User Manual

ManualsBrandsFrSky ManualsHobbyBattery Voltage Sensor - FrSky Telemetry System.

Alexander “Datos”

«http://forum.modelka.com.ua»

Using FrSky FLD-02 + battery level sensor FrSky FBVS01 + FrSky

D8R-II receiver. Short manual.

1.1 Specifications of

FrSky FLD-02

Model: FLD-02

Compatibility: FrSky DFT, DJT and DHT

Dimensions: 55*40*12mm

Screen resolution: 128*64

Backlight: yes, light-cyan

Power: from TX

1.2 Features:

1) Shows data from any compatible sensors connected to RX

2) Programmable alarms

3) Upgradable firmware

2 Quick start:

Connect FrSky FLD-02 to FRSky TX module using the cable supplied with FLD-02. Maintain polarity:

black wire means - ground. Make sure that both switches of FRSky TX module are at “OFF” position.

3 Screen structure:

3.1 Main screen:

FrSky logo

Firmware version

«DATA» button

«MENU» (settings) button

FrSky website

*note: you can scroll through buttons|values|digits by rotating upper button to either direction. Short

button press would choose|confirm value. Turning and keeping button for more than 1 second at

either end would set the cursor to the next location in more-than-one digit cell.

3.2 «MENU» Screen

Blаde: # of blades

Volt ratio: voltage divider on A1 (left cell) & A2 (right

cell) ports

Unit Set: Speed (KPH | MPH)

Temperature: (C | F)

Altitude: (meter | feet)

Alarm Set: alarm setup for A1_1/2, A2_1/2, RSSI_1/2

Summary of content (5 pages)

PAGE 1
Alexander “Datos” «http://forum.modelka.com.ua» Using FrSky FLD-02 + battery level sensor FrSky FBVS01 + FrSky D8R-II receiver. Short manual. 1.1 Specifications of FrSky FLD-02: Model: FLD-02 Compatibility: FrSky DFT, DJT and DHT Dimensions: 55*40*12mm Screen resolution: 128*64 Backlight: yes, light-cyan Power: from TX 1.
PAGE 2
3.2.1 D8R-II receiver (additional information) D8R-II receiver has 2 telemetry ports A1 and A2 (you can simultaneously connect either only 2 of any telemetry sensors or more than 2 sensors by using special sensor-hub) + 1 firmware upgrade port. A1 A2 Firmware upgrade port Port A1 has a default bridge installed from the factory between Х and A1 pins. Pin Х supplies power to a sensor. А1 pin receiver data from a sensor. G stands for Ground.
PAGE 3
.2.2 FBVS01 external battery level telemetry sensor This sensor has 3 voltage dividers - soldering pins: 1S (1-2 cell LiPO max. Divider for FLD02 = 2), 2S (1-4 cell LiPO max. Divider = 4), 3S (1-6 cell LiPO max. Divider = 6). Initially, red wire that goes to the battery is soldered to 3S pin on board, i.e. – any LiPO battery from 1 to 6 cells. In case of using, for example, up to 4 cells – you should re-solder it to 2S pin in order to get more accurate voltage metering by the sensor.
PAGE 4
3.3.2 How to setup an alarm for battery sensor readings (3-cell LiPO, connected to A2 telemetry RX port) In order to program low-battery alarm at a certain battery level, you should go to “MENU” Screen (section 3.
PAGE 5
3.3.5 Экран-3 Total Voltage Voltage for each cell *note: this screen would only be shown if FLVS-01 sensor is connected. Otherwise, Screen-4 would follow Screen-2 directly. 3.3.