User Manual

FrSky is continuously adding features and improvements to our products. To get the most from your product, please check
the download section of the FrSky website www.frsky-rc.com for the latest update firmware and manuals
Instruction Manual for FrSky R9 Slim Receiver
• No Pulse: on loss of signal the receiver produces no pulses on any channel. To use this type, select it in the menu and
wait 9 seconds for the failsafe to take effect.
• Hold: the model will maintain the last position after the signal is lost. To use this type, select it in the menu and wait 9
seconds for the failsafe to take effect.
• Custom: the customized position of each individual channel. The model will move to the pre-set position after the signal
is lost. Move the cursor to “Set” and press ENTER, you will see FAILSAFE SETTING screen below. Move the cursor to
the channel you want to set failsafe on, and press ENTER. When moving the crresponding sticks or switches, you will
see the channel bar moving. Move the channel bar to the place you want for failsafe and long press ENTER to finish the
setting. Wait 9 seconds before the failsafe takes effect.
How to Set Failsafe mode (on the transmitter)
There are 3 failsafe modes: No Pulse, Hold, Custom
Note: If failsafe is not set, the model will hold the last position after signal is lost, thus it may fly away or
cause injury.
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
How to enable/disable the receiver telemetry
-- For Taranis X9D/X9D Plus and Taranis Q X7/X7S, go to the MENU-MODEL SETUP-PAGE2, choose External RF MODE
R9M LBT (EU) or FCC, then select Bind, choose the telemetry or not.
-- For Horus X12S/X10/X10S, turn on the transmitter. go to the RF SYSTEM, choose the External RF and select the R9M,
then select Bind under the STATE, choose the telemetry or not.
Note: After binding procedure is completed, resupply the power and check if the receiver is truly communicating
with the transmitter.
1.2 For Horus X12S/X10/X10S, turn on the transmitter, go to the RF SYSTEM, choose External RF (ON), and select BIND
under STATE.
2. Connect the battery to the receiver while holding the Bind button on the receiver. The RED LED on the receiver will flash,
indicating the binding process is completed.
3. Reboot the receiver and switch the RF module back to the normal mode. The flashing of the GREEN LED on the receiver
indicates the receiver is receiving commands from the transmitter.The binding of the receiver/transmitter moudle will not have
to be repeated, unless one of the two is replaced.
B:In PPM mode
1. For Non-EU Version, turn on Switch1 and Switch2 on R9M/For EU Version, select No Telemetry or Telemetry mode on
R9M, then power on R9M while holding its F/S button, Green LED will be on and Red LED will be flashing.
2. Connect the battery to the receiver while holding its Bind button. The Red LED on it will flash, indicating the binding process
in completed.
3. Reboot the R9M and the receiver. The flashing of the GREEN LED on the receiver indicates it is receiving commands from
the transmitter. The binding of the receiver/R9M will not have to be repeated unless one of the two is replaced.