Teacher: Part #2000-00049 Student: Part #2000-00050 Microphone User Guide AP Receiver AP Pendant Microphone AP Pass-Around Microphone AP Microphone Charger
Contents Important Safety Instructions ....................................................................................................................... 3 Electrical Warnings ....................................................................................................................................... 4 Electrical Safety Information: ................................................................................................................... 4 AP Pendant Microphone ......................
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, hear registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Electrical Warnings 1. Avoid Abuse to the Power Supply To reduce risk of electric shock, unplug the power supply from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. DO NOT disassemble the power supply. Return the apparatus to Frontrow for qualified service and repair if required. Incorrect reassembly may result in a risk of electric shock or fire.
AP Pendant Microphone Front 1 Amazing Sound Quality and Superior Comfort 1 With FrontRow’s digital synthesis technology, the AP Pendant microphone uses a single cardioid microphone element to deliver superb pickup and audio quality. And combined with a high-isolation, low-noise, open air microphone suspension this lightweight (54g/1.9 oz) compact (69mmx36mm/ 2.7”x 1.4”) microphone with soft backing minimizes noise from friction against clothing, buttons or jewelry.
11 Battery Indicator Top In Use 11 OFF………………….....…….Battery Charged or in hibernation mode GREEN FAST FLASH……….Registration in Process RED SLOW FLASH ……...….Battery Low RED FAST FLASH ...……..….Battery Critically Low RED DOUBLE FLASH…..…..Battery Fault YELLOW DOUBLE FLASH…Registration/Connection Fault 12 When Charging GREEN SOLID……………...Battery charging GREEN SLOW FLASH…..…Battery fully charged 12 Wireless Indicator GREEN SOLID ……………… Connected and Unmuted ORANGE FADE IN/OUT…..
AP Pass-Around Microphone Front 1 2 1 Amazing Sound Quality With FrontRow’s digital synthesis technology, the AP Pass-Around microphone uses a single cardioid microphone element to deliver superb pickup and audio quality. And combined with a high-isolation, low-noise, open air microphone suspension, the AP Pass-Around microphone minimizes handling noise. 3 4 2 Photo Diodes Photo diodes sense when microphone is within room coverage range.
9 Battery Indicator In Use OFF………………….……….Battery Charged or in hibernation mode GREEN FAST FLASH…..…..Registration in Process RED SLOW FLASH …......….Battery Low RED FAST FLASH ………….Battery Critically Low RED DOUBLE FLASH……...Battery Fault YELLOW DOUBLE FLASH.. Registration/Connection Fault Top 10 9 When Charging GREEN SOLID……………...Battery charging GREEN SLOW FLASH…..…Battery fully charged Rear Cover Removed 10 Wireless Indicator GREEN SOLID ……………….Connected and Unmuted ORANGE FADE IN/OUT…….
Volume Your ezRoom is equipped with a powerful feedback suppression engine that helps avoid harsh squealing noise that would normally occur when a microphone gets too close to a speaker. Nevertheless, try to use volume settings for daily use that give good audibility without constantly activating the feedback suppression engine.
Registering your Microphone with the AP Receiver Both Pendant and Pass-Around microphones must be registered with the ezRoom’s AP Receiver (the ‘receiver’) to become operational. You will need: Access to the receiver’s registration button (i.e. wall controller with programmed button, receiver’s Mic Registration button or CM-900’s webpage.) Unscrew microphone battery door with supplied Phillips head screwdriver. Supplied registration pin or straightened paper clip Registration setup: 1.
Beacon LED Status Indicator Your ezRoom is equipped with a status indicator Beacon which helps you know the status of your device. The color of the Beacon will change based on what is happening with your system. It is also possible for your system to be configured to turn the Beacon off.
AP Pendant Microphone Using 1. Wake or remove the microphone from the charger, wait 10 seconds for the tone. 2. Place the lanyard around your neck, position the microphone 5 inches from your mouth by holding the adjuster and pulling the lanyard ends. To remove, tug the mic to release the magnet clasp. 5in/14cm 3. Press the Mute button. The Wireless indicator should be solid green. NOTE: Your microphone will go into standby mode (off) automatically after 10 minutes in mute mode or 10 minutes of silence.
Battery Installing the battery 1. Unscrew the battery door on the back of the microphone using the supplied Phillips screwdriver. 2. Fit silicone cushions on each end of the battery. 3. Insert the battery’s connector into the receptacle. 4. Insert the battery into the case. 5. Replace battery door. 6. For best performance, charge the battery in the microphone overnight before initial use.
Charging Charge your battery in one of 3 ways: Microphone charger – recommended. USB cable connected to your computer’s USB port*. USB cable connected to a USB to SC power adapter. *NOTE – When charging from a computer USB port: If using laptop on battery power and the battery is low, the microphone will not charge. We recommend that you always have your laptop plugged in to a power source when attempting to charge your microphone. The microphone will not charge from a low-power USB port.
AP Pass-Around Microphone Using Battery indicator 1. Wake or remove the microphone from the charger, wait 10 seconds for the tone. Photo diodes 2. Press the mute button, be sure to press on the lower section of the button. Note the mute button is lit. Mute button Mute button LED On – On and transmitting Mute button LED Off – In sleep mode NOTE: In order to conserve battery life, your microphone will automatically go into Standby Mode (off) after 10 minutes of silence.
Battery Installing the battery 1. Unscrew the battery door on the back of the microphone using the supplied Phillips screwdriver. 2. Fit silicone cushions on each end of the battery. 3. Insert the battery’s connector into the receptacle. 4. Insert the battery into the case. 5. Replace battery door. 6. For best performance, charge the battery in the microphone overnight before initial use.
Charging Charge your battery in one of 3 ways: Microphone charger – recommended. USB cable connected to your computer’s USB port*. USB cable connected to a USB to SC power adapter. *NOTE – When charging from a computer USB port: If using laptop on battery power and the battery is low, the microphone will not charge. We recommend that you always have your laptop plugged in to a power source when attempting to charge your microphone. The microphone will not charge from a low-power USB port.
Using Multiple Microphones Your ezRoom system is designed to support up to 7 registered microphones and receive up to 4 microphone signals at once. A combination of Pass-Around and Pendant Microphones is possible. For example, use two Pendant Microphones (one for a teacher and one for a teacher’s aide) and two PassAround Microphones for students, or one Pendant Microphone and three Pass-Around Microphones for students. Microphone Charger Charger base bottom Charger setup 1.
Regulatory Put regulatory notes here similar to: (change ICR, ITM, ISM naming) Declaration of Conformity Update this section when available. Update similar to: TBD Batteries Batteries contain substances that can be harmful to human health and the environment if not handled correctly. Batteries are marked with the WEEE symbol. This symbolizes that exhausted batteries must not be disposed of together with unsorted rubbish, but are to be collected separately.
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
IC Warning This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada.
