VSB Regulation ±5% ±5% ±5% ±10% ±5% Ripple/Noise 50mV 50mV 120mV 120mV 50mV Min 0.3A 0.3A 1.5A 0.0 A 0.0 A Max 14.0A 16.0 A 14.0 A 0.5A 2.0A ※ –12V,+3.
PAGE 7
文件資料管制文件資料管制文件資料管制 4.1.4.OUTPUT RISE TIME (10% TO 90% OF FINAL OUTPUT VALUE, @FULL LOAD) 115V-rms or 230V-rms + 5Vdc : 20ms Maximum 4.1.5.OVER VOLTAGE PROTECTION +5Vdc output: +5.7 Vdc minimum, +12Vdc output: +13.3Vdc minimum, + 3.3Vdc output: +3.7Vdc minimum, + 6.5Vdc maximum +15.6Vdc maximum + 4.5Vdc maximum 4.1.6.SHORT CIRCUIT PROTECTION Output short circuit is defined to be a short circuit load of less than 0.1 ohm. In the event of an output short circuit condition on +3.
PAGE 8
文件資料管制文件資料管制文件資料管制 POWER GOOD @ 115/230V,FULL LOAD POWER FAIL @115/230V, FULL LOAD PS_ON 100 –500mSec. 1 mSec. minimum ON OFF P.G. SENSE LEVEL 95% +5V,+3.3V +12V,-12V O/P P.G. T1 < 20mS T1 T2 = 100~500mS T3 > 1mS T2 T3 4.2. OUTPUT TRANSIENT LOAD RESPONSE +5V and +12V must be within specification for a step change in current as specified below. The outputs will be tested one section at a time with all other sections at maximum load. The test transition will be from IA to IB and IB to IA.
PAGE 9
文件資料管制文件資料管制文件資料管制 +3.3Vdc: IA: 14.0 amps IB: 11.0 amps Volts variation: +3.3V +-5% Setting time: 10 ms max Transient load slew rate is 0.1A/μS +5Vsb : -12V : 0.5A 0.1A IA IB 10ms 10ms 4.3. INPUT ELECTRICAL SPECIFICATIONS 4.3.1. VOLTAGE RANGE PARAMETER V-in Range UNITS V-rms 90 - 264 4.3.2. INPUT FREQUENCY INPUT FREQUENCY 47–63Hz 4.3.3. INRUSH CURRENT (Cold start – 25 deg. C) 115V 230V No damage No damage 4.3.4. INPUT LINE CURRENT 8/11禁止翻印外洩 115V 230V 4.0 Amps – rms maximum 2.
PAGE 10
文件資料管制文件資料管制文件資料管制 4.4. EFFICIENCY 115 VAC @Full Load 230 VAC @Full Load 68% minimum 68% minimum 4.5.Standby Power Consumption (5Vsb): Input Power < 1W @ 5Vsb/100mA & 230Vac input PS_ON input signal @ High State 4.6. PS_ ON# PS_ON# is an active-low, TTL-compatible signal that allows a motherboard to remotely control the power supply in conjunction with features such as soft on/off, Wake on LAN+, or wake-on-modem.
PAGE 11
文件資料管制文件資料管制文件資料管制 Operating Storage 85% RH, Non-condensing 95% RH, Non-condensing 5.3. VIBRATION The subject power supplies will withstand the following imposed conditions without experiencing non-recoverable failure or deviation from specified output characteristics. Vibration Operating – Sine wave excited, 0.5 G maximum acceleration, 10-250 Hz swept at one octave / min.
PAGE 12
文件資料管制文件資料管制文件資料管制 The subject power supplies will meet FCC and VFG class B requirements . 7.2. RADIATED EMI The subject power supplies will meet FCC and CISPR 22 requirements . 8. LABELLING Label marking will be permanent, legible and complied with all agency requirements. 8.1. MODEL NUMBER LABEL Labels will be affixed to the sides of the power supply showing the following: - Manufacturer’s name and logo. - Model no., serial no., revision level, location of manufacturer.