Installation Manual

ManualsBrandsFront Runner Manuals4WD & CampingTent Mount Kit

IMPORTANT WARNING!

IT IS CRITICAL THAT ALL FRONT RUNNER RACKS AND ACCESSORIES BE PROPERLY AND SECURELY

ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT,

AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH TO YOU OR TO OTHERS. YOU ARE

RESPONSIBLE FOR SECURING THE RACKS AND ACCESSORIES TO YOUR CAR, CHECKING THE

ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT,

WEAR, AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND

CAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU

DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL

EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU

SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER SUCH AS A QUALIFIED

GARAGE OR AUTO BODY SHOP.

TENTBRACKETKIT

TBMK001

ZAR

INSTALL TIME: 1 hour

GET ORGANIZED

you will need:

 a 13 wrench

 a measuring tape

 a white marker

 a roof top tent

 a Front Runner roof rack

...CONT'D

Summary of content (5 pages)

PAGE 1
TENT BRACKET KIT ZAR TBMK001 INSTALL TIME: 1 hour 1 1 GET ORGANIZED you will need: a 13 wrench a measuring tape a white marker a roof top tent a Front Runner roof rack ...CONT'D IMPORTANT WARNING! IT IS CRITICAL THAT ALL FRONT RUNNER RACKS AND ACCESSORIES BE PROPERLY AND SECURELY ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH TO YOU OR TO OTHERS.
PAGE 2
1 GET ORGANISED ...CONT'D 1. Here is what you will receive in you kit... 1 5 2 4 3 1. 4 tent mounting brackets 2. 12 M8 washers 3. 12 M8 nylock nuts 4. 8 M8 x 16mm bolts 5. 4 M8 x 25mm bolts B) Familiarize yourself with the parts and then step away from the work area and read through these instructions from beginning to end. Grab a cup of coffee and take a moment.
PAGE 3
2 POSITIONING THE BRACKETS A) Depending on the position you are going to mount the tent, and the orientation of the tent opening, will determine where and which slats will be used to attach the tent brackets. Note: It is preferable to mount the tent brackets bridging two slats although it is possible to mount it on one slat B) C) To ensure your tent is centered. Grab your measuring tape and measure the width between the tracks (aluminum extrusions) mounted to the bottom of your tent.
PAGE 4
3 ...CONT'D ITEM # 1 2 3 4 5 6 7 Name SUPPORT BRACKET M8 WASHER M8 X 16MM BOLT M8 NYLOCK NUT M8 X 25MM BOLT TBMK006_011.PRT SLAT.PRT Quantity 4 8 8 8 4 4 2 B) Start by inserting the M8 x 16mm bolts into the T-slot in the slat (See image). Slide the bolts to the position where you have marked the slat. Fasten all four support brackets using your 13 wrench. Hand tighten as you might need to maneuver them slightly at a later stage.
PAGE 5
5 CHECK FOR OTHER COOL ACCESSORIES Now's the time to take a trip to your dealer or visit www.FRONTRUNNER.CO.ZA 6 TAKE A TRIP A) B) After your first adventure, check the tension on all the bolts and screws and re-tighten where needed. You'll find a small amount of settling has happened. Go on many more adventures. Periodically check the bolts- it's always wise to double check your fasteners once in a while.