iCommand-Touch Manual

CAP-837
1.3 General safety
1. Read and understan
d all the instructions found in
this manual before operating your
compressor.
2.
Disconnect the main power source before
working on or performing any maintenance
procedures on this unit. Use a lock out and tag
out process.
3.
Do not attempt to remove any parts, break any
connection, loosen oil fill plug or drain plug unt
unit has been shut down and air pressure has been
relieved.
4.
Do not operate the compressor in excess of its
rated pressures and speeds indicated on the com
pressor nameplate.
5.
Do not remove guards, shields, or screens while
the compressor is in
operation. If removed for
maintenance replace before resuming operation.
6.
Observe the delivery pressure gauge daily to be
sure the automatic control system is operating
within proper limits.
7.
Periodically check all safety and relief devices for
proper operation.
8.
Use compressed air properly. Pressurized air can
cause serious injury to personnel.
9.
Be sure that no tools, rags or loose parts are left
in or on the compressor or drive parts.
10.
Do not use flammable solvents for cleaning
parts.
11. Exerc
ise cleanliness during maintenance and
when making repairs. Keep dirt away from parts and
exposed openings by covering with clean cloth or
Kraft paper.
12. Do not install a shut-
off valve in the discharge
line without installing a pressure relief valve
between the shut-
off and the compressor package.
13.
Do not operate the compressor in areas where
there is a possibility of flammable or toxic
substances entering the system.
14.
Never disconnect (or jump) the air discharge
temperature switch or any other
safety device and
attempt to operate the compressor.
15. Know what mode of operation the compressor is
in before working around the unit. The power may
be on but the machine not running if it is in the auto
restart
mode. Adhere to note #2 above.
7
d all the instructions found in
compressor.
Disconnect the main power source before
working on or performing any maintenance
procedures on this unit. Use a lock out and tag
Do not attempt to remove any parts, break any
connection, loosen oil fill plug or drain plug unt
il the
unit has been shut down and air pressure has been
Do not operate the compressor in excess of its
rated pressures and speeds indicated on the com
-
Do not remove guards, shields, or screens while
operation. If removed for
maintenance replace before resuming operation.
Observe the delivery pressure gauge daily to be
sure the automatic control system is operating
Periodically check all safety and relief devices for
Use compressed air properly. Pressurized air can
Be sure that no tools, rags or loose parts are left
Do not use flammable solvents for cleaning
ise cleanliness during maintenance and
when making repairs. Keep dirt away from parts and
exposed openings by covering with clean cloth or
off valve in the discharge
line without installing a pressure relief valve
off and the compressor package.
Do not operate the compressor in areas where
there is a possibility of flammable or toxic
Never disconnect (or jump) the air discharge
safety device and
15. Know what mode of operation the compressor is
in before working around the unit. The power may
be on but the machine not running if it is in the auto
mode. Adhere to note #2 above.
1.4 Safety devices
WARNING!
Danger to life from nonfunctional
safety devices!
If safety devices are not functioning or
are disabled, there is a danger of grave
injury or death.
-
Check that all safety devices are
fully functional and co
installed before starting work.
-
Never disable or bypass safety
devices.
-
Ensure that all safety devices are
always accessible.
1.4.1
Position of the safety devices
The following illustrations show the position of the
safety devices.
Fig. 1: Emergency stop butto
n (1) on the screw
compressor 18–37
kW with tank (optional)
Safety
Danger to life from nonfunctional
If safety devices are not functioning or
are disabled, there is a danger of grave
Check that all safety devices are
fully functional and co
rrectly
installed before starting work.
Never disable or bypass safety
Ensure that all safety devices are
always accessible.
Position of the safety devices
The following illustrations show the position of the
n (1) on the screw
kW with tank (optional)